1. Introduction
The ONWA KS-200A is a high-performance Class B+ Automatic Identification System (AIS) transponder designed for marine vessels. This device transmits your vessel's information and receives data from other AIS-equipped vessels and shore stations, enhancing situational awareness and collision avoidance. Utilizing SOTDMA technology, similar to Class A AIS, it ensures guaranteed time slot allocation for reliable data transmission. With a 5W transmission power, it offers increased range and improved AIS satellite reception for global tracking capabilities.

2. Specifications
| Characteristic | Value |
|---|---|
| AIS Characteristics | |
| Frequency Rate | 156.025 MHz ~ 162.025 MHz |
| Access Scheme | SOTDMA |
| Channel Bandwidth | 25 KHz |
| Modulation | GMSK |
| Number of AIS Transmitter | 1 |
| Number of AIS Receiver | 2 |
| AIS Channel 1 | CH 87B (161.975 MHz) |
| AIS Channel 2 | CH 88B (162.025 MHz) |
| Tx Power Output | >5 Watt (37 dBm ± 1.5 dB) |
| RX Sensitivity | <-123dBm @ 20% PER |
| RX Message Format | AIS Class A and B messages |
| Comply Standard | IEC-62287 IEC 62287-2 Ed. 2.0:2017 |
| NMEA | |
| NMEA Sentence Supported | VDM, VDO, RMC, GSV, GGA, GSA |
| GPS Receiver (AIS Internal) | |
| Compliance | IEC61108-1 compliant |
| Physical | |
| Dimension (L x W x H) | 207mm x 155.8mm x 50mm |
| Weight | 0.8kg |
| Power Supply | |
| Input Voltage | 10 ~ 35 VDC |
| Current Consumption | 0.35A nominal, 2A peak |
| Environment | |
| Operating Temperature | -25°C to +55°C |
| Electrical Interface | |
| Data Interface | RS232 38.4kbaud bi-directional |
3. Setup and Installation
Proper installation is crucial for the optimal performance of your KS-200A AIS Transponder. Refer to the interconnection diagram below for wiring details.

3.1 Power Connection
Connect the red wire (+) and black wire (-) from the power/data cable to a 10-35 VDC power supply. Ensure the power supply is stable and within the specified voltage range.
3.2 Antenna Connections
- VHF Antenna: Connect a suitable VHF antenna to the 'VHF ANT' connector on the transponder. This antenna is essential for both transmitting and receiving AIS signals.
- GPS Antenna: Connect the GPS antenna to the 'GPS ANT' connector. This provides the necessary positioning data for your AIS transmissions.
3.3 Data Connection
The 'DATA' port (8-pin connector) provides an RS232 bi-directional interface. Use this port to connect the transponder to an external display device such as a laptop, chartplotter, or radar system. Ensure the data cable is securely connected and configured correctly on your external device to receive NMEA data (VDM, VDO, RMC, GSV, GGA, GSA sentences).


4. Operating Instructions
4.1 Powering On/Off
Locate the 'ON/OFF' switch on the rear panel of the transponder. Flip the switch to 'ON' to power on the device. The 'POWER' indicator on the front panel should illuminate. To power off, flip the switch to 'OFF'.
4.2 Indicator Lights
The front panel features three indicator lights:
- POWER: Illuminates when the device is powered on.
- TX (Transmit): Flashes when the transponder is actively transmitting AIS data.
- RX (Receive): Flashes when the transponder is actively receiving AIS data from other vessels.

4.3 Data Transmission and Reception
Once powered on and properly connected to the antennas and an external display, the KS-200A will automatically begin transmitting your vessel's AIS data and receiving data from other vessels. Monitor the TX and RX indicator lights to confirm activity. The received AIS data will be displayed on your connected chartplotter or PC software, providing real-time information about nearby vessels.
5. Maintenance
- Cleaning: Regularly wipe the unit with a soft, dry cloth to remove dust and salt residue. Avoid using harsh chemicals or abrasive cleaners.
- Connection Checks: Periodically inspect all cable connections (power, data, VHF antenna, GPS antenna) to ensure they are secure and free from corrosion.
- Antenna Inspection: Ensure your VHF and GPS antennas are clear of obstructions and in good physical condition. Damaged antennas can significantly reduce performance.
- Software Updates: Check the manufacturer's website for any available firmware updates for your KS-200A transponder. Follow the provided instructions carefully for any update procedures.
6. Troubleshooting
6.1 No Power
- Check Power Supply: Ensure the power source (10-35 VDC) is active and providing the correct voltage.
- Verify Connections: Confirm that the red (+) and black (-) power wires are correctly and securely connected.
- Power Switch: Make sure the 'ON/OFF' switch on the rear panel is in the 'ON' position.
6.2 No AIS Data on Display
- Antenna Connections: Check that both the VHF and GPS antennas are securely connected to the transponder.
- Data Cable: Ensure the data cable is properly connected between the transponder's 'DATA' port and your external display device.
- Display Settings: Verify that your chartplotter or PC software is correctly configured to receive NMEA data at 38.4kbaud from the connected port.
- Indicator Lights: Check if the TX and RX lights are flashing. If not, there might be an issue with the unit's operation or antenna signal.
6.3 Poor AIS Range or Intermittent Data
- Antenna Placement: Ensure the VHF antenna has a clear, unobstructed view of the horizon. Any metal structures or other antennas nearby can interfere.
- Antenna Condition: Inspect the VHF antenna and its cable for any damage or corrosion.
- GPS Signal: Ensure the GPS antenna has a clear view of the sky to acquire satellite signals.
7. User Tips
- Optimal Antenna Placement: For best performance, mount your VHF antenna as high as possible on your vessel with a clear 360-degree view.
- Dedicated Power Circuit: Consider connecting the AIS transponder to a dedicated power circuit to minimize electrical interference from other onboard electronics.
- Software Configuration: Familiarize yourself with your chartplotter or PC navigation software's AIS settings to customize display options and alarms.
- MMSI Programming: Ensure your vessel's MMSI (Maritime Mobile Service Identity) is correctly programmed into the transponder. This is a critical step for proper AIS operation and is usually done during initial setup by a qualified technician or according to local regulations.
8. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or contact your authorized ONWA dealer or the manufacturer directly. Keep your proof of purchase for warranty claims.