1. Introduction
The PORTXVNSA NanoVNA-H4 Plus is a portable handheld vector network analyzer (VNA) designed for precise measurement of reflection and transmission coefficients. This upgraded version features an extended measurement frequency range of 50KHz to 2.7GHz and an increased number of scan points to 401, offering enhanced performance over previous models. Its ergonomic design, resistive touch screen, and large knob operation ensure convenient and intuitive use.

Figure 1: NanoVNA-H4 Plus Vector Network Analyzer and its accessories.
Key Features:
- Ergonomic design for improved handling.
- Measurement range upgraded to 50KHz-2.7GHz with 401 scan points.
- Supports SD card for easy storage and export of test data.
- Resistive touch screen and large knob for convenient operation.
- Built-in 5000mAh battery for extended battery life.
- 4-inch IPS LCD display with wide viewing angle, accurate color reproduction, high contrast, and uniform brightness.
2. Package Contents
The NanoVNA-H4 Plus is available in two sets. Please verify your package contents upon receipt.
Set 1 Packaging List:
- USB Type-C cable x1
- 15cm SMA male to male TG316 RF cable x2
- SMA Male Calibration Kit OPEN x1
- SMA Male Calibration Kit Short Circuit x1
- SMA Male Calibration Kit LOAD x1
- SMA female to female connector x1
- Type-C to Type-C cable x1
- Touch Pen x1
- Pick x1
- NanoVNA-H4 PLUS Host x1
Set 2 Packaging List:
- USB Type-C cable x1
- 15cm SMA male to male TG316 RF cable x2
- SMA Male Calibration Kit OPEN x1
- SMA Male Calibration Kit Short Circuit x1
- SMA Male Calibration Kit LOAD x1
- SMA female to female connector x1
- Type-C to Type-C cable x1
- Touch Pen x1
- Pick x1
- NanoVNA-H4 PLUS Host x1
- 32G memory card x1

Figure 2: NanoVNA-H4 Plus and accessories securely packaged in a foam insert.
3. Specifications
| Attribute | Value |
|---|---|
| Measurement Bandwidth | 50KHz-2.7GHz |
| Frequency Range | 50KHz-2.7GHz |
| Dynamic Range | 80dB (50KHz-900MHz), 60dB (900MHz-1.5GHz), 50dB (1.5GHz-2.7GHz) |
| Reflection Coefficient (SWR) | <1.1 |
| Frequency Accuracy | <0.5 ppm |
| Frequency Stability | <2.5 ppm |
| Scan Points | 401 |
| Product Size | 160x92x35mm |
| Battery Included | Yes (Built-in 5000mAh) |
| Semi-finished product | No |
| High-concerned chemical | None |
| Origin | Mainland China |
| Certification | NONE |
4. Safety & Warnings
Warning!
- This product is intended for adult use only.
- Keep out of reach of children and pets to prevent accidental injury or ingestion.
- Always check if the installation is correct before operation.
- If you observe abnormal noise or equipment errors during or after installation, immediately stop using the device.
- Follow all instructions for proper use. Misuse may cause harm.
- Store the product in a dry and shady place, away from high temperatures, humidity, and direct sunlight.
5. Setup
Before First Use:
Ensure the product is free from any visible damage. Inspect all components and accessories for integrity.
Charging the Device:
The NanoVNA-H4 Plus has a built-in 5000mAh rechargeable battery. Connect the device to a power source using the provided USB Type-C cable to charge it before initial use.
Connecting to PC (Optional):
The device supports PC control via Nano Saver software. Connect the VNA to your computer using the USB Type-C cable. Nano Saver is a multiplatform tool that allows you to save Touchstone files, sweep frequency spans, and analyze data.

Figure 3: PC control via Nano Saver, showing Type-C port and 5000mAh rechargeable battery.
6. Operating Instructions
The NanoVNA-H4 Plus features a resistive touch screen and a large knob for intuitive navigation and operation.
Basic Navigation:
- Use the resistive touch screen to select menu options and input values.
- The large knob can be used to scroll through menus, adjust parameters, and confirm selections.

Figure 4: Interacting with the resistive touch screen for menu selection.
Menu Structure:
The device's menu structure allows access to various functions including trace display, marker settings, stimulus control, calibration, recall/save functions, SD card management, and configuration settings. A detailed menu structure map is provided below for reference.

Figure 5: Detailed Menu Structure Map for the NanoVNA-H4 Plus.
Performing Measurements:
The NanoVNA-H4 Plus is capable of various measurements, including:
- Scanning antenna systems and cables.
- SWR and impedance matching.
- Measuring dual-band and triple-band duplexers.
- Port isolation by frequency band.
- Measuring insertion loss of filters.
- Measuring 2.4 GHz antennas, shortwave antennas, and cable length.

Figure 6: Various applications of the NanoVNA-H4 Plus, including antenna scanning, SWR, and filter measurements.

Figure 7: Examples of measurements, including 2.4 GHz antenna, shortwave antenna, and cable length.
Video Demonstration:
Video 1: A demonstration of the NanoVNA-H4 Plus user interface and functionality, showing menu navigation and parameter adjustments.
7. Maintenance
After Use:
Store the product in a dry and shady place. Keep it away from high temperatures, humidity, and direct sunlight. Ensure it is stored out of reach of children and pets.
Cleaning:
Use a soft, dry cloth to clean the device. Do not use abrasive cleaners or solvents.
8. Troubleshooting
- Jog Wheel Freezes: If the jog wheel becomes unresponsive, you can still use the resistive touch screen for navigation and input.
- Missing Memory Card: If your package (Set 2) was supposed to include a 32GB memory card and it is missing, please contact your seller for assistance.
- Abnormal Noise or Equipment Error: Immediately stop using the device and contact support if you experience any unusual sounds or malfunctions.
9. User Tips
- The device often comes with the penultimante firmware version from Dislord, so an immediate update might not be necessary.
- The enclosure is sturdy and well-made, providing a professional feel.
- The knob control is a preferred method of interaction for many users, offering an alternative to the stylus.
- The screen is clear and bright, enhancing readability of measurement data.
10. Warranty & Support
Manufacturer Information:
Shenzhen Kace Technology Co., Ltd.
Address: 401, Building 3, Hengchangrong (Xinghui) Science and Technology Park, No. 52, Huaning Road, Xinshi Community, Dalang Street, Longhua District, Shenzhen, Guangdong Province Code: 518000
Email: ivandjy@163.com
Phone: 8617673043225
EU Authorized Representative:
MJCM SARL
Address: 78 avenue des Champs Elysees Bureau 326, France
Email: mjcm190928@gmail.com
Phone: 33-767213611
Additional Resources:
A detailed user manual in PDF format is available for further reference. You can access it via the following link: NanoVNA-H4 Plus User Manual (PDF)