ANANDA D13

Contents

ANANDA D13 LCD Remote Kit Display

User Manual

1. Introduction

This manual provides essential information for the installation, operation, and maintenance of your ANANDA D13 LCD Remote Kit Display for electric bikes. The D13 display is designed to provide key information and control functions for your e-bike system.

Front view of the ANANDA D13 LCD display with its connecting cable.

Figure 1: ANANDA D13 LCD Display Overview

2. Setup and Installation

Important: The ANANDA D13 LCD Remote Kit Display is a customized product. Before installation, please ensure compatibility with your e-bike system. Contact your seller if you have any doubts or require specific configuration information.

2.1 Package Contents

  • ANANDA D13 LCD Display Unit
  • Integrated connecting cable with 5-pin connector
  • Mounting bracket (pre-attached or separate)

2.2 Mounting the Display

  1. Identify a suitable location on your handlebar for the display. Ensure it does not obstruct your view or control of the bike.
  2. Secure the display's mounting bracket to the handlebar using the provided screw. Tighten securely but do not overtighten.
  3. Adjust the angle of the display for optimal visibility.

2.3 Connecting the Display

  1. Locate the corresponding connector on your e-bike's wiring harness. This is typically a 5-pin connector.
  2. Align the pins of the display's cable connector with the e-bike's harness connector.
  3. Gently push the connectors together until they click into place, ensuring a secure connection.
  4. Route the cable neatly along the handlebar and frame, securing it with cable ties if necessary, to prevent snagging or damage.

Video 1: Demonstration of the ANANDA D13 display and its 5-pin connector.

Close-up view of the 5-pin connector on the ANANDA D13 display cable.

Figure 2: Detail of the 5-pin connector

3. Operating Instructions

The ANANDA D13 display features three buttons for control: '+', '⚡/M', and '-'.

Close-up of the ANANDA D13 display buttons: plus, power/mode, and minus.

Figure 3: D13 Display Buttons

3.1 Power On/Off

  • To power on the display and your e-bike system, press and hold the '⚡/M' button for a few seconds.
  • To power off, press and hold the '⚡/M' button again until the display turns off.

3.2 Adjusting Assist Levels

  • Use the '+' button to increase the pedal assist level.
  • Use the '-' button to decrease the pedal assist level.

3.3 Changing Display Modes

  • Press the '⚡/M' button briefly to cycle through different display modes (e.g., speed, distance, battery level, trip time).

3.4 Automatic Features

  • The display supports automatic sleep and auto-pause functions to conserve battery life. These features activate after a period of inactivity.

4. Maintenance

  • **Cleaning:** Wipe the display screen and body with a soft, damp cloth. Do not use abrasive cleaners or solvents.
  • **Storage:** When not in use for extended periods, store the display in a dry place within the specified storage temperature range (-30℃ to 70℃).
  • **Connection Check:** Periodically check that all connections are secure and free from corrosion or damage.

5. Troubleshooting

  • **Display Not Turning On:**
    1. Ensure the e-bike battery is charged and properly connected.
    2. Check all cable connections, especially the 5-pin connector to the display, for looseness or damage.
    3. If the issue persists, contact your seller for further assistance.
  • **Incorrect Readings:**
    1. Verify that the display is securely mounted and not vibrating excessively.
    2. If speed or distance readings are inaccurate, consult your e-bike's main controller manual or seller for calibration procedures.
  • **Water Ingress:** The display has an IPX7 waterproof rating, meaning it can withstand immersion in water up to 1 meter for 30 minutes. However, avoid prolonged exposure to heavy rain or submersion. If water ingress occurs, disconnect power immediately and allow the unit to dry completely before attempting to use it again.

6. Specifications

Back view of the ANANDA D13 display showing the mounting bracket.

Figure 4: Back view with mounting bracket

FeatureSpecification
Model NumberD13
Power Supply24V/36V/48V
Rated Working Current10mA
Maximum Working Current30mA
Off-state Leakage Current<1μA
Working Temperature-20℃ ~ 60℃
Storage Temperature-30℃ ~ 70℃
Waterproof LevelIPX7
Automatic SleepYes
Auto-pauseYes
Touch ScreenNo
NavigationNo

7. User Tips

  • **Speed Limit:** The display may be configured with a maximum speed lock, commonly set to 25 km/h, depending on regional regulations and e-bike settings.
  • **Customization:** As a customized product, specific functionalities or settings might vary. Always refer to any additional documentation provided by your e-bike manufacturer or seller for detailed customization options.

8. Warranty and Support

For any questions, problems, or support needs regarding your ANANDA D13 LCD Remote Kit Display, please contact your seller directly. They are best equipped to provide assistance tailored to your specific product and e-bike configuration.

The product typically includes a free return policy within 90 days of receipt. Please consult the seller's return policy for specific terms and conditions.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.