Estardyn QC-MINI

Contents

USB Quick Charger Module (QC-MINI) User Manual

Model: QC-MINI | Brand: Estardyn

1. Product Overview

The Estardyn QC-MINI is a compact USB Quick Charger Module designed to provide fast charging capabilities for various devices. It functions as a step-down board, converting a wide input voltage range (6-32V) to automatically adjusted output voltages (5V/9V/12V) suitable for Quick Charge 2.0 and 3.0 compatible devices, as well as other fast charging protocols.

Front and back view of the QC-MINI USB Quick Charger Module
Figure 1: Front and back view of the QC-MINI USB Quick Charger Module, showing the USB-A output ports, inductor, capacitors, and input/output solder pads.
Top view of the QC-MINI module showing components and USB ports
Figure 2: Top view of the QC-MINI module, highlighting the dual USB-A output ports, the large inductor, two electrolytic capacitors, and the IP6505 chip.

2. Specifications

Key technical specifications for the QC-MINI module are provided below:

Attribute Value
Product Name QC-MINI QC2.0 QC3.0 Fast Charging Step Down Module
Product Number QC-MINI
Working Voltage DC 6.0-32V
Output Voltage DC 5V (Automatic adjust at 3.0V-12V in fast charging mode)
Output Power 24W
Conversion Efficiency About 95%
Working Current 30mA
Operating Temperature -40℃ ~ +85℃
Working Humidity Range 0%-95%RH
Size 38mm * 20mm * 10mm
Application Computer, Car Charger, Phone Fast Charging
Type Voltage Regulator (DIP Package)
Table of specifications and module dimensions
Figure 3: Detailed product specifications and a diagram showing the module's dimensions.

3. Setup Instructions

Follow these steps to correctly set up your QC-MINI module:

  1. Connect Input Terminal: Connect the power supply to the IN+ and IN- solder pads on the module. Ensure correct polarity: IN+ for positive, IN- for negative. The input voltage must be within the DC 6.0-32V range.
  2. Connect USB Device: Plug your USB charging cable into one of the USB-A output ports on the module. Connect the other end of the cable to your phone or other compatible device.

Important Note on Polarity: Input must not be reversed. Otherwise, the module will be permanently damaged.

Back view of the module showing input and output solder pads
Figure 4: Back view of the QC-MINI module, clearly labeled with "IN+", "IN-", "OUT+", "OUT-" for wiring connections.

4. Operating Instructions

The QC-MINI module automatically adjusts its output voltage to provide optimal fast charging for compatible devices.

4.1 Fast Charge Protocol Support

The module supports a variety of fast charging protocols, ensuring broad compatibility:

  • BC1.2 Protocol
  • Apple Protocol
  • Samsung Protocol
  • Qualcomm QC2.0 and QC3.0
  • Huawei FCP/SCP
  • Spreadtrum Fast Charge Protocol (SFCP)
  • Adaptive Fast Charging (AFC)

4.2 Automatic Voltage Adjustment

When a fast-charge compatible device is connected, the module communicates with the device to automatically adjust the output voltage between 3.0V and 12V to achieve the fastest possible charging speed. For non-fast charge devices, it defaults to 5V output.

Infographic detailing features, protocols, and usage notes
Figure 5: Infographic detailing product features, supported fast charging protocols, and usage steps.

5. Maintenance and Safety

To ensure longevity and safe operation of your QC-MINI module, observe the following:

5.1 Safety Features

The module incorporates several protection mechanisms:

  • Output Over-Voltage Protection: Prevents damage to connected devices from excessive voltage.
  • Output Over-Current Protection: Safeguards against excessive current draw.
  • Output Short-Circuit Protection: Protects the module and connected devices in case of a short circuit.
  • Input Over-Voltage Protection: Protects the module from high input voltages.
  • Input Under-Voltage Protection: Prevents operation with insufficient input voltage.
  • Module Over-Temperature Protection: Shuts down the module if it overheats.

5.2 General Care

  • Keep the module within the specified operating temperature range (-40℃ to +85℃) and humidity range (0%-95%RH).
  • Avoid exposing the module to moisture or extreme environmental conditions.
  • Ensure proper ventilation if integrating into an enclosure.
Infographic highlighting safety features and supported protocols
Figure 6: Infographic highlighting the module's safety features and supported fast charging protocols.

6. Troubleshooting

  • Device not fast charging:
    • Ensure your device supports one of the fast charging protocols listed (QC2.0, QC3.0, FCP, AFC, BC1.2, etc.).
    • Check the quality of your USB cable. Poor quality or excessively long cables can limit charging speed.
    • Verify that your input power supply can provide sufficient current and voltage for fast charging (e.g., a 12V input is needed for 9V/12V output).
  • No output voltage or module not working:
    • Double-check the input voltage. It must be within 6-32V.
    • Confirm input polarity (IN+ to positive, IN- to negative). Reverse polarity will damage the module.
    • Ensure the input power supply has enough capacity. If the input power is too small, the output voltage may drop to 5V or lower.
    • Check for any short circuits on the output.
  • Module overheating:
    • Ensure adequate ventilation around the module.
    • Verify that the load is not exceeding the module's 24W output power rating.

7. User Tips

  • For optimal fast charging performance, always use high-quality USB cables that are rated for fast charging.
  • When integrating the module into a custom project, ensure the input power source can reliably deliver the necessary voltage and current for your desired output. For example, to achieve 12V fast charging, your input must be at least 12V.
  • Consider the module's compact size (38x20x10mm) for space-constrained applications like car chargers or DIY power banks.

8. Warranty and Support

This product is manufactured to high-quality standards. For any technical assistance or support, please contact the seller or manufacturer directly. Please refer to your purchase documentation for specific warranty terms and conditions.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.