Geely 1016056847

Contents

Geely Engine Oil Filter Instruction Manual

Part Number: 1016056847

Introduction

This manual provides essential information for the proper installation, maintenance, and troubleshooting of your new Geely Engine Oil Filter, Part Number 1016056847. This high-quality oil filter is designed for specific Geely models, including the New Emgrand GS 1.3T, Vision X3, Binyue, Coolray X3, Binrui S1, and GL Engine 1.4T. Regular oil filter replacement is crucial for maintaining engine health and performance.

Safety Information

Always prioritize safety when working on your vehicle. Ensure the engine is cool before starting any work. Wear appropriate personal protective equipment, such as gloves and eye protection. Refer to your vehicle's service manual for specific safety precautions and procedures.

Package Contents

Your package should contain the following item:

  • 1 x Geely Engine Oil Filter (Part Number: 1016056847)
Geely Engine Oil Filter and packaging
Image: Geely Engine Oil Filter (Part No. 1016056847) and its original packaging.
Geely Engine Oil Filter with part number visible on box
Image: Close-up of the Geely Engine Oil Filter and box, highlighting the part number 1016056847 and "OIL FILTER ASSY." label.

Installation Instructions

Replacing an engine oil filter typically involves the following steps. Always consult your vehicle's specific service manual for detailed instructions and torque specifications.

  1. Prepare the Vehicle: Park the vehicle on a level surface and engage the parking brake. Allow the engine to cool completely.
  2. Locate the Oil Filter: Refer to your vehicle's manual to find the exact location of the oil filter.
  3. Drain Engine Oil: Place a suitable drain pan under the oil pan. Remove the oil drain plug and allow all the old engine oil to drain completely.
  4. Remove Old Oil Filter: Position the drain pan under the old oil filter. Use an oil filter wrench to loosen and remove the old filter. Be prepared for residual oil to spill.
  5. Prepare New Oil Filter: Apply a thin film of new engine oil to the rubber gasket of the new Geely oil filter. This ensures a proper seal.
  6. Install New Oil Filter: Hand-tighten the new oil filter onto the engine until the gasket makes contact with the engine block. Then, tighten it an additional 3/4 to 1 full turn, or according to your vehicle's specifications. Do not overtighten.
  7. Replace Drain Plug: Reinstall the oil drain plug with a new washer (if required) and tighten it to the manufacturer's specified torque.
  8. Refill Engine Oil: Add the recommended type and quantity of new engine oil to your vehicle's engine.
  9. Check for Leaks: Start the engine and let it run for a few minutes. Turn off the engine and check for any oil leaks around the new filter and drain plug. Check the oil level and top up if necessary.
Top view of Geely Engine Oil Filter
Image: Top view of the Geely Engine Oil Filter, showing the threaded opening and gasket surface.

Operating Instructions

Once the new oil filter is installed and the engine oil has been refilled, the filter operates automatically as part of your engine's lubrication system. The primary "operation" for the user is to monitor for proper function after installation:

  • After installation, drive the vehicle for a short period and then re-check the oil level and inspect for any leaks.
  • Ensure the oil pressure warning light on your dashboard turns off shortly after starting the engine. If it remains on, turn off the engine immediately and investigate the cause.

Maintenance

The engine oil filter is a consumable component and requires periodic replacement. Refer to your vehicle's owner's manual or service schedule for the recommended oil and filter change intervals. Typically, oil filters are replaced every time the engine oil is changed, which can range from every 5,000 to 15,000 miles (or 8,000 to 24,000 kilometers), depending on the vehicle, oil type, and driving conditions.

Troubleshooting

If you encounter issues after replacing your oil filter, consider the following common problems and solutions:

Problem Possible Cause Solution
Oil Leak from Filter Area
  • Old gasket stuck to engine block
  • Gasket not properly lubricated
  • Filter not tightened sufficiently
  • Filter overtightened (damaged gasket)
  • Incorrect filter size/type
  • Ensure old gasket is removed before installing new filter.
  • Apply a thin film of new oil to the new filter's gasket.
  • Tighten filter by hand, then 3/4 to 1 full turn. Do not overtighten.
  • Verify the filter is the correct part number for your vehicle.
Oil Pressure Warning Light On
  • Low engine oil level
  • Incorrect filter installation
  • Faulty oil pressure sensor
  • Check engine oil level and add oil if necessary.
  • Re-check filter installation for proper seating and tightness.
  • If problem persists, consult a qualified mechanic.

Specifications

Feature Detail
Part Number 1016056847
Brand Geely
Compatibility Geely New Emgrand GS 1.3T, Vision X3, Binyue, Coolray X3, Binrui S1, GL Engine 1.4T
High-concerned chemical None
Manufacturer Part Number 0
Interchange Part Number 0
OEM NO. 0
Country/Region of Manufacture Hubei, Mainland China
Package Dimensions (approx.) Length: 30 cm, Width: 20 cm, Height: 10 cm
Package Weight (approx.) 0.68 kg

User Tips

  • Always use the correct type and viscosity of engine oil recommended by your vehicle manufacturer.
  • Ensure the engine is completely cool before attempting an oil and filter change to prevent burns.
  • Dispose of used oil and filters responsibly at an authorized recycling center.

Support

For further assistance or inquiries regarding this product, please contact the seller directly through the platform where the purchase was made. Provide your order details and the product part number (1016056847) for efficient support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.