DAKEFPV F722 8S 70A Stack

Contents

DAKEFPV F722 Flight Controller and 70A ESC Stack Instruction Manual

Model: F722 8S 70A Stack

Product Overview

The DAKEFPV F722 Flight Controller and 70A ESC Stack is a high-performance electronic system designed for FPV racing drones and other remote control aircraft. It integrates an F722 Flight Controller (FC) and a 70A 4-in-1 Electronic Speed Controller (ESC) into a compact 30x30mm stack. This system offers advanced features for precise flight control and robust power delivery.

Video: DAKEFPV F722 8S 70A Stack Product Overview

DAKEFPV F722 Flight Controller and 70A ESC Stack assembled, with individual components

Image: Assembled F722 Flight Controller and 70A ESC Stack with individual components.

Package Contents

The package typically includes the following components:

Package contents for DAKEFPV F722 70A 30x30 Stack

Image: Package contents for DAKEFPV F722 70A 30x30 Stack.

Option 1 - DAKEFPV F722 70A 30x30 STACK

  1. DAKEFPV F722 Flight Controller x 1
  2. DAKEFPV BLS 70A 4 in 1 ESC x 1
  3. 35V 1000uF Low ESR Capacitor x 1
  4. M3 Nylon Nut x 5
  5. M3 silicone O Ring x 5
  6. M3*8mm Silicone Grommets (for FC) x 1
  7. M3*8.1mm Silicone Grommets (for ESC) x 1
  8. SH 1.0mm 25mm-length 8pin Cable (for FC-ESC connection) x 1
  9. SH 1.0mm 75mm-length 8pin Cable* x 1
  10. M3*30mm Inner-hexagon Screws x 5
  11. GPS 6pin cable, Analog VTX 6pin cable, dual-camera 6pin cable x 1
  12. XT60 Power Cable (70mm) x 1

* When the ESC tail faces the drone's front, use this cable for the flight controller and ESC; both ends plug interchangeably.

Option 2 - DAKEFPV F722 70A 30x30 FC (Flight Controller Only)

  1. DAKEFPV H743 Flight Controller x 1
  2. Silicone Grommets (random colors) x 8, hexagon screws x 5, hexagon nuts x 5, silicone rings x 5
  3. FC 12-pin to ESC 8-pin cable, LED/buzzer 4-pin cable x 1
  4. GPS 6-pin cable, analog VTX 6-pin cable, dual-camera 6-pin cable x 1, receiver 4-pin cable

Option 3 - DAKEFPV 8S 70A 4 in 1 ESC (ESC Only)

  1. DAKEFPV 8S 70A 4 in 1 ESC x 1
  2. 35V 1000uF Low ESR Capacitor (Buy 12S ESC Send 63V1000uF Capacitor)
  3. FC 12-pin to ESC 8-pin cable (for connecting FC to ESC)
  4. XT60 x 1

Specifications

Specifications table for DAKE F722 Flight Controller

Image: Detailed specifications for the DAKE F722 Flight Controller.

DAKE F722 Flight Controller Specifications
FeatureDescription
Product NameDAKE F722 30 x 30 Flight Controller
Main Control ChipSTM32F722
GyroscopeICM42688P
USB Interface TypeType-C
BarometerBuilt-in
OSD ChipAT7456E
Bluetooth BLENot supported
WiFiNot supported
DJI Air Unit ConnectionSupports 6-pin plug-in and soldering connection
6-pin DJI Air Unit PlugCompatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1 without wiring changes
FLASH (Black Box)16MB onboard FLASH
Current MeterSupported
Input Voltage3-12S LiPo battery
UART Serial Ports8 groups
Buzzer PadsSupports BZ+ and BZ- pads, connect 5V active buzzer

ESC Specifications (BLS 70A 4-in-1)

  • Continuous Current: 70A per channel (total 220A for four channels)
  • Peak Current: 280A for 10 seconds
  • Input Voltage: 3-8S LiPo
  • PCB: 3 ounces copper thickness
  • MOS Tube: Upgraded for higher specification
  • Heat Dissipation: New aluminum alloy heat sink for quick heat dissipation

Dimensions

Dimensions of the F722 Flight Controller and the assembled stack

Image: Dimensions of the F722 Flight Controller and the assembled stack.

  • Flight Controller Size: 36mm x 36mm
  • Mounting Holes: 30.5mm x 30.5mm
  • Stack Height: 15.8mm (assembled)

Setup and Installation

Important Stack Installation Note

Important Stack Installation Note regarding silicon pads and short circuits

Image: Important installation guidelines for the FC/ESC stack.

When installing your stack, adhere to the standard mounting method. The orientation of the gyro and motor sequence can be adjusted through settings. If you opt for an inverted manner, be extra careful about the space between the frame, the FC, and the ESC.

It's critical to swap the silicon pads when changing the positions of the FC and the ESC, as illustrated below. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Please be aware that any damage resulting from improper installation of this nature is not covered under the Warranty.

Wiring Diagram

Comprehensive wiring diagram for the F722 stack

Image: Comprehensive wiring diagram for the F722 stack, showing connections for FC, ESC, motors, LED, USB, GPS, ELRS, and VTX.

The FC and ESC can also be connected via direct soldering. Refer to the image below for soldering pad definitions.

Soldering pads definition for direct soldering

Image: Soldering pads definition for direct soldering connections.

Connecting to DJI Air Units

The F722 Flight Controller features a DJI air unit direct plug interface, fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1. No wiring changes are needed for these units.

Cable connection for DJI O3 Air Unit

Image: Cable connection for DJI O3 Air Unit.

Cable connection for DJI Air Unit V1

Image: Cable connection for DJI Air Unit V1.

ELRS Receiver Connection

When using an ELRS receiver, the SBUS signal wire of the receiver must be connected to the SBUS pad on the front side of the flight controller (this pad internally uses UART2).

If you are also using the DJI Air Unit (O3/Link/Vista/Air Unit V1), you will need to disconnect the SBUS signal wire from the Air Unit harness. Failure to do so will prevent the SBUS receiver from being properly recognized by the flight controller. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.

Important notice for ELRS receiver connection, specifically regarding SBUS signal wire

Image: ELRS receiver connection and SBUS signal wire management.

Motor Support

The flight controller supports up to 8 motors, making it suitable for X8, Y6, fixed-wing, and other aircraft models that require more than 4 motors.

F722 Flight Controller supporting 8 motors (M1-M8)

Image: F722 Flight Controller motor output pads (M1-M8).

Operating Instructions

Battery Capacity Indicator

The flight controller features a 4-level battery capacity indicator. Once the battery is connected, you can instantly see the battery level, eliminating the need for an external LiPo checker.

Battery capacity indicator on F722 Flight Controller

Image: F722 Flight Controller with integrated battery capacity indicator.

LED Light Bar Control

The LED pads at the corners of the flight controller allow you to connect and control LED light strips. A single press of the BOOT button lets you switch between different lighting modes. A long press of the BOOT button switches to the onboard LED light effect control mode, and short presses toggle between various preset light effects.

LED light bar pad connection and BOOT button functionality

Image: LED light bar connection pads and BOOT button for control.

Firmware and Configuration

The F722 Flight Controller uses BetaFlight firmware for computer parameter adjustment. It supports 8 motors and 4 servos, and is equipped with a 16MB onboard FLASH memory black box for continuous recording of flight status (sensor data, control commands, fault codes). This data can be retrieved for accident analysis.

More features of the F722 stack, including barometer, black box flash, DJI Air Unit direct plug, 8 UARTs, dual-channel BEC

Image: Overview of additional features including Black Box Flash and Barometer.

Maintenance

Regular inspection of all connections and components for wear or damage is recommended. Ensure all screws are tightened appropriately and wiring is secure to prevent disconnections during flight.

Keep the flight controller and ESC clean and free from dust or debris. Avoid exposing the components to moisture or extreme temperatures.

Troubleshooting

Preventing Voltage Spikes and Burnout

To prevent the stack from being burnt out by voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor included in the package. This capacitor helps filter out signal interference and smooth power delivery to the flight controller's gyroscope.

Recommendation to use Low ESR capacitor to prevent burnout from voltage spikes

Image: Explanation of TVS diode and filter capacitors for voltage spike protection.

ELRS Receiver Not Recognized

If your ELRS receiver is not recognized, especially when also using a DJI Air Unit, ensure the SBUS signal wire from the Air Unit harness is disconnected. This wire can interfere with the FC's recognition of the ELRS receiver. Carefully remove or cut this wire and insulate the exposed end.

User Tips

  • Proper Installation: Always double-check the orientation of the FC and ESC, and ensure silicon pads are correctly placed to avoid short circuits, especially around the USB port.
  • Capacitor Use: For optimal performance and protection against voltage spikes, always install the provided Low ESR capacitor.
  • Firmware Updates: Regularly check for and apply BetaFlight firmware updates to ensure you have the latest features and bug fixes.
  • Wiring Cleanliness: Keep your wiring as neat and tidy as possible to prevent interference and make troubleshooting easier.

Warranty and Support

Please note that any damage resulting from improper installation, such as short circuits due to incorrect silicon pad placement or wiring errors, is not covered under the product warranty.

For technical support, troubleshooting assistance beyond this manual, or warranty claims, please contact the seller or manufacturer directly with your purchase details.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.