1. Introduction
The Pinmany RZ-FT52A is a CAN Bus Data Converter designed to integrate with Android head units in compatible Toyota vehicles. This device facilitates communication between your vehicle's CAN Bus system and an aftermarket Android car radio, enabling features such as steering wheel controls and other vehicle data to function correctly.
2. Safety Warnings and Precautions
- Operating Voltage: The decoder operates within a voltage range of +9V to +16V. Voltages outside this range (too low or too high) can cause permanent damage to the device.
- Wiring: The product's sockets are 16-pin and 20-pin connectors with a pin pitch of 2.0mm. Always follow the provided pin definition chart strictly for wiring. Improper wiring can damage the CAN Bus decoder and potentially other vehicle electronics.
- Professional Installation Recommended: Installation requires certain professional knowledge, especially concerning vehicle wiring and Android head unit configuration. If you are unsure about the fitting or wiring process, it is highly recommended to seek professional assistance.
- Cables Not Included: This CAN Bus decoder does not include connection cables. Ensure you have suitable cables or purchase a compatible CAN Bus adapter with cables.
3. Specifications
| Feature | Detail |
|---|---|
| Model Name | RZ-FT52A |
| Brand Name | pinmany |
| Manufacturer | Raise |
| Special Features | CAN Bus Data Converter |
| Item Type | Cables, Adapters & Sockets |
| Operating Voltage | 12 V (Range: +9V~+16V) |
| Item Weight | 50g |
| Item Size (L x W x H) | 73.5mm x 46.5mm x 18.5mm (±1mm error due to manual measurement) |
| Material | Black plastic shell |
| Interface | 16-pin / 20-pin PH2.0 connectors |
| Origin | Mainland China |
| Suitable Head Unit | Android 7"/9"/10"/etc. head units with 8-pin connectors and serial communication. |
| Compatible Car Models (Toyota SEA) |
|
4. Installation Guide
The installation process involves physically connecting the CAN Bus decoder and configuring your Android head unit. Ensure the vehicle's power is off before beginning any wiring.
4.1 Physical Connection
- Identify Connectors: Locate the 16-pin and 20-pin CAN plug of your vehicle's wire harness.
- Connect Decoder: Plug the 16-pin and 20-pin plugs from the wire harness into the corresponding sockets on the CAN Bus Box. Refer to the pin definition diagram for correct orientation and wiring.
- Head Unit Compatibility: Ensure your Android head unit has an 8-pin connector for serial communication, as shown in Figure 6.
4.2 Android Head Unit Setup
After physical connection, you need to configure the CAN Bus settings on your Android head unit. The exact steps may vary between different Android head unit models and manufacturers. Consult your head unit vendor's manual if these steps differ.
- Enter Settings: From the Android head unit's main screen, navigate to the "Settings" menu. This might be an icon labeled "Car Settings" or similar.
- Access Factory Settings: Within the settings, look for an option like "Factory" or "Factory Settings".
- Enter Factory Password: You may be prompted to enter a factory password. Common passwords include: 3368, 1617, 8317, 8888. If none of these work, contact your Android radio seller for the correct password.
- Navigate to CAN Bus Settings: Once in the factory settings, find the "CAN Bus setting" or "CAN Related Settings" option.
- Select Manufacturer and Model: In the CAN Bus settings, select "Raise" as the CAN Bus manufacturer. Then, choose your specific Toyota car model and year from the list.
- Save and Reboot: Save the settings and reboot your Android head unit for the changes to take effect.
5. Operation
Once the RZ-FT52A CAN Bus Decoder is correctly installed and configured with your Android head unit, it operates automatically. Its primary function is to translate the vehicle's CAN Bus signals into a format that your Android head unit can understand, enabling the proper functioning of features such as:
- Steering Wheel Controls
- Reverse Gear Detection (for camera activation)
- Vehicle Speed Signal
- Illumination Control
- Door Status Information (if supported by head unit)
No further manual operation of the decoder itself is typically required after initial setup.
6. Maintenance
The RZ-FT52A CAN Bus Decoder is a low-maintenance electronic device. To ensure its longevity and proper function:
- Keep Dry: Avoid exposing the device to moisture or liquids.
- Clean Gently: If cleaning is necessary, use a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
- Avoid Physical Damage: Protect the device from impacts or excessive vibrations.
- Temperature: Operate and store the device within normal automotive temperature ranges.
7. Troubleshooting
If you encounter issues after installing the RZ-FT52A CAN Bus Decoder, consider the following:
- No Functionality (e.g., steering wheel controls not working):
- Check Wiring: Double-check all physical connections to ensure they are secure and correctly wired according to the pin definition diagram (Figure 5). Improper wiring is a common cause of issues.
- Verify Head Unit Settings: Revisit the Android head unit's CAN Bus settings (Section 4.2) to confirm that "Raise" is selected as the manufacturer and your specific car model and year are correctly chosen.
- Head Unit Compatibility: Ensure your Android head unit is compatible (7", 8", 9", 10" units with 8-pin serial communication).
- "Car Name Not Displayed" during setup:
- This indicates a potential compatibility issue or an outdated head unit firmware. Ensure your head unit's software is up to date.
- If your specific car model is not listed in the head unit's CAN Bus settings, the decoder may not be fully compatible with your vehicle's specific CAN protocol.
- Intermittent Functionality:
- Loose connections can cause intermittent issues. Secure all plugs and wires.
- Check for voltage fluctuations. Ensure the vehicle's electrical system is stable and within the decoder's operating voltage range (+9V~+16V).
8. User Tips
- Verify Car Model Compatibility: While a list of compatible Toyota models is provided, always double-check if your exact model and year are supported by the decoder and your Android head unit's CAN Bus settings. For example, if you have a Toyota Land Cruiser Prado 120 from 2007, confirm its compatibility with the seller before installation, as the listed models are generally newer.
- Consult Head Unit Manual: The setup process on the Android head unit can vary. Always refer to your specific head unit's instruction manual for detailed steps on accessing factory settings and CAN Bus configuration.
- Take Photos: Before disconnecting any wires, take clear photos of your existing wiring. This can be invaluable for reference during installation or troubleshooting.
9. Warranty and Support
For any questions, technical support, or assistance with installation or troubleshooting, please contact the seller directly. Provide your product model (RZ-FT52A) and a detailed description of your issue, including your vehicle's make, model, year, and the Android head unit model you are using.
The manufacturer, Raise, and the brand, Pinmany, are committed to providing support for their products.
