JIKONG JK-PB2A16S30P V19

Contents

JIKONG JK-PB2A16S30P V19 Smart BMS User Manual

For Li-ion, LiFePO4, and LTO Battery Household Energy Inverter Systems

1. Product Overview

The JIKONG JK-PB2A16S30P V19 Smart Battery Management System (BMS) is designed for advanced battery protection and management in household energy inverter systems. It supports 8S-16S configurations for Li-ion, LiFePO4, and LTO battery types, offering a continuous charge/discharge current of 300A and an active balancing current of 2A. This smart BMS integrates intelligent communication, efficient balancing, and robust protection features to ensure the longevity and safety of your battery packs.

JIKONG JK-PB2A16S30P V19 Smart BMS with V19 Display
Figure 1: JIKONG JK-PB2A16S30P V19 Smart BMS with V19 Display.

The BMS is built with precision aesthetics and peak performance in mind, featuring carefully crafted components including a cooling aluminum alloy, high-performance MCU, flexible wiring terminals, parallel current limiting module, low internal resistance MOS, sampling line, interface board, and chip indicator light.

Internal components of the JIKONG Smart BMS
Figure 2: Internal components of the JIKONG Smart BMS, highlighting cooling aluminum alloy, MCU, and wiring terminals.

2. Packing List

Please verify that all items are present in the package before proceeding with installation.

JIKONG BMS Packing List
Figure 3: Visual representation of the JIKONG BMS packing list.
  • BMS x 1
  • Interface board x 1
  • Adapter cable B x 1 (long 30cm)
  • Adapter cable A x 1 (long 30cm)
  • R545 Network cable x 1 (long 40cm)
  • Cells total B+ Cable x 1 (long 50cm)
  • Sampling line A x 2 (long 90cm)
  • Sampling line B x 1 (long 90cm)
  • Sampling line C x 1 (long 90cm)
  • Switch x 1 (long 50cm)
  • Adapter cable C x 1 (long 30cm)
  • Heating Adapter cable x 1 (long 17cm)
  • Adapter x 1

3. Installation and Wiring

Careful installation and correct wiring are crucial for the safe and efficient operation of your BMS. Please follow these steps precisely.

3.1 General Installation Steps

  1. Connect all necessary cables to the BMS.
  2. Insert the main cable into the BMS unit.
  3. Connect the B-line (negative battery terminal) and the P-line (positive battery terminal) to the battery pack.
  4. Important Note: If there are two B8 cables, only the first B8 line needs to be connected. The second B8 cable should not be connected.

3.2 Wiring Diagrams

Refer to the following diagrams for specific wiring methods based on your battery string configuration.

Wiring diagrams for 16-string and 8-string battery cells
Figure 4: Wiring methods for 16-string and 8-string battery cells, including connections for B-, P-, B+, display/switch, heater element, and temperature control switch.

3.3 Interface Board Details

The BMS features a versatile interface board supporting multiple communication modes.

JIKONG BMS communication modes and interface board details
Figure 5: Diagram illustrating the four communication modes (CAN, RS485, UART, RS232) and a detailed view of the interface board with various ports and a dial switch.

The interface board includes:

  • RS485-1 and RS485-2 interfaces (BPBC RJ45 Socket)
  • RS232 interface
  • CAN interface
  • Dry Interface
  • Dial Switch for configuration

4. Operating Instructions

The JIKONG Smart BMS offers intelligent interaction and easy operation through mobile applications and PC software.

4.1 Mobile App Operation

The mobile phone Bluetooth APP, named "JIKONG BMS", allows you to monitor and configure your battery system. It supports iOS, Android, and HarmonyOS systems and can automatically switch languages with your mobile phone system.

Mobile app interface for JIKONG BMS protocol docking
Figure 6: Mobile app interface for protocol docking and configuration, showing options for selecting UART and CAN protocols.

Through the app, you can:

  • View real-time data such as voltage, current, temperature, State of Charge (SOC), and cycle count.
  • Adjust multiple protection values including overcharge, overdischarge, overcurrent, temperature, and balance settings.
  • Select and configure various inverter communication protocols.

4.2 PC Software Operation

The BMS can also be managed and configured using PC host computer software. This provides a comprehensive interface for detailed parameter adjustments and monitoring.

PC host computer software interface for JIKONG BMS
Figure 7: Screenshot of the PC host computer software interface for setting inverter communication protocols and adjusting parameters.

Supported CAN Protocols via PC software:

Protocol NameProtocol NameProtocol Name
JIKONGNIUChina tower
GrowattVoltroncWOW

4.3 Multi-screen Data Connection

You can freely choose between the mobile app, computer upper computer software, or a dedicated JIKONG home storage display to monitor your battery system data.

Multi-screen display options for JIKONG BMS data
Figure 8: Multi-screen display options for BMS data, including mobile app, PC software, and JIKONG home storage dedicated display.
JIKONG home storage dedicated display
Figure 9: JIKONG home storage dedicated display showing voltage, current, temperature, and number of strings.

5. Specifications

The JIKONG JK-PB2A16S30P V19 Smart BMS is engineered for high performance and reliability.

5.1 Key Features

JIKONG JK-PB2A16S30P V19 Smart BMS features
Figure 10: Overview of the JK-PB2A16S30P V19 Smart BMS features.
  • Model: JK-PB2A16S30P V19
  • Functions: Bluetooth (BT), RS232, RS485, CAN, Heating (HEAT), UART
  • BMS Type: Inverter BMS
  • Balancing Current: 2A
  • Battery Strings: 8S-16S
  • Charge/Discharge Current: 300A
  • Battery Type Compatibility: Li-ion, LiFePO4, LTO

5.2 Technical Parameters

JIKONG Product Specifications Table
Figure 11: Detailed table of JIKONG Product Specifications.
Technical IndexJK-PB2A16S30P
Number of Battery Strings (Li-ion)7S-16S
Number of Battery Strings (LiFePO4)8S-16S
Number of Battery Strings (LTO)14S-16S
Balance MethodActive Balance (Full State On)
Balance Current2A
Conductive Resistance in Main Circuit0.25mΩ
Continuous Discharge Current300A
Maximum Discharge Current (MAX 2min)300A
Over Charge Protection Current (ADJ)600A
Other Interfaces (Default)RS485/232/CAN/UART
Supply Voltage20-70V
Wiring OutputCommon Port
Single Cell Voltage Range1-5V
Voltage Acquisition Accuracy±5mV
Over Charge Protection Voltage1.2-4.35V Adjustable
Over Charge Release Voltage1.2-4.35V Adjustable
Over Current Detect Delay2-120S Adjustable
Over Discharge Protection Voltage1.2-4.35V Adjustable
Over Discharge Release Voltage1.2-4.35V Adjustable
Quantity of Temperature Detection4
Temp ProtectionYes
Short Circuit ProtectionYes
Coulomb CounterYes
Bluetooth FunctionSupport for Android/iOS/Harmony
Parallel charging current limiting10A
Address dial switch4
DRY Contact2

5.3 Advanced Technologies

  • Patented Parallel Protection Technology: Features an integrated 10A current limiting module, enabling safe expansion of battery capacity through parallel connection of multiple battery packs.
  • Patented parallel protection technology for battery expansion
    Figure 12: Illustration of the patented parallel protection technology with an integrated 10A current limiting module.
  • Efficient Balance: The equilibrium efficiency is increased by up to 400%, significantly improving the issue of batteries not being fully charged or discharged. The JIKONG BMS achieves a balanced current of 1A-2A, compared to 30-100mA in ordinary protection boards.
  • Comparison of balancing efficiency between JIKONG BMS and ordinary protection boards
    Figure 13: Comparison illustrating the efficient balance feature of JIKONG BMS.
  • Aluminum Alloy Heat Sink: Designed with an aluminum alloy heat sink to effectively reduce the temperature rise of the protection board, enhancing reliability.
  • Aluminum alloy heat sink on JIKONG BMS
    Figure 14: Close-up view of the aluminum alloy heat sink on the JIKONG BMS.

5.4 Application Scenarios

The JIKONG Home Energy Storage BMS is tailor-made for home energy storage systems and is also suitable for various other applications:

  • Communication base stations
  • Building energy storage
  • Industrial energy storage
  • Farm energy systems
  • Office energy solutions
Application scenarios for JIKONG Home Energy Storage BMS
Figure 15: Various application scenarios for the JIKONG Home Energy Storage BMS.

6. Maintenance

To ensure optimal performance and longevity of your JIKONG Smart BMS, consider the following maintenance guidelines:

  • Regularly check all wiring connections for tightness and corrosion.
  • Keep the BMS unit clean and free from dust and debris to ensure proper heat dissipation.
  • Monitor battery cell voltages and temperatures through the mobile app or PC software to identify any anomalies early.
  • Ensure the BMS is installed in a well-ventilated area, away from direct sunlight or excessive heat sources.
  • Periodically update the BMS firmware if new versions are released by JIKONG to benefit from improvements and bug fixes.

7. Troubleshooting

If you encounter issues with your JIKONG Smart BMS, refer to the following general troubleshooting steps:

  • No Power/No Display: Check all power connections, including the main battery connections (B- and P-lines) and the supply voltage. Ensure the switch is in the 'on' position.
  • Communication Issues (Bluetooth/RS485/CAN): Verify that the communication cables are correctly connected. For Bluetooth, ensure the app is installed correctly and permissions are granted. For wired communication, check the protocol settings in the app or PC software.
  • Overcharge/Overdischarge Protection Triggered: Review your battery cell voltage settings in the app/PC software. Ensure they are appropriate for your battery chemistry and configuration. Check individual cell voltages for imbalance.
  • Overcurrent/Short Circuit Protection Triggered: Disconnect the load and inspect for any short circuits in the system. Gradually re-apply load to identify the source of the overcurrent.
  • Temperature Alarms: Ensure the BMS is adequately cooled and not exposed to high ambient temperatures. Check for any obstructions to airflow around the heat sink.
  • Battery Imbalance: The active balancing feature should manage this. If persistent imbalance occurs, check individual cell connections and consider a full balance cycle through the BMS settings.

For complex issues, consult the official JIKONG support resources or a qualified technician.

8. User Tips

  • Always double-check wiring before applying power to prevent damage to the BMS or battery pack.
  • Familiarize yourself with the mobile app and PC software settings to fully utilize the smart features and customize protection parameters.
  • For optimal battery life, try to keep your battery within recommended voltage and temperature ranges, avoiding frequent deep discharges or prolonged full charges.
  • Consider using compatible JIKONG BMS accessories, such as external displays, for enhanced monitoring and control.
  • JIKONG BMS accessories
    Figure 16: Various JIKONG BMS accessories available for enhanced functionality.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official JIKONG website or contact your authorized dealer. Ensure you have your product model number (JK-PB2A16S30P V19) and purchase details available when seeking support.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.