Introduction
This manual provides detailed instructions for assembling the Trumpeter 00931 1:16 Scale US MaxxPro MRAP Vehicle Plastic Assembly Building Model Kit. This static model kit is designed for enthusiasts aged 14 and above, offering a highly detailed replica of the Mine Resistant Ambush Protected (MRAP) vehicle. Please read all instructions carefully before beginning assembly.
Safety Precautions
- This product contains small parts and is not suitable for children under 14 years of age.
- Exercise caution when using modeling knives, sprue cutters, and other sharp tools.
- Always work in a well-ventilated area when using glues and paints.
- Keep all parts and tools out of reach of small children and pets.
- WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Kit Contents
The kit consists of over 240 parts, including:
- Plastic sprues (approximately 10 pieces for upper body, chassis, frame, and various components)
- Rubber tires
- Metal parts (pins, shafts, hinges, screws)
- Photo-etched parts (1 piece)
- Decal sheet
- Instruction manual (including painting and marking guide)
Figure 1: Kit box with contents overview.
Setup and Assembly
Assembling and coloring the model requires a certain amount of hands-on ability. The completed model's appearance may vary based on individual skill.
Before Assembly:
- Study and understand these instructions thoroughly before beginning assembly.
- Familiarize yourself with all parts and their placement.
- Ensure you have all necessary tools (not included): plastic cement, sprue cutters, long-nose pliers, modeling knife, small files, tweezers, pin vise & drill bits, soft cloth, and sandpaper.
- Glue and paint are not included in the kit. Use plastic cement and hobby paints only.
General Assembly Steps:
- Carefully remove parts from the sprues using sprue cutters. Use a modeling knife for photo-etch parts, taking care not to damage or lose small pieces.
- Clean any excess plastic (flash) from the parts using a modeling knife or file.
- Dry-fit parts before applying cement to ensure proper alignment.
- Apply instant cement sparingly to join parts as instructed in the detailed diagrams.
- Follow the numerical sequence in the painting and marking guide for assembly and painting.
Decal Application:
- Cut decals from the sheet as needed.
- Dip the decal in warm water for about 10 seconds and then place it on a soft clean cloth.
- Hold the decal backing sheet edge and gently slide the decal onto the model in its proper position.
- While still wet, the decal can be adjusted for better fit on the model by dampening it gently with your finger.
- When placed in the proper position, gently press the decal down with a soft cloth until excess water and air bubbles are gone.
- Allow the decal to dry completely before handling the model.
Figure 2: Painting and Marking Guide. Refer to this guide for color schemes and decal placement.
Figure 3: Decal Sheet. Contains various markings for the US MaxxPro MRAP.
Figure 4: Example of a plastic sprue with small detail parts.
Figure 5: Rubber tires and metal components (pins, shafts, screws).
Operating and Display
This is a static display model. Once assembled, it is not intended for rough play or functional operation. Handle the finished model with care to prevent damage to delicate parts.
Display Tips:
- Choose a stable, flat surface away from direct sunlight, extreme temperatures, and high humidity.
- Avoid placing the model in areas prone to dust accumulation or vibrations.
Figure 6: Fully assembled US MaxxPro MRAP model.
Maintenance
Proper care will ensure the longevity of your model.
Cleaning:
- Gently dust the model regularly with a soft, dry brush or a microfiber cloth.
- For stubborn dust, a slightly damp cloth (water only) can be used, but ensure no moisture remains in crevices.
- Avoid using harsh chemicals, solvents, or abrasive cleaners, as these can damage paint and plastic.
Storage:
- If storing the model, place it in a sturdy box with soft packing material to prevent movement and damage.
- Store in a cool, dry place away from direct sunlight and extreme temperature fluctuations.
Troubleshooting Common Assembly Issues
- Parts not fitting: Ensure you are using the correct parts as indicated in the instructions. Check for any excess plastic (flash) that might be preventing a snug fit and carefully trim if necessary.
- Decals not adhering: Make sure the surface is clean and smooth. Use a decal setting solution to help the decal conform to irregular surfaces and improve adhesion.
- Missing or damaged parts: Carefully check all sprues and packaging. If a part is genuinely missing or damaged upon receipt, contact the seller for assistance.
Specifications
| Feature | Detail |
|---|---|
| Product Name | US MaxxPro MRAP Mine Resistant Anti Ambush Vehicle |
| Model Number | 00931 |
| Brand | Trumpeter |
| Scale | 1:16 |
| Product Type | Static Kit |
| Model Size (Approx.) | Length: 433.6mm, Width: 198mm |
| Total Parts | 240+ |
| Material | Plastic (ABS) |
| Metal Parts Included | Pins, shafts, hinges, screws |
| Photo-Etched Parts | 1 piece |
| Recommended Age | 14+ years |
| Certification | CE |
| Origin | Mainland China |
| Package Dimensions (Approx.) | Length: 63 cm, Width: 35 cm, Height: 23 cm |
| Package Weight (Approx.) | 6.5 kg |
User Tips
- Inspect Contents: Upon receiving your kit, carefully inspect all sprues and components for any damage or missing parts before starting assembly.
- Test Fit: Always dry-fit parts before applying glue. This helps identify potential fit issues and allows for adjustments.
- Thin Glue Application: Use plastic cement sparingly. A small amount is usually sufficient for a strong bond, and it helps prevent unsightly glue marks.
- Patience with Decals: Decal application can be tricky. Take your time, use plenty of water, and consider using decal setting solutions for best results, especially on curved surfaces.
- Painting Prep: Clean plastic parts thoroughly before painting to remove any mold release agents or oils, which can affect paint adhesion.
Warranty and Support
For any questions regarding assembly, missing parts, or product support, please contact the seller directly. Keep your purchase records handy for faster service.