BAOFENG AR-39

Contents

BAOFENG AR-39 Multi-Band Walkie Talkie User Manual

Model: AR-39

1. Introduction

Thank you for choosing the BAOFENG AR-39 Multi-Band Amateur Radio. This device utilizes advanced technology to provide reliable communications in demanding environments. It features emergency alarm, NOAA weather radio, airband receiver, DTMF, 2TONE, 5TONE, CTCSS/DCS encode/decode, and a bright flashlight. This manual provides detailed instructions for safe and effective use.

Important Safety Information:

  • FCC Regulatory Conformance: This equipment complies with Part 15 of FCC Rules. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
  • RF Exposure Compliance: To control exposure and ensure compliance with occupational/controlled environmental RF exposure limits, always adhere to the following procedures:
    • Do not remove the RF Exposure Label.
    • Transmit no more than 50% of the time. Press the Push-to-Talk (PTT) key to transmit; release to receive.
    • Keep the radio unit at least 2.5cm away from the face during operation.
    • When worn on the body, always place the radio in an approved holder, holster, case, or body harness.
    • Use only approved antennas, batteries, and accessories.
  • Operating Prohibitions: Do not operate in locations with fuels, chemicals, explosive atmospheres, or near blasting areas. Avoid use near medical or electronic equipment vulnerable to RF signals. Do not operate while driving.

2. Radio Overview

Labeled diagram of the BAOFENG AR-39 Walkie Talkie showing its components and dimensions.
Figure 1: BAOFENG AR-39 Component Diagram. Dimensions: 13.8cm/5.4in (height), 3.3cm/1.3in (depth), 5.5cm/2.2in (width).

The BAOFENG AR-39 features a 2.0" TFT large screen and a full keyboard for intuitive operation. Key components include:

  • Antenna: For signal transmission and reception.
  • PTT Key: Push-to-Talk button for transmitting.
  • Accessory Jack: For connecting external speaker/microphone.
  • Color LCD: 2.0" TFT display with 7 color font options.
  • MENU Key: Accesses the radio's main menu.
  • P1-VFO/MR Mode Key: Switches between Frequency (VFO) and Memory (MR) modes.
  • Numeric Keypad: For direct frequency input and menu navigation.
  • Channel Knob: For channel selection.
  • Power/Volume Knob: Turns the radio on/off and adjusts volume.
  • RX_TX Status LED: Indicates receiving (green) or transmitting (red) status.
  • SK1/SK2 Programmable Keys: User-assignable shortcut keys (e.g., FM Radio, Monitor, Flashlight).
  • EXIT Key: Returns to previous menu or screen.
  • Navigation Keys (▲/▼): For menu navigation and frequency adjustment.
  • Speaker: For audio output.
  • Battery Release Latch: Releases the battery pack.
  • LED Flashlight: Upgraded spotlight flashlight for enhanced illumination.
  • Flashlight Key: Activates the flashlight.

3. Setup

3.1. Content of the Packaging

Your BAOFENG AR-39 package should include the following items:

  • 1X Portable radio body
  • 1X Antenna
  • 1X Li-ion battery pack
  • 1X Belt Clip
  • 1X Charger (with Type-C cable)
  • 1X Wrist Belt
  • 1X User's manual
Image showing the contents of the BAOFENG AR-39 package: radio, antenna, battery, Type-C cable, base charger, and manual.
Figure 2: Package Contents

3.2. Charging the Battery Pack

The Li-ion battery pack is not fully charged at the factory. For optimal performance, fully charge and discharge the battery two or three times before regular use.

Precautions for Batteries:

  • Do not charge or replace your battery in locations with fuels, chemicals, or explosive materials.
  • Dry a wet battery with a soft, clean cloth before charging.
  • Do not charge a deformed, leaking, or overheated battery.
  • Use only the authorized charger supplied by BAOFENG.
  • Do not charge the battery in areas with strong radiation.
  • Avoid overcharging, as it may shorten battery life.
  • Charge the battery between 5℃ and 40℃ (40°F - 105°F).
  • Turn off the radio before inserting it into the charger for a full charge.
  • Do not remove the battery or unplug the power cord during charging.
  • Do not dispose of the battery in fire or expose it to direct sunlight/heat.
  • Do not squeeze or penetrate the battery.
  • When storing, keep the battery at 80% discharge in a low-temperature, dry environment.

How to Charge:

  1. Plug the AC adaptor into an AC outlet, then connect the cable to the DC jack on the back of the charger. The indicator light will blink orange, indicating it's ready.
  2. Plug the battery or the radio into the charger. Ensure good contact between terminals. The indicator light will turn red, indicating charging has begun.
  3. A full charge takes approximately 2-5 hours. The lamp turns green when charging is complete.

LED Indicator Status:

StatusLED Indication
No BatteryGreen and red alternately flashing
Charge NormallyRed
Fully ChargedGreen
Trouble (battery too warm, short-circuited, or charger short-circuited)Red blinks fast for a long time

Using the Type-C USB Charger:

Image showing multiple charging methods for the BAOFENG AR-39, including Type-C direct charging, desktop charger, and battery charging.
Figure 3: Multiple Charging Methods

The Type-C USB port allows for convenient charging from various sources like a car charger, power bank, or laptop.

  1. Ensure your radio is turned OFF.
  2. Plug the Type-C USB cable into the battery's charging port and connect the other end to a wall outlet or compatible USB power source.
  3. An empty battery will fully charge in approximately 4 hours.
  4. The battery meter on the LCD will indicate charging status.

Note: It is recommended to power OFF your radio while charging. If powered on, you may not be able to transmit until the battery has charged to at least one bar. For optimal battery life, remove the radio from the charger within 6 hours after full charge.

3.3. Installation of Accessories

Before attaching or removing the battery, ensure the radio is turned off by rotating the power/volume knob counter-clockwise.

Installing/Removing the Antenna:

  1. Installing: Screw the antenna into the connector on top of the transceiver clockwise until secure.
  2. Removing: Turn the antenna counter-clockwise to remove it.

Installing the Battery Pack:

  1. Align the battery in parallel with the radio body, with the lower edge 1-2cm below the radio's edge.
  2. Slide the battery upward along the guide-rails until it clicks into place.

Removing the Battery Pack:

Press the battery release latch above the battery pack and slide the battery downward.

Installing the Additional Speaker/Microphone (Optional):

Wiring diagram for connecting an external speaker/microphone to the radio's accessory jack.
Figure 4: Speaker/Microphone Accessory Jack Wiring

Pry open the rubber MIC-Headset jack cover and insert the Speaker/Microphone plug into the double jack.

4. Operating Instructions

4.1. Basic Operations

Power On/Off:

  • To Turn On: Rotate the Volume/Power knob clockwise until you hear a "click". The display will show a message or flash, and a voice prompt may announce "frequency mode" or "channel mode".
  • To Turn Off: Rotate the Volume/Power knob counter-clockwise until you hear a "click".

Adjusting the Volume:

  • Rotate the Volume/Power knob clockwise to increase volume.
  • Rotate the Volume/Power knob counter-clockwise to decrease volume.

Main Band/Sub Band Switch:

  • Press the P2 key to switch between the A (upper) and B (lower) displays. The selected display's frequency or channel becomes active for listening and transmitting.

VFO/Channel Switch:

  • Press the P1 key to switch between Frequency (VFO) Mode and Memory (MR) Mode (also known as Channel Mode).

Frequency (VFO) Mode:

In VFO mode, you can navigate frequencies using the ▲/▼ keys or input them directly via the numeric keypad. For example, to enter 436.61250 MHz on display A:

  1. In standby mode, press P1 to switch to VFO mode.
  2. Enter [4][3][6][6][1][2][5][0] on the numeric keypad.

Warning: Transmitting on unauthorized frequencies is illegal. Always ensure you are licensed for the frequencies you operate on.

Channel (MR) Mode and Channel Selection:

In MR mode, you can select channels using the ▲/▼ navigation keys, the channel switch, or by inputting channel numbers directly via the keypad.

Select a Zone:

The radio supports up to 10 zones, each with up to 64 channels. To select a zone, go to Menu > Zone, then use the ▲/▼ keys to select and confirm.

Making a Call:

  • Channel Mode Call: Select a channel, then hold down the PTT key to transmit. Speak into the microphone with a normal tone. The red LED will illuminate.
  • Frequency Mode Call: Press P1 to switch to frequency mode, input the desired frequency, then hold down the PTT key to transmit.
  • Receive a Call: Release the PTT key. The green LED will illuminate when receiving a call.

Note: For best reception, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.

Emergency Alert:

Press the pre-programmed [SOS] key to activate the emergency alert function. Press it again to exit. Use only in actual emergencies.

FM Radio (FM):

Access FM Radio via Menu -> Radio Settings -> FM Radio. You can search for stations using the # key for automatic scan, ▲/▼ keys for channel selection, or direct numeric input for frequencies.

Radio Interrupt:

When FM radio is active, you can configure whether the radio can still receive or transmit on the channel (On) or if transmission/reception is blocked (Off).

Monitor:

Press the pre-programmed [Monitor] key to monitor weak signals or matched carriers. Press again to exit.

Keypad Lock:

Press and hold the * key for about two seconds to enable or disable the keypad lock. The radio can also be set to automatically lock after ten seconds via the menu.

Frequency Reversal:

A short momentary press of the * key enables the reverse function, swapping transmit and receive frequencies.

TX Repeaters Tone:

The radio supports 1750Hz, 1000Hz, 1450Hz, and 2100Hz tone bursts for repeater activation. Use the pre-programmed [1750Hz] key to send tone bursts.

NOAA Weather/Weather Alert:

The radio can receive weather reports from designated NOAA stations. Press and hold the 0 key to enter NOAA scan reception mode. Use ▲/▼ keys or the # key to cycle through channels. The following table lists NOAA weather channel frequencies:

Channel NumberRX Frequency MHzChannel NumberRX Frequency MHz
CH-01162.550CH-06162.500
CH-02162.400CH-07162.525
CH-03162.475CH-08161.650
CH-04162.425CH-09161.775
CH-05162.450CH-10163.275

Note: These are receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.

One Touch Frequency Search:

Access via Menu -> Radio Settings -> OneTouch Search. Press the pre-programmed [OneTouch Search] key to start. The screen will display "Seeking" and the indicator light will be yellow. Upon success, the search frequency and CTCSS/DCS will be displayed, and the speaker will activate. You can save the frequency to a channel or press the PTT key for a callback.

4.2. Advanced Features

Scanner:

The radio features a built-in scanner for VHF and UHF bands. In VFO mode, it scans according to your set frequency step. In MR mode, it scans your channels. To enable, press and hold the # key for about two seconds. You can change the scanning direction with the ▲/▼ keys.

  • Frequency Ranger: Set start and end values for frequency sweep in VFO mode.
  • Channel Scan Range: Scan all channels in the current zone or only added channels.
  • Scan Modes: Time Operation (TO), Carrier Operation (CO), Search Operation (SE).
  • Scan Sub-Code (CTCSS/DCS): Search for CTCSS/DCS codes.

DTMF (Dual-Tone Multi-Frequency):

DTMF is an in-band signaling method. The radio supports full DTMF implementation, including A, B, C, and D codes. Numeric keys and *, #, ▲, ▼, ◄, ► keys correspond to DTMF codes. To send, press the desired key(s) while holding down the PTT key.

1209Hz1336Hz1477Hz1633Hz
697Hz123A
770Hz456B
852Hz789C
941Hz*0#D

Dual Watch:

Allows monitoring of two channels simultaneously. Enable/disable via Menu. Options include "Double Wait" (monitors both, 'DW' icon displayed) and "Signal Wait" (monitors both, transmits/receives on main channel only).

Manual Programming (Channels Memory):

Store frequently used frequencies for easy retrieval. The manual provides examples for programming a Channel Repeater Offset with CTCSS Tone and a Simplex Channel with CTCSS Tone.

Repeaters Programming:

Instructions are provided for setting up the transceiver to work with repeaters, including entering repeater output frequency, offset frequency, and offset direction. It also covers setting up CTCSS tones for repeaters.

5. Maintenance

5.1. General Care

  • Do not use any unauthorized or damaged accessories.
  • Keep the product at least 2.5 centimeters away from your body during transmission.
  • Avoid prolonged use at high volume.
  • Do not place the product in the area over an airbag or in the airbag deployment area in vehicles.
  • Keep the product and its accessories out of reach of children and pets.
  • Operate the product within the specified temperature range.
  • Allow the product to cool down after continuous transmission.
  • Handle the product with care; do not disassemble, modify, or repair it without authorization.

5.2. Battery Maintenance

  • Regularly clean the charging connector with a clean, dry cloth to prevent charging issues.
  • Charge the battery within the recommended temperature range of 5℃ to 40℃.
  • Turn off the radio during charging to ensure a full charge.
  • Do not remove the battery or unplug the power cord during charging.
  • Do not dispose of the battery in fire.
  • Avoid exposing the battery to direct sunlight or other heat sources.
  • Do not squeeze or penetrate the battery, or remove its housing.

6. Troubleshooting Guide

If you encounter any issues with your BAOFENG AR-39, refer to the table below for common problems and their solutions. If problems persist, contact your dealer for technical support.

PhenomenaAnalysisSolution
You cannot turn on the radio.The battery may be installed improperly.
The battery power may run out.
The battery may suffer from poor contact caused by dirty or damaged battery contacts.
Remove and reattach the battery.
Recharge or replace the battery.
Clean the battery contacts or replace the battery.
During receiving, the voice is weak or intermittent.The battery voltage may be low.
The volume level may be low.
The antenna may be loose or improperly installed.
The speaker may be blocked.
Recharge or replace the battery.
Increase the volume.
Turn off the radio, then remove and reattach the antenna.
Clean the surface of the speaker.
You cannot communicate with other group members.The frequency or signaling type may be inconsistent with that of other members.
You may be too far away from other members.
Verify that your TX/RX frequency and signaling type are correct.
Move towards other members.
You hear unknown voices or noise.You may be interrupted by radios using the same frequency.
The radio in analog mode may be set with no signaling.
Change the frequency, or adjust the squelch level.
Request your dealer to set signaling for the current channel to avoid interference.
You are unable to hear anyone because of too much noise and hiss.You may be too far away from other members.
You may be in an unfavorable position (e.g., blocked by high buildings or underground areas).
It may be the result of external disturbance (e.g., electromagnetic interference).
Move towards other members.
Move to an open and flat area, restart the radio, and try again.
Stay away from equipment that may cause interference.
The radio keeps transmitting.VOX may be turned on or the headset is not installed in place.Turn off the VOX function. Check that the headphones are in place.

7. Technical Specifications

The following specifications are subject to change without prior notice or liability.

CategorySpecification
General
Channel Capacity640
Channel Spacing25.0 KHz/12.5 KHz
Input Voltage7.4 VDC
Battery Life (5% TX, 5% RX, 90% Standby)Li-on: 20 hours @ 5 watts
Operating Temperature-10°C to 50°C
Antenna Impedance50Ω
Radio Dimensions155mm X 64mm X 40mm (not including antenna)
Radio Weight354 g (with Li-ON battery)
Transmitter
Frequency Range (TX)144 to 148 MHz, 420 to 450 MHz (America version)
Modulation16K0F3E/11K0F3E
Spurious Emission-16 dBm<1GHz, -16 dBm>1GHz
Frequency Stability±2.5 ppm
Audio Distortion≤5%
FM Hum & Noise40 dB
Receiver
Frequency Range108-136, 136-174, 220-260, 350-390, 400 to 520 MHz (Scan Receiver)
Sensitivity (12 dB SINAD)-121 dBm
Adjacent Channel Selectivity-60 dBm
Intermodulation and Rejection-70 dBm
Rated Audio Power Output0.75 Watts @ 16 Ω
Rated Audio Distortion≤5%

Warning: The hardware is designed to support additional frequency bands. Ensure compliance with local radio regulations and consult your local radio administration for more compliance information.

8. User Tips

  • The BAOFENG AR-39 offers a great look and feel, making it a pleasant device to handle.
  • For programming, consider using the 5RH Pro software.
  • Note that AM frequencies may not be storable in memory channels on this model, which differs from some other Baofeng walkie-talkies.

9. Frequently Asked Questions (FAQ)

Q: Can I program this radio via Bluetooth?
A: The provided information suggests that some users desire Bluetooth programming, but it is not explicitly listed as a feature. Programming is typically done via PC software and a programming cable.
Q: Can I store AM frequencies in memory channels?
A: Based on user feedback, storing AM frequencies in memory channels might not be supported on this model, unlike some other Baofeng devices.
Q: What software can I use for programming?
A: Users have mentioned using "5RH Pro software" for programming this radio.

10. Warranty and Support

For any support inquiries or warranty information, please contact:

PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY LIMITED
ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong
Website: www.baofengradio.com or www.pofungshop.com

For detailed information, please refer to the full User's Manual PDF: BAOFENG AR-39UV SERIES User's Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.