Introduction
This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your Estardyn 1.54 inch TFT LCD Display Module with EC11 Rotary Encoder Button. This module is designed for DIY electronics projects, offering a compact display and versatile input control for platforms like Arduino, ESP32, and ESP8266.
Product Overview

The module integrates a 1.54-inch TFT LCD display with a 240x240 resolution and an EC11 rotary encoder with an integrated push button. It supports both IIC/I2C and SPI communication interfaces, making it highly adaptable for various microcontroller projects.
Setup Instructions
Before connecting the module, ensure your microcontroller (e.g., Arduino, ESP32, ESP8266) is powered off.
Pinout Diagram and Description

Refer to the following table for the pin descriptions:
| Pin Label | Description |
|---|---|
| GND | Ground connection. |
| VCC | Power supply (typically 3.3V or 5V, check your microcontroller's logic level). |
| SCL | Serial Clock (for I2C/SPI communication). |
| SDA | Serial Data (for I2C/SPI communication). |
| RES | Reset pin for the LCD. |
| DC | Data/Command selection pin for the LCD. |
| CS | Chip Select pin for the LCD. |
| BLK | Backlight control pin (optional, can be connected to VCC for always on). |
| TRA | Rotary Encoder Channel A. |
| TRB | Rotary Encoder Channel B. |
| PSH | Rotary Encoder Push Button. |
| KO | (Likely another encoder pin or unused, verify with specific library/datasheet). |
Connection Guidelines
- Power Supply: Connect GND to your microcontroller's ground and VCC to its 3.3V or 5V power output. Ensure voltage compatibility.
- Communication Interface:
- SPI Mode: Connect SCL, SDA, RES, DC, CS to appropriate digital pins on your microcontroller. SCL acts as SCK, SDA as MOSI. MISO is typically not used for display-only modules.
- I2C Mode: Connect SCL and SDA to your microcontroller's I2C pins (e.g., A4/A5 on Arduino Uno, GPIO21/GPIO22 on ESP32). RES, DC, CS might be tied to specific logic levels or not used, depending on the display's internal configuration and driver.
- Rotary Encoder: Connect TRA, TRB, and PSH to digital input pins on your microcontroller. It is recommended to use internal pull-up resistors or external pull-up resistors for these pins.
- Backlight: Connect BLK to VCC for constant backlight, or to a PWM-capable pin for brightness control.
Note: Specific pin assignments and library usage will depend on your chosen microcontroller and development environment. Consult the documentation for your microcontroller and display library (e.g., Adafruit GFX, TFT_eSPI) for detailed programming instructions.
Operating Instructions
Display Operation
The 1.54 inch TFT LCD is a color display. Once correctly initialized with a compatible library, you can draw text, graphics, and images. Common functions include:
tft.init(): Initializes the display.tft.setRotation(rotation): Sets the display orientation.tft.fillScreen(color): Fills the entire screen with a specified color.tft.drawString(text, x, y): Draws text at a given coordinate.tft.drawPixel(x, y, color): Draws a single pixel.tft.drawRect(x, y, w, h, color): Draws a rectangle.
Rotary Encoder Operation
The EC11 rotary encoder provides two primary input methods:
- Rotation: Turning the knob clockwise or counter-clockwise generates pulses on the TRA and TRB pins. By monitoring the sequence of these pulses, your microcontroller can detect the direction and amount of rotation. This is commonly used for menu navigation or value adjustment.
- Button Press: Pressing the knob activates the PSH pin. This acts as a momentary switch, useful for selection or confirmation.
Libraries are available (e.g., "RotaryEncoder" for Arduino) to simplify reading the encoder's state.
Maintenance
- Cleaning: Gently wipe the display surface with a soft, lint-free cloth. For stubborn smudges, use a small amount of isopropyl alcohol on the cloth, not directly on the screen.
- Storage: Store the module in a dry, anti-static environment, away from direct sunlight and extreme temperatures.
- Handling: Avoid applying excessive force to the display or the rotary encoder. Static electricity can damage electronic components; handle with care, preferably using anti-static precautions.
Troubleshooting
- Display Not Lighting Up:
- Check VCC and GND connections for proper voltage and polarity.
- Ensure the BLK pin is connected to VCC or a correctly configured PWM pin.
- Verify that the display initialization code in your program is correct and running.
- No Image or Garbled Display:
- Double-check all SPI/I2C communication pin connections (SCL, SDA, RES, DC, CS).
- Confirm that the correct display driver library is installed and configured for the module's specific driver chip (e.g., ST7789, ILI9341). While the exact chip isn't specified, common libraries often support multiple.
- Ensure the communication protocol (SPI or I2C) is correctly selected in your code and matches your wiring.
- Rotary Encoder Not Responding:
- Verify TRA, TRB, and PSH pin connections to your microcontroller.
- Ensure internal or external pull-up resistors are enabled/connected for the encoder pins.
- Check your code for correct reading of encoder states and button presses.
Specifications
| Feature | Detail |
|---|---|
| Brand Name | Estardyn |
| Model Number | 1.54 TFT |
| Display Type | TFT LCD |
| Display Size | 1.54 inch |
| Resolution | 240x240 pixels |
| Display Mode | 240*240 (pixel matrix) |
| Interface | IIC/I2C, SPI |
| Input Device | EC11 Rotary Encoder with Push Button |
| Origin | Mainland China |
| Package Length | 10 cm |
| Package Width | 8 cm |
| Package Height | 3 cm |
| Package Weight | 0.035 kg |
User Tips
- Driver Chip: While the specific driver chip (e.g., ST7789, ILI9341) is not explicitly stated, most 1.54-inch 240x240 TFT displays commonly use the ST7789V driver. When selecting a library for your microcontroller, try libraries compatible with ST7789V if you encounter display issues.
- Logic Level: Always verify the operating voltage of your microcontroller and the display module. If your microcontroller operates at 5V and the display at 3.3V, use a logic level shifter to prevent damage.
- Libraries: Utilize existing open-source libraries for TFT displays (like Adafruit GFX, TFT_eSPI) and rotary encoders. These libraries significantly simplify the coding process.
Warranty and Support
For technical support, driver information, or specific programming examples, please refer to the seller's product page or contact Estardyn customer service. Keep your purchase records for any warranty claims.