Dooya DC31

Contents

Dooya DC31 Receiver and Emitter RF433 Wireless System User Manual

Model: DC31 | Brand: Dooya

1. Introduction

This manual provides detailed instructions for the installation, programming, and operation of the Dooya DC31 RF433 Wireless System. This system is designed to control tubular motors commonly used in garage doors and roller shutters. Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Package Contents

The Dooya DC31 Wireless System package typically includes the following components:

  • 1 x Dooya DC31 Receiver
  • 2 x Dooya Emitters (Remote Controls)
  • Necessary wiring for the receiver
Dooya DC31 Receiver and two Emitters with wiring
Figure 1: Dooya DC31 Receiver and two Emitters (remote controls) with included wiring.

3. Specifications

FeatureSpecification
Model NumberDC31 Receiver with Emitters
Voltage110-240V
Wattage0.03W
Frequency433MHz
OriginMainland China
CertificationCE
EU LVD VoltageLow voltage: Below 50Vac or 75Vdc
Battery IncludedNo (for Emitters)
Package Weight0.45 kg
Package Dimensions15 x 15 x 15 cm
Back view of Dooya DC31 Receiver showing model, frequency, and voltage
Figure 2: Back view of the DC31 Receiver, indicating model DC31, 433MHz, and 220V/50Hz.

4. Setup and Installation

4.1 Wiring Diagram

Refer to the following diagram for proper wiring of the Dooya DC31 Receiver with your tubular motor and roller shutter system. Ensure all connections are secure and correctly matched to avoid damage or malfunction.

Wiring diagram for a tubular motor roller shutter door system, showing connections for motor, receiver (DC136), and emitter (DC115A).
Figure 3: Wiring diagram for a typical electric roller shutter door solution. Key components include: Tubular Motor (DM45M-50/12), Drive Adapter (DL210), Driving Tube, Wall Bracket (DZ193), Idler (DW12), Metal Roller Sheet, Guiding Track, Motor Bracket (DZ198), Receiver (DC136), Hand Crank Tie-in (DS15), Hand Crank (DS38), Crown (DH90), and Mini single-channel emitter (DC115A).

Note: The diagram shows a general setup. Your specific motor and accessories may vary. Consult a qualified electrician if you are unsure about any wiring steps.

4.2 Emitter (Remote Control) Programming

Follow these steps to program your Dooya Emitter with the DC31 Receiver:

  1. Select Indicator Light: Identify the first indicator light on the receiver.
  2. Access P2 Key: Open the back cover of the receiver to locate the P2 key on the left side.
  3. Power On and Initiate Pairing: Power on the motor. Press and hold the setting key (P2 key) on the receiver for 3 seconds. The motor indicator light will turn on.
  4. Pair Emitter: Press the PS key on the left side of the emitter once. The motor indicator light on the receiver will flash slowly.
  5. Confirm Pairing: Press the P2 key on the left side of the receiver again. The motor indicator light will flash quickly, indicating successful pairing.
  6. Test Operation: Test the up and down keys on the emitter to confirm successful control of the motor.
Front view of Dooya DC31 Receiver showing indicator lights and buttons
Figure 4: Front view of the DC31 Receiver, showing indicator lights and control buttons (P2, PS keys are internal).

5. Operating Instructions

Once the DC31 Receiver and Emitters are successfully installed and programmed, operating your tubular motor is straightforward:

  • Up Button: Press the 'Up' button on the emitter to raise the roller shutter or open the garage door.
  • Down Button: Press the 'Down' button on the emitter to lower the roller shutter or close the garage door.
  • Stop Button: Press the 'Stop' button (if available on your emitter) to halt the motor's movement at any desired position.

Ensure the line of sight between the emitter and receiver is clear for optimal signal transmission, although RF433MHz typically offers good range.

6. Maintenance

The Dooya DC31 Wireless System is designed for low maintenance. To ensure longevity and reliable operation:

  • Keep the receiver and emitters clean and free from dust and moisture.
  • Avoid exposing the components to extreme temperatures or direct sunlight for prolonged periods.
  • Regularly check the wiring for any signs of wear or damage.
  • Replace emitter batteries as needed (see User Tips).

7. Troubleshooting

If you encounter issues with your Dooya DC31 Wireless System, consider the following:

  • Motor not responding:
    • Check if the receiver is powered on.
    • Ensure the emitter's battery is not depleted.
    • Verify that the emitter is properly programmed to the receiver (refer to Section 4.2).
    • Check all wiring connections to the motor and receiver.
  • Limited range:
    • Ensure there are no major obstructions between the emitter and receiver.
    • Avoid placing the receiver near large metal objects or other sources of RF interference.
  • Indicator light not behaving as expected during programming:
    • Repeat the programming steps carefully.
    • Ensure the P2 and PS keys are pressed correctly and for the specified duration.

8. User Tips

  • Emitter Batteries: The remote control emitters do not come with batteries due to shipping restrictions. Please purchase the required batteries from your local market before attempting to use the emitters.
  • Chromatic Aberration: Product photos are taken from real products, but slight color discrepancies may occur due to lighting and computer screen settings. This does not affect product functionality.

9. Warranty and Support

For technical support, warranty claims, or further assistance, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

This product is CE certified, indicating compliance with European safety, health, and environmental protection requirements.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.