1. Introduction
This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your JASIC WSME-200 (E201II) Pulse AC/DC TIG Welder. Please read this manual thoroughly before operating the machine to ensure proper usage and to prevent injury or damage.
The JASIC WSME-200 (E201II) is a versatile inverter IGBT welding machine designed for TIG welding of various metals including carbon steel, stainless steel, and aluminum alloys. It features both AC and DC output, pulse functionality, and a user-friendly control panel.
2. Safety Information
Welding can be dangerous. Always follow safety precautions to prevent electric shock, burns, fire, and other hazards. This section outlines general safety guidelines. Refer to local safety regulations and standards for comprehensive safety practices.
- Always wear appropriate personal protective equipment (PPE), including a welding helmet with proper shade, flame-resistant clothing, welding gloves, and safety shoes.
- Ensure the welding area is well-ventilated to avoid inhaling welding fumes.
- Never weld near flammable materials or in explosive atmospheres.
- Ensure the machine is properly grounded.
- Do not touch live electrical parts.
- Disconnect power before performing any maintenance or service.
- Keep children and unauthorized personnel away from the welding area.
- Use only genuine replacement parts and accessories.
3. Package Contents
Upon unpacking, please verify that all items listed below are present and undamaged:
- JASIC WSME-200 (E201II) TIG Welder Unit
- TIG Torch
- Earth Clamp
- User Manual
- Consumables (e.g., collets, collet bodies, ceramic nozzles, tungsten electrodes)

4. Product Overview
Familiarize yourself with the main components and connections of the WSME-200 welder.
4.1 Front Panel

- Digital Display: Shows welding current, voltage, and other parameters.
- Control Knobs: Adjust welding parameters such as current, pulse frequency, AC balance, etc.
- Mode Selection Buttons: For selecting welding method (TIG AC/DC, Pulse), operation mode, etc.
- Gas Output Connector: For inert gas supply to the TIG torch.
- TIG Torch Connector: Connects the TIG torch.
- Earth Clamp Connector: Connects the earth clamp.
4.2 Rear Panel

- Power Switch: Turns the machine ON/OFF.
- AC-220V Input: Power supply connection point.
- Cooling Fan: Ensures proper ventilation and cooling during operation.
- Gas Input: Connects to the inert gas cylinder (e.g., Argon).
5. Setup
Follow these steps to set up your JASIC WSME-200 TIG Welder for operation.
- Placement: Place the welder on a stable, level surface in a well-ventilated area, away from dust, moisture, and direct sunlight. Ensure adequate space around the machine for cooling.
- Power Connection:
- Ensure the power switch on the rear panel is in the "OFF" position.
- Connect the welder's power cord to a suitable 220V AC power outlet. Verify that the power supply meets the machine's requirements (see Specifications).
- Gas Connection:
- Connect the gas hose from your inert gas cylinder (e.g., Argon) to the gas input connector on the rear panel of the welder.
- Connect the other end of the gas hose to a gas regulator on your gas cylinder. Ensure all connections are tight to prevent leaks.
- Open the gas cylinder valve and set the desired gas flow rate using the regulator.
- TIG Torch Connection:
- Connect the TIG torch cable to the TIG torch connector on the front panel.
- Ensure the torch's gas line is also properly connected to the welder's gas output.
- Install the appropriate tungsten electrode, collet, collet body, and ceramic nozzle into the TIG torch head.
- Earth Clamp Connection:
- Connect the earth clamp cable to the earth clamp connector on the front panel.
- Securely attach the earth clamp to the workpiece or welding table, ensuring good electrical contact.
6. Operating Instructions
This section provides general guidance for operating the WSME-200 TIG Welder. Specific welding parameters will vary based on material, thickness, and desired weld quality.
- Power On: Flip the power switch on the rear panel to the "ON" position. The digital display should illuminate.
- Select Welding Mode: Use the mode selection buttons on the front panel to choose between AC TIG (for aluminum) or DC TIG (for steel, stainless steel, copper, titanium, nickel). Select Pulse mode if desired.
- Set Welding Parameters:
- Welding Current: Adjust the main current knob to the desired amperage for your material thickness.
- Gas Pre-flow/Post-flow: Set the pre-flow and post-flow times for shielding gas.
- Pulse Parameters (if applicable): If using Pulse TIG, adjust pulse frequency, peak current, base current, and pulse width as needed.
- AC Balance (if applicable for AC TIG): Adjust AC balance for cleaning action and penetration when welding aluminum.
- Arc Start: Choose between High-Frequency (HF) or Lift TIG arc starting. HF is generally preferred for TIG.
- Perform Test Weld: Before welding your actual workpiece, perform a test weld on a scrap piece of the same material to fine-tune your settings.
- Welding Process:
- Hold the TIG torch at the correct angle (typically 70-75 degrees) to the workpiece.
- Initiate the arc (HF start or Lift TIG).
- Maintain a consistent arc length and feed the filler rod into the weld puddle as needed.
- Move the torch steadily along the joint.
- At the end of the weld, release the torch trigger. The post-flow gas will continue to shield the hot weld and tungsten.
- Power Off: After welding, turn off the gas cylinder, then turn off the welder using the power switch.
7. Maintenance
Regular maintenance ensures the longevity and optimal performance of your welding machine.
- Cleaning: Regularly clean the exterior of the machine with a dry, soft cloth. Periodically open the casing (only by qualified personnel) to remove dust and debris from internal components, especially the cooling fan and heat sinks, using compressed air.
- Cable Inspection: Inspect all welding cables, gas hoses, and power cords for cuts, abrasions, or damage before each use. Replace damaged cables immediately.
- Torch Maintenance:
- Inspect the TIG torch head, collet, collet body, and ceramic nozzle for wear or damage. Replace as necessary.
- Ensure the tungsten electrode is properly ground and free from contamination.
- Connection Checks: Ensure all electrical and gas connections are tight and secure.
- Storage: Store the welder in a clean, dry environment when not in use.
8. Troubleshooting
This section addresses common issues you might encounter. For problems not listed here, contact technical support.
| Problem | Possible Cause | Solution |
|---|---|---|
| No power when switched ON | Power cord unplugged, circuit breaker tripped, internal fuse blown. | Check power cord connection. Reset circuit breaker. Contact service for fuse replacement. |
| No arc or weak arc | Poor earth clamp connection, incorrect welding parameters, contaminated tungsten, gas flow issue. | Ensure earth clamp has good contact. Adjust current/voltage. Re-grind or replace tungsten. Check gas supply. |
| Porous weld / Poor shielding | Insufficient gas flow, gas leak, contaminated gas, draft in welding area, incorrect post-flow. | Increase gas flow. Check gas hose for leaks. Use pure gas. Shield welding area from drafts. Adjust post-flow time. |
| Overheating protection activated | Exceeded duty cycle, blocked ventilation, high ambient temperature. | Allow machine to cool down. Ensure ventilation is clear. Reduce welding time or current. |
9. Specifications
Technical specifications for the JASIC WSME-200 (E201II) TIG Welder.
| Feature | Specification |
|---|---|
| Product Name | WSME-200 |
| Function | Inverter IGBT Welding Machine |
| Rated Input Voltage | 220 V |
| Max. Load Power Capacity | 6KVA |
| Output Polarity | AC/DC TIG |
| Rated Duty Cycle @40°C (TIG) | 25% |
| Rated Output Current (TIG) | 200 A |
| Rated Output Voltage (TIG) | 22 V |
| Welding Current/Voltage Range | 10-200A |
| Pulse Frequency | 50/60Hz |
| Motor Type | DC MOTOR |
| Dimensions | 541*232*410mm |
| Weight (KG) | 12.9 KG |
| Material / Metal Processed | Carbon steel, Stainless steel, Aluminium alloy |
| Use / Application | Welding steel, iron, titanium, copper, nickel; Aluminum Tig Welding |
| Key Selling Points | Easy to Operate |
| Applicable Industries | Building Material Shops, Machinery Repair Shops, Manufacturing Plant |
| Machinery Test Report | Provided |
| Video Outgoing-inspection | Provided |
| Feature | INVERTER |
| Accessories | Earth Clamp+TIG Torch |
| Efficiency | 85% Inverter Welders |
10. Warranty and Support
The JASIC WSME-200 (E201II) TIG Welder comes with a 1-year warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use conditions.
For technical assistance, troubleshooting guidance, or warranty claims, please contact your authorized dealer or the manufacturer's support team. Video technical support is provided to assist with setup and operational queries.