CNCEST F007

Contents

Electric Telescoping Pole Chainsaw User Manual

Model: F007 | Brand: CNCEST

1. Introduction

Thank you for choosing the CNCEST F007 Electric Telescoping Pole Chainsaw. This cordless tool is designed for efficient and safe pruning of high branches in gardens, farms, parks, and other outdoor environments. Its high-quality construction, adjustable length, and powerful motor make it an indispensable tool for tree maintenance. Please read this manual thoroughly before assembly, operation, or maintenance to ensure safe and effective use of your pole saw.

Demonstration of the electric pole saw in use.

2. Important Safety Warnings

Always prioritize safety when operating power tools. Failure to follow these instructions may result in serious injury or property damage.

  • Read the Manual: Read the entire operating manual completely before use, paying particular attention to all safety instructions.
  • Personal Protective Equipment (PPE): Always wear appropriate safety gear, including safety glasses, gloves, hearing protection, and a hard hat when operating the pole saw.
  • Battery Safety:
    • Do not use damaged batteries or disassemble chargers or batteries.
    • The battery will explode if exposed to fire. Do not heat the battery.
    • When charging, it is normal for the charger and battery to heat slightly.
    • If the battery is not used for a long time, it must be recharged once every 3 months to prolong its service life.
    • New batteries or batteries that have not been used for a long time need about 5 charge-discharge cycles before reaching maximum capacity.
    • Do not recharge the battery after a short time of operation, as this may reduce the working time and efficiency of the battery.
  • Accidental Start-up Prevention: The machine can only be started by pressing the safety button and the switch at the same time. Ensure this sequence is followed to prevent accidental start-up.
  • Electrical Compatibility: Products with electrical plugs are designed for use in the US (or EU/UK depending on variant). Please check compatibility before purchasing and ensure proper voltage and frequency.
  • Work Area: Keep the work area clear of bystanders, children, and pets. Ensure stable footing and be aware of your surroundings, especially overhead power lines.
  • Chain Tightness: Pay attention to the tightness of the chain at all times. It is normal for the chain to slip slightly after operation and may require adjustment.

3. Package Contents

Verify that all items are present and undamaged upon opening the package.

  • 1 x Pole Saw (main unit)
  • 1 x Charger (US Standard)
  • 1 x Lithium Battery (1500mAh)
  • 1 x Screwdriver
  • 1 x Chain
  • 1 x English Manual
  • 1 x Guide Plate
All components included in the pole saw package

All components included in the pole saw package.

4. Assembly Instructions

The pole saw features a detachable design for easy transport and storage. Follow these steps to assemble your pole saw:

  1. Attach the Guide Plate and Chain: Carefully place the chain around the sprocket and guide plate. Ensure the chain is oriented correctly with the cutting edges facing forward.
  2. Secure the Sprocket Cover: Position the sprocket cover over the guide plate and chain. Use the built-in knob to fix the cover and adjust the chain tightness. No additional tools are required for this step.
  3. Connect the Pole Sections: The pole saw consists of multiple sections. Align the connectors and push them firmly together until they lock. Ensure the telescoping mechanism is securely fastened.
  4. Insert the Battery: Slide the fully charged lithium battery into the battery slot at the base of the handle until it clicks into place.
Disassembled view of the pole saw for transport or storage

Disassembled view of the pole saw for transport or storage.

Detailed view of the saw chain and guide plate

Detailed view of the saw chain and guide plate.

Detail of the adjustable telescoping pole

Detail of the adjustable telescoping pole.

5. Operating Instructions

Before operating, ensure you have read and understood all safety warnings and assembly instructions.

  1. Pre-Operation Check:
    • Ensure the battery is fully charged (approx. 2 hours for a full charge).
    • Check that the chain is properly tensioned and lubricated.
    • Inspect the pole saw for any loose parts or damage.
  2. Adjusting Length: The pole saw has an overall length of 1.25m (4.1ft). Adjust the telescoping pole to the desired length for reaching high branches. Secure the adjustment mechanism firmly.
  3. Starting the Pole Saw: To start the pole saw, simultaneously press the safety button (located near the trigger) and then squeeze the variable speed switch. The more pressure applied to the switch, the faster the saw chain will move.
  4. Pruning Technique:
    • Hold the pole saw firmly with both hands, maintaining a balanced stance.
    • Position the saw chain against the branch to be cut.
    • Allow the saw to reach full speed before engaging the branch.
    • Apply steady, even pressure. Do not force the saw through the branch.
    • Be aware of falling branches and clear the area below.
  5. Stopping the Pole Saw: Release the variable speed switch to stop the saw chain.
Man using the electric pole saw to prune high branches

Man using the electric pole saw to prune high branches.

Close-up of the pole saw's handle and battery attachment

Close-up of the pole saw's handle and battery attachment.

Ergonomic handle with trigger and safety button

Ergonomic handle with trigger and safety button.

6. Maintenance and Care

Regular maintenance ensures the longevity and safe operation of your pole saw.

  • Cleaning: After each use, clean the guide plate, chain, and motor housing to remove sawdust and debris. Use a dry cloth or soft brush. Do not use water or harsh chemicals.
  • Chain Lubrication: Regularly lubricate the saw chain according to standard chainsaw maintenance practices to ensure smooth operation and prevent wear.
  • Chain Tension: Periodically check and adjust the chain tightness. It is normal for the chain to loosen slightly after use. Use the built-in knob for tool-free adjustment.
  • Battery Storage: If the battery is not used for a long time, recharge it once every 3 months to maintain its lifespan. Store batteries in a cool, dry place away from direct sunlight and extreme temperatures.
  • Inspection: Regularly inspect the pole saw for any signs of wear, damage, or loose fasteners. Replace worn or damaged parts immediately.
  • Heat Dissipation: Ensure the ventilation holes are clear of obstructions to facilitate efficient heat dissipation and prevent motor overheating.

7. Troubleshooting

This section addresses common issues you might encounter with your pole saw.

ProblemPossible CauseSolution
Pole saw does not startBattery not inserted correctly or discharged; Safety button not pressed; Faulty switch.Ensure battery is fully charged and correctly inserted. Press safety button simultaneously with the trigger. If issue persists, contact support.
Chain stops or slows down during cuttingLow battery power; Chain too loose or too tight; Dull chain; Overload.Recharge battery. Adjust chain tension. Sharpen or replace chain. Reduce cutting pressure.
Chain slips off guide plateChain too loose; Worn guide plate or chain.Adjust chain tension using the knob. Inspect guide plate and chain for wear and replace if necessary.
Excessive vibration or noiseLoose components; Damaged chain or guide plate.Check all connections and fasteners. Inspect chain and guide plate for damage and replace if needed.
Battery or charger gets hot during chargingNormal operation.This is normal. Ensure adequate ventilation around the charger and battery.

8. Technical Specifications

FeatureSpecification
ModelF007
BrandCNCEST
ColorBlack
MaterialManganese Steel, Alloy Carbon Steel, ABS
Rated Power552W
Power TypeRechargeable - Lithium Technology
Lithium Battery Model1500mAh
No-load Speed4500rpm
Saw Chain Speed1200m/min (66ft/s)
Guide Plate Length18cm (7.08in)
Chain Teeth Pitch2.5cm (0.98in)
Chain Thickness15mm (0.59in)
Input Voltage (Charger)AC 100-240V 50/60Hz
Output Voltage (Charger)DC21V 1A
Charging TimeApprox. 2 hours
Duration (Full Charge)Approx. 0.5 hours
Product Length1.25m (4.1ft)
Net Weight2.3kg (5.07 lbs)
Gross Weight2.8kg (6.17 lbs)
Battery IncludedYes
CertificationCE
Product dimensions including guide plate length, base size, and overall length

Product dimensions including guide plate length, base size, and overall length.

9. Warranty and Support

For any questions, technical assistance, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.