TUYA YNG206

Contents

Universal RX MULTI Tuya WiFi Smart Switch Module User Manual

Model: YNG206

1. Introduction

The Universal RX MULTI Tuya WiFi Smart Switch Module (Model: YNG206) is a versatile 2-channel receiver designed to integrate your garage door or gate opener with smart home systems. It supports a wide range of RF frequencies (300-868MHz) and various encoding formats, allowing control via both traditional RF remote controls and a mobile application (Tuya Smart or Smart Life). This module offers enhanced convenience through WiFi connectivity, voice control compatibility with Alexa and Google Assistant, and advanced scheduling features.

Universal RX MULTI Tuya WiFi+RF Smart Switch Modules
Figure 1: Universal RX MULTI Tuya WiFi+RF Smart Switch Modules (AC/DC 9-30V and AC 85-250V versions)
Comparison of WiFi+RF and RF-only versions of the smart switch module
Figure 2: Comparison of WiFi+RF and RF-only versions

2. Specifications

AttributeValue
Model NumberYNG206
Product NameTUYA RX-MULTI WIFI Receiver
Operating VoltageAC/DC 9V-30V or AC 85-250V
Channels2
RF Frequency300MHz - 868MHz (AM/FM280-915MHz)
Wireless StandardWi-Fi 2.4GHz b/g/n + Bluetooth
Code SupportFixed Code, Learning Code, Rolling Code (e.g., 2262, 1527, HCS301)
Maximum Power660W / 3A
Control MethodJog (Momentary)
Wireless Remote Control Distance> 50m
Product Size57mm * 47mm * 25mm
Working Temperature-40℃ ± 80℃
CertificationsCE, FCC, RoHS, WEEE
Max Remote Controls Supported400

Power Input Selector: This receiver can operate at AC/DC 9V~30V or AC 85-250V. It is important to adjust the Power Input Selector (PIS) according to your power input. If the input voltage is greater than 24V, shorten pins 2&3. If the input voltage is less than 24V, shorten pins 1&2.

3. Package Contents

Ensure all items are present in the package:

  • 1 x TUYA RX-MULTI WIFI Receiver Module
  • 1 x Small Antenna
  • 1 x English User Manual

4. Pre-Use Checklist

Before proceeding with installation and setup, please verify the following:

  • Your phone or tablet is connected to a 2.4GHz WiFi network. 5GHz WiFi networks are not supported.
  • Bluetooth is enabled on your phone.
  • For Android devices, ensure the system version is at least 4.0.
  • For Apple devices, ensure you have access to the App Store.
  • If your wireless router has MAC address filtering enabled, ensure it is temporarily disabled during setup or configured to allow the device.

5. Device Installation

5.1. Wiring Instructions

WARNING: Ensure the device is in a power-off state before starting any wiring. Live installation is strictly prohibited and can cause electric shock or damage to the device.

  1. Connect the device power supply according to the chosen voltage version (AC/DC 9-30V or AC 85-250V).
  2. Follow the wiring diagrams below for correct connections. The outputs (OUT1, OUT2) are relay contacts (Normally Open - NO) and can switch up to 3A at the input voltage (max 660W).
Wiring diagram for AC/DC 9-30V smart switch module
Figure 3: Wiring Diagram for AC/DC 9-30V Version
Wiring diagram for AC 85-250V smart switch module
Figure 4: Wiring Diagram for AC 85-250V Version

5.2. Initial Power On and Reset

  1. After completing the wiring, turn on the power. The device will default to 'off' for incoming calls (this setting can be changed in the app).
  2. If the network indicator light on the device flashes twice per second, the device is ready for network configuration. If not, you may need to reset it.
  3. To Reset the Device: Press and hold the reset button (located on the module) for approximately 6 seconds until the network indicator light flashes rapidly (2 flashes per second). This indicates the device has entered network redistribution mode.

6. Mobile App Setup

6.1. App Download

Download the

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.