NEEWER Z120 SE

Contents

NEEWER Basics Z120 SE Mini Camera Flash Speedlite Instruction Manual

Model: Z120 SE

Introduction

Thank you for purchasing the NEEWER Basics Z120 SE Mini Camera Flash Speedlite. This manual provides detailed instructions for safe operation, setup, and maintenance of your new flash unit. Please read this manual thoroughly before use to ensure optimal performance and longevity of the product.

NEEWER Basics Z120 SE Mini Camera Flash Speedlite with accessories

Figure 1: NEEWER Basics Z120 SE Mini Camera Flash Speedlite and included accessories.

Safety Tips

Please read and understand these safety precautions before using the product.

  1. Do not trigger the flash near flammable or liquid gases (such as gasoline, solvents, etc.). Danger of explosion!
  2. Do not use flash photography on drivers of cars, buses, or trains, or on motorcycles or bicycles. They may be temporarily blinded by the strong light, which may lead to traffic accidents!
  3. Do not trigger the flash at close range to the eyes! The use of flash on human or animal eyes can damage the retina, leading to serious visual disorders and even blindness!
  4. Use only the power supply listed in this manual!
  5. Do not expose the battery to extreme heat, such as sunlight or fire!
  6. Do not let the flashlight or battery charge come into contact with dripping or splashing water (such as rainwater)!
  7. Protect your flash in extreme heat or humidity!
  8. Do not place the flash in the glove compartment. When the flash is triggered, do not place transparent objects in front of or above the reflecting screen. There should not be any dirt on the reflecting screen. Otherwise, the high energy generated by the flash will burn the objects on the reflecting screen or damage the reflecting screen.
  9. Do not touch the flash after continuous triggering. Danger of cautery!
  10. Do not remove the flash by yourself! Danger of high voltage contact! Non-professional personnel shall not carry out repairs to the components inside the flash lamp.
  11. When shooting fast and continuously with full-light output, the interval must be at least 15 minutes after 10 flashes!
  12. When shooting fast and continuously with full-light output, the interval must be at least 15 minutes after 10 flashes!

Product Overview

Familiarize yourself with the components of your Z120 SE Mini Camera Flash Speedlite.

Diagram of NEEWER Z120 SE Mini Camera Flash with numbered parts

Figure 2: Z120 SE Mini Camera Flash Speedlite Part Names.

Part Names:

  1. Type-C charging Port
  2. Power Switch
  3. Test flash key
  4. MODE selection key
  5. Display
  6. Power adjustment “-” key
  7. Power adjustment “+” key
  8. Hot shoe locking option
  9. Hot Shoe
  10. Single touch

Specifications

Table of specifications for NEEWER Z120 SE Mini Camera Flash

Figure 3: Detailed specifications of the Z120 SE Mini Camera Flash.

FeatureDescription
ModelZ120 SE
Item TypeCamera Speedlite
ColorBlack
CompatibilityFor Cameras with Hot Shoe (Canon, Nikon, Sony, Fujifilm, Pentax, Olympus)
ApplicationPortrait/Indoor Photography
Main FeaturesCompact/Lightweight/Bright
Main MaterialPlastic
Guide Number (GN)12
Power Levels8 (1/128-1/1)
Recycling Time0.1-1.8s
Supported Camera Shutter Speedup to 1/250s
Modes3 (M/S1/S2)
Color Temperature5600K
Built in Battery Capacity2000mAh, 3.7V
Number of Flashes500 Full Power Flashes
Dimensions2.9"x2.8"x1.84" / 73.7x71.1x46.8mm
Weight4.52oz / 128g

Note: This flash does NOT support TTL function and high-speed synchronization function. When used with lenses below 88mm, if the focal length is too long, the bottom of the frame may be underexposed.

Package Contents

The following items are included in your NEEWER Basics Z120 SE package:

  • 1x Speedlite (Z120 SE Mini Camera Flash)
  • 1x Diffuser
  • 1x USB to Type-C Cable
  • 1x Storage Bag
NEEWER Z120 SE Mini Camera Flash and its accessories: diffuser, USB-C cable, and storage bag

Figure 4: Contents of the Z120 SE package.

Setup

1. Charging the Battery

Before first use, ensure the flash unit is fully charged.

  1. Locate the Type-C charging port (1) on the flash unit.
  2. Connect the provided USB to Type-C cable to the flash unit and a compatible 5V 2A USB power adapter (not included).
  3. The charging indicator will light up during charging. A full charge takes approximately 3 hours.
  4. Once fully charged, the charging indicator will change or turn off (refer to the display for status).
Close-up of NEEWER Z120 SE flash showing Type-C charging port

Figure 5: Type-C charging port on the Z120 SE flash.

2. Attaching to Camera

The Z120 SE is compatible with standard single contact hot shoe cameras.

  1. Ensure your camera is turned off.
  2. Slide the hot shoe (9) of the flash unit into your camera's hot shoe mount.
  3. Secure the flash by rotating the hot shoe locking option (8) until it is firmly attached.
  4. Ensure the flash is properly seated and locked to prevent accidental detachment.
NEEWER Z120 SE flash mounted on a camera hot shoe, showing compatibility with various brands

Figure 6: Attaching the Z120 SE to a camera hot shoe.

3. Attaching the Diffuser

For softer, more natural lighting, attach the included diffuser.

  1. Gently slide the diffuser over the flash head until it is securely in place.
NEEWER Z120 SE flash with and without diffuser, demonstrating soft light effect

Figure 7: Z120 SE flash with soft light diffuser attached.

Operation

1. Power ON/OFF

To turn the flash ON or OFF, slide the Power Switch (2) located on the side of the unit.

  • Slide to "OFF" for power off.
  • Slide to "ON" for power on.

2. Selecting Flash Mode

The Z120 SE supports three flash modes: Manual (M), S1, and S2. Press the MODE selection key (4) to cycle through the modes.

Manual (M) Mode

In M mode, you have full control over the flash output. This is ideal for precise lighting control.

  • Press the MODE selection key (4) until "M" is displayed.
  • Use the Power adjustment “-” key (6) and “+” key (7) to adjust the flash output from 1/128 to 1/1 full power in 1/3 stop increments.
Close-up of NEEWER Z120 SE flash display showing M 1/128+0.7

Figure 8: M Mode display and power adjustment buttons.

Power Adjustment Table:

ActionEffect on Flash Output
Short press "+" keyIncreases output (e.g., 1/128, 1/128+0.3, 1/128+0.7, 1/64)
Long press "+" keyIncreases output by full stops (e.g., 1/128 to 1/64)
Short press "-" keyDecreases output (e.g., 1/1, 1/1+0.3, 1/1+0.7, 1/2)
Long press "-" keyDecreases output by full stops (e.g., 1/1 to 1/2)

S1 Mode (Optical Slave)

S1 mode is suitable for manual flash environments. It triggers the Z120 SE synchronously with the first flash from a master flash unit.

  • Press the MODE selection key (4) until "S1" is displayed.
  • The master flash must be set to manual mode.
  • Avoid using master flashes with pre-flash or red-eye reduction functions in S1 mode.

S2 Mode (Optical Slave with Pre-flash Cancellation)

S2 mode is designed for TTL flash environments. It ignores the pre-flash signal from a TTL master flash and synchronizes with the main flash, allowing the master flash to operate in TTL mode.

  • Press the MODE selection key (4) until "S2" is displayed.
  • This mode is also known as "pre-flash cancel mode."
Close-up of NEEWER Z120 SE flash display showing S1/S2 mode

Figure 9: S1/S2 Mode display.

Special Note for S1/S2 Modes: If the Z120 SE (slave light) cannot be synchronized with the master light, please confirm the flash mode of the main control light and correctly set the slave light's induction mode and power output. Avoid using master lights with red-eye reduction, modeling flash, or command/wireless modes (Nikon/Canon) when using S1/S2. Also, avoid using ST-E2 as the flash controller.

3. Test Flash

Press the Test flash key (3) to fire a test flash and check the unit's functionality and light output.

Battery Warning

Improper handling of the battery can lead to serious hazards. Please observe the following:

  1. Do not attempt to detach, modify, or repair the battery by yourself. Any unauthorized operation may cause battery leakage, overheating, burning, and other hazards.
  2. Be sure to use the provided or certified chargers to prevent overcharging and short circuits.
  3. If unusual charging speed or indicator flashing occurs, please stop charging and contact our customer service immediately.
  4. Keep away from flammable and explosive items.

Maintenance

  • Keep the flash unit dry. Do not handle with wet hands.
  • Clean the flash head and body with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
  • Store the flash in a cool, dry place away from direct sunlight and extreme temperatures.
  • If the unit will not be used for an extended period, ensure it is fully charged before storage and periodically recharge it to maintain battery health.
  • Avoid dropping or subjecting the flash to strong impacts.

Troubleshooting

ProblemPossible CauseSolution
Flash not firing
  • Flash unit is OFF.
  • Battery is depleted.
  • Flash not properly mounted on hot shoe.
  • Camera settings incorrect.
  • Ensure power switch is ON.
  • Charge the battery.
  • Re-mount and secure the flash on the hot shoe.
  • Check camera's flash settings.
Flash not synchronizing in S1/S2 mode
  • Master flash mode incompatible (e.g., TTL with S1).
  • Master flash using pre-flash/red-eye reduction.
  • Obstruction between master and slave flash.
  • Ensure master flash is in Manual mode for S1.
  • Ensure master flash is in TTL mode for S2 (S2 ignores pre-flash).
  • Disable pre-flash/red-eye reduction on master flash.
  • Ensure clear line of sight for optical triggering.
Underexposure at bottom of frame
  • Using lenses with focal length longer than 88mm.
  • Use lenses with focal length 88mm or shorter.
  • Adjust flash power or camera ISO/aperture accordingly.
Flash overheating after continuous use
  • Rapid, continuous firing at high power.
  • Allow at least 15 minutes cooling time after 10 full-power flashes.
  • Reduce flash output or frequency of firing.

User Tips

  • Compact and Reliable: Users appreciate the Z120 SE for its compact size and reliable performance, making it a great portable option for various shooting scenarios.
  • Diffuser for Soft Light: Always use the included diffuser for softer, more natural-looking light, especially for portraits, to avoid harsh shadows.
  • Manual Control: Experiment with the manual power settings (1/128 to 1/1) to achieve precise lighting for your creative vision.
  • Optical Slave Modes: Utilize S1 or S2 modes for off-camera flash setups, expanding your lighting possibilities without needing additional triggers. Remember to match the master flash settings accordingly.

Warranty & Support

For any questions or support regarding your NEEWER Basics Z120 SE Mini Camera Flash Speedlite, please contact NEEWER customer service.

  • US Support: +1 732-623-9777
  • Email Support: vip@neewer.com
  • Official Website: www.neewer.com
  • User Manual (PDF): A detailed user manual in PDF format is available for download. Please refer to the official NEEWER website or contact support for the direct link.

Manufacturer Information:
Shenzhen Neewer Technology Co.,Ltd.
Room 1903, Block A, Lu Shan Building No. 3023
Chunfeng Rd Luo Hu District, Shenzhen
Guangdong 518001, China

UK Representative:
Lingfeng Electronic (UK) Ltd
International House, 10 Churchill Way, Cardiff, CF10 2HE, United Kingdom
Email: office.lingfeng@gmail.com

EC Representative:
NW Formations GmbH
Hoferstrasse 9B, 71636 Ludwigsburg, Germany
Email: info.nwformations@gmail.com

NEEWER Brand Overview

Learn more about NEEWER and their range of photography and videography equipment.

Video: An overview of NEEWER's product range, showcasing various lighting and photography accessories.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.