1. Introduction
Thank you for choosing the Bileeko Car Backup Rear View Parking Camera. This multi-functional camera is designed to enhance your driving safety by providing clear, multi-angle views around your vehicle. Featuring a 360° adjustable lens, full-color night vision, and CVBS compatibility, it offers a reliable solution for parking and monitoring blind spots. This manual provides essential information for the proper installation, operation, and maintenance of your camera.
2. Safety Information
- Always ensure the vehicle's engine is off and the parking brake is engaged before beginning installation.
- Disconnect the vehicle's battery before performing any electrical work to prevent short circuits or electrical shock.
- Route all cables carefully to avoid interference with vehicle controls, moving parts, or sharp edges.
- Do not obstruct the driver's view or interfere with airbag deployment.
- Consult a professional if you are unsure about any part of the installation process.
- This camera is an aid for safe driving and parking; it does not replace the driver's responsibility to check surroundings.
3. Product Overview
Key Features:
- 360° Adjustable Lens: Allows rotation to capture front, rear, left, or right views for comprehensive vehicle monitoring.
- Full Color Night Vision + 2 LEDs: Enhances visibility in low-light conditions with vivid color imaging and dual LED illumination. Features 6 layers of lenses for clearer vision at night.
- CVBS Compatibility: Works seamlessly with CVBS-supported car displays (e.g., MP5/Android multimedia players). Note: Monitor is not included.
- Dual Mode Options:
- White Wire: Default with ruler guide. Cut the white wire to disable the ruler guide.
- Green Wire: Default mirrored image. Cut the green wire to switch to a normal (non-mirrored) image.
- CCD Sensor: Delivers sharper, distortion-free imaging compared to standard CMOS cameras.
Components:
- 1x Multi-function Car Camera
- Installation Accessories (wiring not included)
- Video Cable
- Control Wires (Front/Rear View, Control Ruler line)
4. Installation
4.1 Choosing an Installation Location
The camera can be installed in various locations depending on the desired view (front, rear, or side). Common locations include:
- Rear View: Above the license plate, near the trunk handle, or integrated into the bumper.
- Front View: On the front grille, below the bumper, or near the front emblem.
- Side View: Underneath the side mirrors.
4.2 Mounting the Camera
The camera supports easy and non-destructive installation, typically using special double-sided adhesive for high-strength paste, avoiding the need for drilling or punching holes in your vehicle.
- Clean the chosen mounting surface thoroughly to ensure it is free of dust, grease, and moisture.
- Peel off the protective backing from the double-sided adhesive on the camera base.
- Carefully position the camera and press firmly to secure it to the surface.
- Ensure the camera lens is facing the desired direction and has a clear, unobstructed view.
4.3 Wiring Diagram
Connect the camera to your car's electrical system and CVBS-compatible monitor (e.g., MP5/Android multimedia player) as shown in the diagram below. Please note that specific wiring harnesses are not included and may need to be purchased separately.
Monitor → Image Switcher → Camera → Power
The camera includes specific control wires for functionality:
- White Wire: Controls the parking ruler guide. Cut this wire to disable the ruler guide.
- Green Wire: Controls image mirroring. Cut this wire to switch from a mirrored image (default for rear view) to a normal image (suitable for front view).
5. Operation
5.1 Adjusting the Lens Angle
The camera features a 360° rotatable lens, allowing you to manually adjust the viewing angle to suit your needs. It also supports a 90° vertical adjustment.
- Gently rotate the lens housing to achieve the desired horizontal view.
- Tilt the lens up or down to adjust the vertical angle.
- Ensure the lens is securely positioned after adjustment to maintain a stable view.
5.2 Activating Night Vision
The camera is equipped with full-color night vision and two integrated LEDs for enhanced visibility in low-light conditions. The automatic induction light ensures optimal illumination when needed.
5.3 Switching Display Modes (Ruler Guide / Image Mirroring)
To change the display mode (e.g., enable/disable parking lines or switch between mirrored/normal image), you must cut the corresponding control wire and then re-power the camera. This action is permanent for the current setup.
- For Parking Ruler Guide: Locate the white control wire. If you wish to disable the ruler guide, carefully cut this wire.
- For Image Mirroring: Locate the green control wire. If you wish to switch from a mirrored image (typical for rear cameras) to a normal image (typical for front cameras), carefully cut this wire.
- After cutting the desired wire, disconnect the camera's power supply for a few seconds, then reconnect it to apply the change.
6. Maintenance
- Cleaning the Lens: Regularly clean the camera lens with a soft, damp cloth to ensure a clear view. Avoid abrasive cleaners or materials that could scratch the lens.
- Checking Connections: Periodically inspect all wiring connections to ensure they are secure and free from corrosion or damage.
- Mounting Security: Verify that the camera remains firmly attached to its mounting surface. Reapply adhesive if necessary.
- Environmental Protection: While designed for outdoor use, extreme weather conditions (e.g., heavy snow, ice, or prolonged direct sunlight) may affect performance. Ensure the camera is free from obstructions like dirt or ice.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No image on monitor |
|
|
| Image is distorted or unclear |
|
|
| Parking lines are missing/present incorrectly |
|
|
| Image is mirrored/not mirrored incorrectly |
|
|
8. Specifications
| Feature | Specification |
|---|---|
| Brand | Bileeko |
| Origin | Mainland China |
| Sensor Type | CCD |
| Lens Layers | 6 layers for clearer vision |
| Lens Adjustability | 360° Rotatable, 90° Vertical Adjustment |
| Night Vision | Full Color with 2 LEDs and Automatic Induction Light |
| Compatibility | CVBS Car Monitors (MP5/Android Multimedia Players) |
| Dimensions (approx.) | Height: 3.8 cm (1.5 inches), Width: 5 cm (1.97 inches) |
| Package Weight (approx.) | 0.167 kg |
| Package Dimensions (approx.) | 13 cm (L) x 8 cm (W) x 6 cm (H) |
9. User Tips
- For optimal night vision, ensure the camera lens is clean and free from obstructions.
- When deciding whether to cut the control wires, consider your primary use case (e.g., rear view typically uses mirrored image and parking lines, front view typically uses normal image and no parking lines).
- Always test the camera's functionality and view angles after installation and before driving.
10. Warranty and Support
For any questions, technical support, or warranty inquiries, please contact the seller or manufacturer directly through your purchase platform. Keep your purchase receipt as proof of purchase.