1. Introduction
Thank you for choosing the HOMCOM 2000W Low Consumption Electric Heater. This heater is designed to provide efficient and comfortable warmth for spaces up to 20 m², featuring PTC ceramic heating technology for rapid and uniform heat distribution. With multiple operating modes, an adjustable thermostat, and advanced safety features, it ensures a cozy environment without excessive energy consumption. Please read this manual thoroughly before use to ensure safe and optimal operation.

2. Safety Instructions
- Always place the heater on a firm, level surface.
- Do not cover the heater or block the air inlets/outlets.
- Keep flammable materials (curtains, furniture, etc.) at least 1 meter away from the heater.
- Do not use the heater in bathrooms, laundry areas, or similar wet locations.
- Unplug the heater when not in use or before cleaning.
- Ensure the power cord is not damaged and is placed safely to avoid tripping hazards.
- This heater is equipped with V0 flame retardant materials and a safe plug.
- Features tip-over protection: the heater will automatically shut off if knocked over.
- Includes overheating protection: the heater will automatically shut off if it reaches an unsafe temperature.
3. Setup
The HOMCOM Electric Heater requires no assembly. Simply follow these steps:
- Unpack the heater and remove all packaging materials.
- Place the heater on a stable, flat, and heat-resistant surface. Ensure there is adequate clearance around the heater for proper airflow (at least 1 meter from walls or other objects).
- Plug the power cord into a suitable electrical outlet (AC 220-240V, 50/60Hz).
- The heater is now ready for operation.
4. Operating Instructions
The heater can be operated using the control panel on top of the unit or the included remote control.
4.1 Control Panel and Remote Control


4.2 Power On/Off
- Press the 'ON/OFF' button on the control panel or remote control to turn the heater on or off.
4.3 Mode Selection
Press the 'MODE' button on the control panel or remote control to cycle through the available modes:
- Fan Mode: Circulates air without heating.
- Low Heat (1200W): Provides moderate heating.
- High Heat (2000W): Provides maximum heating.

4.4 Temperature Adjustment
The heater allows you to set the desired temperature between 22°C and 28°C. Use the temperature adjustment buttons (usually '+' and '-' or a dedicated temperature button) on the control panel or remote to select your preferred temperature.
4.5 Oscillation Function
Press the 'OSC' (Oscillation) button on the control panel or remote control to activate or deactivate the 60° oscillation function. This feature helps distribute warm air evenly across a wider area.

4.6 Timer Function
The programmable timer allows you to set the heater to operate for a specific duration, up to 15 hours. Press the 'TIMER' button on the control panel or remote control to set the desired operating time. The display will show the selected duration (e.g., 1h, 2h, 4h, 8h, up to 15h).
5. Maintenance
Regular maintenance ensures the longevity and efficient operation of your heater.
- Cleaning: Before cleaning, always unplug the heater and allow it to cool down completely. Use a soft, damp cloth to wipe the exterior surfaces. Do not use abrasive cleaners or solvents.
- Dust Removal: Periodically use a vacuum cleaner with a brush attachment to remove dust from the air inlets and outlets.
- Storage: If storing the heater for an extended period, ensure it is clean and dry. Store it in its original packaging in a cool, dry place.
- No User-Serviceable Parts: Do not attempt to open or repair the heater yourself. Refer all servicing to qualified personnel.
6. Troubleshooting
If you encounter any issues with your heater, please refer to the following common problems and solutions:
- Heater does not turn on:
- Ensure the power cord is securely plugged into a working outlet.
- Check if the power outlet is functioning by plugging in another appliance.
- Verify that the heater's power button is pressed.
- Check for tip-over or overheating protection activation. If activated, unplug the heater, wait a few minutes, and then plug it back in.
- No heat output:
- Ensure the heater is in a heat mode (Low or High), not just Fan mode.
- Check the thermostat setting; it might be set lower than the ambient room temperature.
- Oscillation not working:
- Press the 'OSC' button to ensure the function is activated.
- Remote control not working:
- Check and replace the batteries in the remote control.
- Ensure there are no obstructions between the remote and the heater.
If the problem persists after trying these solutions, please contact customer support.
7. Specifications
| Feature | Specification |
|---|---|
| Brand | HOMCOM |
| Model | 820-492V90WT |
| Color | White |
| Material | PP (Polypropylene) |
| Total Measurements (LxWxH) | 21 cm x 19.7 cm x 61 cm |
| Air Outlet Measurements (LxW) | 31 cm x 5 cm |
| Temperature Range | 22°C - 28°C |
| Power Settings | Fan, Low Heat (1200W), High Heat (2000W) |
| Coverage Area | 15-20 m² |
| Rated Voltage/Frequency | AC 220-240V, 50/60Hz |
| Cable Length | 1.5 m |
| Remote Control Range | 5 m |
| Oscillation Angle | 60° |
| Timer | Up to 15 hours |
| Safety Features | Tip-over protection, Overheating protection, V0 flame retardant materials, Safe plug |
| Package Dimensions (LxWxH) | 21 cm x 17 cm x 63 cm |
| Package Weight | 3.1 kg |

8. User Tips
- For optimal heating, place the heater in the center of the room or near the area you wish to warm most.
- Utilize the oscillation function to distribute heat more broadly and efficiently throughout the room.
- Use the timer function to automatically turn off the heater, saving energy and ensuring comfort without continuous operation.
- Adjust the temperature setting to your comfort level. The heater will maintain the set temperature, cycling on and off as needed.
- Keep the remote control in an easily accessible location for convenient operation from a distance.
9. Warranty and Support
For any questions, concerns, or technical support regarding your HOMCOM Electric Heater, please contact HOMCOM customer service. Keep your purchase receipt as proof of purchase for warranty claims.
Please refer to the official HOMCOM website or your retailer for specific warranty terms and contact information.