1. Product Overview
The Bileeko Multi-Function Car Camera is designed to provide enhanced visibility for your vehicle, featuring a 170° Fisheye Lens and switchable AHD-1080P/CVBS video output. It supports various viewing modes including rear, front, and side views, making parking and maneuvering safer and easier.
Figure 1: Bileeko Multi-Function Car Camera highlighting Full HD 1080p, AHD/CVBS compatibility, and control wires.
Figure 2: Illustrates the wide 170° Fisheye Lens view provided by the camera.
2. Specifications
| Feature | Specification |
|---|---|
| Lens Material | Plastic + Glass |
| Video Cable Length | 6M |
| Connection Type | Wire |
| Alarm Type | Vehicle Backup Cameras, Front, Front Side, Rear Side |
| Viewing Angle | 170° |
| Guiding Line | Yes (Adjustable) |
| Video Output | AHD-1080P / CVBS (Switchable) |
| Certifications | CE, FCC, RoHS |
| Dimensions (approx.) | 4.1cm (length) x 2.1cm (width) x 1.5cm (height) |
Figure 3: Detailed dimensions of the camera module.
3. Setup and Installation
3.1 Physical Installation
Choose a suitable location for your camera, typically at the rear of the vehicle for backup, or front/side for other viewing angles. Ensure the camera has a clear line of sight and is securely mounted.
Figure 4: General installation points for the camera and monitor in a vehicle.
3.2 Wiring Diagram
Follow the wiring diagram carefully to connect the camera to your car's power supply and monitor.
- Connect the yellow RCA video output cable from the camera to the video input (e.g., 'Video In' or 'Reverse/BACK') on your car monitor.
- Connect the camera's power cable (red and black wires) to your vehicle's reversing light positive (+) and ground (GND) respectively.
- The red trigger wire, often integrated with the video cable, should be connected to the reversing light positive (+) and also to the 'reverse-in' or 'trigger' cable on your monitor. This signals the monitor to switch to the camera view when reverse gear is engaged.
Figure 5: Detailed wiring connections for the camera, including signal and parking line control wires.
3.3 Signal Configuration (AHD-1080P / CVBS)
The camera supports both AHD-1080P and CVBS video formats. AHD-1080P offers a clearer image but requires an AHD-1080P compatible monitor. If your monitor does not support AHD-1080P, you must switch the camera to CVBS mode.
- Default: AHD-1080P output.
- To switch to CVBS: Locate the orange wire loop on the camera's cable. Cut this orange loop to change the output to CVBS.
Figure 6: Instructions for cutting the orange wire to switch between AHD and CVBS video formats.
After connecting the camera, you may need to configure your car monitor's settings:
- Navigate to your monitor's Factory Settings.
- Find the Backcar Setting or similar option.
- Select the appropriate signal format: CVBS-NTSC or AHD-1080P.
Important: If AHD-1080P cannot be selected in your monitor's settings, your monitor does not support AHD cameras. Ensure you have switched the camera to CVBS mode by cutting the orange wire.
Figure 7: Example of monitor settings for selecting the camera's video input format.
4. Operating the Camera
4.1 Switching View Modes (Rear/Front)
The camera can function as either a rear-view or front-view camera. This is controlled by the green wire loop.
- Default: Rear view (mirror image).
- To switch to Front View: Locate the green wire loop on the camera's cable. Cut this green loop to change the view to front view (non-mirror image).
4.2 Parking Guidelines
The camera comes with active parking guidelines by default. You can disable these if preferred using the white wire loop.
- Default: Parking guidelines active.
- To disable guidelines: Locate the white wire loop on the camera's cable. Cut this white loop to deactivate the parking guidelines.
Figure 8: Instructions for cutting the green wire (Front/Rear view) and white wire (parking guidelines).
5. Maintenance
To ensure optimal performance and longevity of your Bileeko Car Camera, follow these simple maintenance tips:
- Cleaning: Regularly clean the camera lens with a soft, damp cloth to remove dirt, dust, or water spots that may obstruct the view. Avoid abrasive cleaners.
- Connection Check: Periodically inspect all wiring connections to ensure they are secure and free from corrosion. Loose connections can lead to signal loss or intermittent operation.
- Environmental Protection: While the camera is designed for outdoor use, extreme weather conditions (e.g., heavy snow, ice, or prolonged direct sunlight) can affect performance. Ensure the camera is properly sealed and protected during installation.
6. Troubleshooting
6.1 No Signal or Gray Screen
If the rear view camera is connected but the display shows a gray screen with no signal or image, consider the following steps:
- Verify Signal Format: Ensure the camera's output signal (AHD-1080P or CVBS) matches your monitor's input capabilities. If your monitor is not AHD-1080P compatible, make sure the orange wire loop on the camera cable has been cut to switch to CVBS.
- Check Connections: Confirm all wiring connections are correct and secure. The red trigger wire must be properly linked to your vehicle's reverse light positive and the monitor's reverse-in cable.
- AUX-IN Connection: If your monitor supports an AUX-IN port, try connecting the camera's video output to this port.
- Correct Signal Standard: Selecting an incorrect signal standard (e.g., PAL instead of NTSC for CVBS) can result in a monochrome display. Ensure you choose the correct standard for your camera (CVBS adheres to NTSC, AHD1080P is supported). After changing the standard, restart the camera's power.
6.2 Image Quality Issues
- Fuzzy or Unclear Image: Clean the camera lens. Check for any obstructions. Ensure the signal format is correctly set for your monitor (AHD is generally clearer than CVBS).
- Incorrect View (Mirror/Non-Mirror): If the image is mirrored when it should be normal, or vice-versa, check the green wire loop. Cut it to toggle between rear (mirror) and front (non-mirror) views.
- Missing Parking Lines: If parking guidelines are not displayed, check the white wire loop. Ensure it is in the desired state (cut to disable, intact to enable).
7. User Tips
- Test Before Final Installation: Before permanently mounting the camera and routing all cables, perform a temporary setup to test all functions (view modes, guidelines, signal compatibility) to ensure everything works as expected.
- Cable Management: Use cable ties and protective conduits to neatly route and secure all wiring, preventing damage from heat, sharp edges, or moving parts.
- Monitor Compatibility: Always confirm your car monitor's compatibility with AHD-1080P or CVBS signals before installation. This is the most common cause of 'no signal' issues.
8. Warranty and Support
For warranty information or technical support, please refer to the seller's policies or contact the retailer where you purchased the product. Keep your proof of purchase for any warranty claims.