Homcom Modern Floor Lamp Instruction Manual

Introduction

Thank you for purchasing the Homcom Modern Floor Lamp. This lamp is designed to add elegance and warmth to your home with its modern design, golden steel structure, and synthetic linen lampshade. It provides soft, welcoming light, ideal for reading or relaxing in various settings such as living rooms, bedrooms, or offices. This manual provides detailed instructions for assembly, operation, maintenance, and troubleshooting to ensure safe and efficient use of your new floor lamp.

Safety Information

Ensure the lamp is unplugged before assembly, cleaning, or changing the bulb.
Do not exceed the maximum wattage specified for the bulb (40W).
Keep the power cord away from heat sources, sharp edges, and wet areas.
Do not operate the lamp with a damaged cord or plug.
Place the lamp on a stable, level surface to prevent tipping.
This lamp is for indoor use only.
Keep out of reach of children and pets to prevent accidental tipping or damage.

Package Contents

Please check the package to ensure all components are present and undamaged:

Lamp Base
Lamp Pole (sections if applicable for assembly)
Curved Arm
Lampshade (Synthetic Linen)
Power Cord with Foot Switch
Assembly Hardware (screws, washers, etc., if required)
Instruction Manual (this document)

Note: An E27 bulb is NOT included and must be purchased separately.

Setup and Assembly

Assembly is required for this floor lamp. Follow these steps carefully:

Unpack all components and lay them out on a clean, flat surface.
Attach the lamp pole sections together, ensuring they are securely tightened.
Secure the lamp pole to the lamp base. Ensure the base is stable and the pole is upright.
Attach the curved arm to the top of the lamp pole.
Carefully place the synthetic linen lampshade onto the lamp holder assembly. Secure it if there are any retaining rings or clips.
Insert an E27 bulb (not included) into the lamp holder. Ensure the bulb does not exceed the maximum wattage of 40W.
Position the lamp in your desired location, ensuring the power cord can reach an AC outlet without being stretched or obstructed.

Diagram showing the dimensions of the Homcom Modern Floor Lamp — Figure 1: Lamp dimensions for proper placement. Total height: 163.5 cm, Shade diameter: 38 cm, Shade height: 24 cm, Base diameter: 26 cm, Base height: 2.5 cm.

Image showing compatible bulb types for the E27 lamp holder — Figure 2: Compatible bulb types for the E27 socket. Note: Bulb is not included. Compatible with dimmable, low consumption, LED, and halogen bulbs.

Operating Instructions

The Homcom Modern Floor Lamp is designed for simple operation.

Once assembled and a bulb is installed, plug the power cord into a standard AC electrical outlet (220-240V/50Hz).
Locate the foot switch on the power cord.
Press the foot switch to turn the lamp ON.
Press the foot switch again to turn the lamp OFF.

Close-up of the foot switch on the power cable — Figure 3: The convenient foot switch allows for easy operation without bending down. The long power cable provides flexible placement options.

Maintenance

Regular maintenance will help prolong the life and appearance of your lamp.

Cleaning: Ensure the lamp is unplugged before cleaning. Wipe the metal parts with a soft, dry cloth. For the synthetic linen lampshade, gently dust with a soft brush or vacuum with a brush attachment. Do not use abrasive cleaners or solvents.
Bulb Replacement: Always unplug the lamp before replacing the bulb. Allow the old bulb to cool completely before removing it. Screw in a new E27 bulb, ensuring it does not exceed 40W.

Troubleshooting

Problem	Possible Cause	Solution
Lamp does not turn on.	Lamp is not plugged in. Bulb is loose or burnt out. Power outlet is not working. Foot switch is faulty.	Ensure the lamp is securely plugged into a working outlet. Tighten or replace the E27 bulb (max 40W). Test the outlet with another appliance. Contact customer support if the switch is suspected to be faulty.
Lamp flickers.	Bulb is loose or incompatible. Voltage fluctuations.	Tighten the bulb. Ensure it is a compatible E27 bulb. Check other electrical devices for similar issues; consult an electrician if necessary.
Lamp is unstable.	Assembly not fully tightened. Placed on an uneven surface.	Re-check all connections and tighten securely. Move the lamp to a flat, stable surface.

Specifications

Model	B31-329V90GD
Color	White and Gold
Material	Steel, Synthetic Linen (100% Polyester)
Overall Dimensions (L x W x H)	64 x 38 x 163.5 cm
Shade Dimensions (Diameter x Height)	Ø38 x 24 cm
Base Dimensions (Diameter x Height)	Ø26 x 2.5 cm
Cable Length	1.9 m
Lamp Holder Type	E27
Maximum Power	40W
Voltage	220-240V / 50Hz
Installation Method	Self-contained (Floor Lamp)
Luminous Flux	249-2000 Lumens (depending on bulb)
Power Source	AC

User Tips

For optimal lighting, choose an E27 LED bulb with a color temperature that suits your room's ambiance (e.g., warm white for relaxation, cool white for reading).
The long power cable offers flexibility; use cable clips or ties to manage excess cable and prevent tripping hazards.
Consider placing the lamp in a corner or beside a sofa to maximize its decorative and functional appeal without obstructing walkways.

Warranty and Support

This product comes with a standard manufacturer's warranty. For specific warranty details, claims, or technical support, please refer to the documentation provided at the time of purchase or contact the seller directly. Keep your proof of purchase for any warranty-related inquiries.

HOMCOM B31-329V90GD