ETENWOLF Zephyr S3C Air Compressor

Contents

ETENWOLF Zephyr S3C Portable Air Compressor

User Manual

1. Introduction

The ETENWOLF Zephyr S3C is a multifunctional portable tire inflation pump designed for a wide range of applications, including passenger cars, SUVs, light-duty pickups, motorcycles, bicycles, and various inflatable items like basketballs and swimming laps. This device features a powerful 7800mAh battery, high-speed inflation at 22L/Min (at 0 PSI), and a maximum pressure of 160 PSI (11 bar). It boasts a 100% duty cycle, allowing for continuous inflation of large tires without interruption. Additionally, the S3C includes a 15W PD fast charging capability and a power bank function for charging other electronic devices. It offers 4 output modes (Car, Bike, Balls, Custom), 3 pressure units (BAR, PSI, KPA), and 3 LED light modes (Illumination, Slow Strobe, SOS).

Please read all instructions and safety warnings carefully before use. For any questions or comments, contact support@etenwolf.com or call (+1) 866-720-9226 (Mon-Fri 8AM-5PM PST).

Register your product at https://etenwolf.com to receive a 1-year extended warranty.

2. Package Contents

Ensure all items are present in the package:

  • ETENWOLF Zephyr S3C Air Compressor x 1
  • USB A to C Charging Cable x 1
  • User Manual x 1
  • 15W Charger x 1
  • Cone Shaped Blowing Nozzle x 1
  • Ball Needle x 1
  • French Copper Adapter x 1
  • T-shaped Quick Connector x 1
ETENWOLF Zephyr S3C Package Contents
Image: ETENWOLF Zephyr S3C Package Contents

3. Product Overview

Familiarize yourself with the components and controls of your ETENWOLF Zephyr S3C Air Compressor.

ETENWOLF S3C Portable Air Compressor with key features
Image: ETENWOLF S3C Portable Air Compressor highlighting 160PSI, 22L/Min, 7800mAh, and compatible uses.
Internal Cooling System Diagram
Image: Diagram illustrating the new cooling system with multi-blade rotating fan, air holes, and various protection features (AI-software, high/low-temperature, over-charge, over-current, over-voltage, short-circuit, over-load protection).

Component Identification:

  1. Unit button
  2. Light button
  3. "-" decrease pressure button
  4. Mode button
  5. Start/pause power button
  6. "+" increase pressure button
  7. Center display
  8. LED work light
  9. Pressure hose
  10. Type-C port (Input)
  11. USB-A port (Output)
  12. Presta valve adapter
  13. Inflation needle
  14. High-pressure tapered nozzle
  15. Manual mode
  16. Car mode
  17. Bicycle mode
  18. Ball mode
  19. Pressure unit
  20. Target input value
  21. Actual pressure value
  22. Battery level indicator
  23. Safety alert symbol

4. Quick Start Guide

Follow these steps for quick and efficient inflation:

  1. Remove Pressure Hose: Take the Pressure hose (09) from its storage channel.
  2. Connect Nozzle: Insert the nozzle (09) clockwise into the item to be inflated.
  3. Activate Machine: Press the Start/pause power button (05) to turn on the compressor.
  4. Select Mode: Press the Mode button (04) to cycle through the 4 different modes: Manual (15), Car (16), Bicycle (17), and Ball (18).
  5. Select Pressure Unit: Press the Unit button (01) to switch between PSI, KPa, and Bar.
  6. Adjust Target Pressure: Use the "-" button (03) to decrease or the "+" button (06) to increase the target pressure value.
  7. Start Inflation: Press the Start/pause power button (05) again to begin inflation.
  8. Automatic Shut-off: The compressor will automatically turn off once the preset pressure value is reached.

Note: The Presta valve adapter (12), inflation needle (13), and high-pressure tapered nozzle (14) are stored in the back side storage panel.

Inflation Steps and Product Dimensions
Image: Visual guide for inflation steps and product dimensions.

5. Operating Instructions

Button Operation Guide

  • Turn ON: Long-press the Start/pause power button (05) for two seconds.
  • Turn OFF: When the inflator is on, long-press the Start/pause power button (05) for two seconds.
  • Pause Inflation: While inflating, press the Start/pause power button (05) once to pause the machine.

Automatic Shut-off Conditions: The inflator will automatically turn off in the following scenarios:

  • 3 minutes of inactivity.
  • Charging cable is accidentally disconnected during charging.
  • 5 minutes of inactivity after being fully charged.
  • 5 minutes of inactivity after being used as a power bank.
  • Inflating for over 5 minutes with actual pressure still below 5 PSI.
  • Inflating for over 5 minutes with actual pressure above 150 PSI.

Preset Pressure Values

The display shows the target input value (20) in a smaller size at the top, and the actual pressure value (21) of the inflated device in a larger size at the bottom.

ModeAdjustable Pressure Range
Car mode8.0-130.0 PSI
Bicycle mode10.0-145.0 PSI
Ball mode3.0-16.0 PSI
Manual mode3.0-160.0 PSI

Memory Function

The ETENWOLF inflator remembers your last target pressure value and unit option. This allows you to change the default pressure setting at any time, and it will be retained for future use.

LED Work Light (08)

The LED work light (08) is located on the front of the inflator. To turn it on, first power on the machine by pressing the Start/pause power button (05), then press the Light button (02).

Light Modes: The LED work light has four different modes:

  • Bright flashlight
  • Ultra-bright flash light
  • Slow strobe light
  • SOS light

Note: The light will automatically turn off after 1 hour. After the first automatic turn-off, you can manually turn on the LED light for a second time. Once manually turned on for the second time, it will not automatically turn off and must be turned off manually.

Power Bank Function

The inflator can function as a power bank to charge your electronic devices such as phones, tablets, laptops, drones, and cameras. It provides a USB-A Output of 5V 2A, 10W.

Note:

  • The inflator needs to be powered on to work as a power bank.
  • After 3 minutes of charging, the display panel will only show the battery level to conserve power.
  • After 5 minutes of fully charging the connected device, the inflator will automatically turn off.

Battery Charging & Indicator

For optimal charging performance, use a 5V 3A 15W PD charger. It takes approximately 3.5 hours to fully charge the built-in battery from 0% to 100%. Using a 5V 2A 10W charger will take approximately 6 hours for a full charge.

The battery level indicator (22) is represented by four bars, with each bar indicating 25% of the battery capacity.

Note:

  • After 5 minutes of inactivity after being fully charged, the inflator will automatically shut off.
  • The inflator cannot be used while it is charging.

6. Pressure Recalibration

Different altitudes can cause variations in pressure readings (1-3 PSI). In high-altitude areas (especially above 5000 ft/1524 meters), you can recalibrate the pump's pressure sensor.

Recalibration Steps:

  1. Power on the pump (05).
  2. Hold the Light button (02) and Mode button (04) simultaneously for 10 seconds.
  3. The screen will restart, indicating successful recalibration.

Important Notes:

  • Power off the pump before starting recalibration.
  • The Pressure hose (09) must NOT be connected to any item during recalibration. Any pressure on the hose will disable the process.
  • A charged battery or other power source is required for recalibration.
  • There is no memory for new recalibration settings. Once the power is turned off, it will reset to sea level calibration (0 ft/meters altitude).

7. Safety Instructions

  • This product is not a toy and should not be used by children. Users should be above 16 years old. Keep a safe distance between children and the inflator while inflating.
  • The product contains a built-in lithium battery. Do not place the product into fire or dispose of the battery improperly.
  • Overheating or water ingress can increase the risk of fire or explosion. Keep the product away from heat sources and do not leave it in a hot car for prolonged periods. If the inflator becomes very hot, turn it off immediately.
  • Store the product within temperatures ranging from -10°C to 60°C (14°F to 140°F). Extreme temperatures can damage the battery and shorten its lifespan.
  • For long-term storage, charge the inflator at least once every three months to maintain battery performance.
  • The product has a built-in DC motor which may generate sparks. Do not use it in environments with dust or gas that are liable to explode.
  • If there is an unusual noise or the temperature becomes very high during inflation, turn off the inflator immediately.
  • Before setting the inflation pressure value, ensure the correct pressure unit is selected. Mixing up PSI and Bar can lead to dangerous overinflation.
  • Do not leave the pump unattended while it is in operation.
  • Use the product in a dry and clean environment. Sand and dust can cause damage. Do not wash the product with water.
  • Only use ETENWOLF's charger or other certified PD chargers, and the included charging cable. Malfunctions caused by non-compliance with these requirements are not covered by the warranty.
  • To reduce the risk of electric shock, do not expose the device to rain. Store indoors.

8. Specifications

NameAir Inflator
ModelZephyr S3C Air Compressor
Brand NameETENWOLF
Item TypePUMPS
Dimensions (L x W x H)6.18 inch x 4.8 inch x 7.79 inch (134 x 171 x 96mm)
Item Weight1.3kg
Inflation Pressure Range3.0-160.0 PSI / 0.20-11.00 Bar
Operating TemperatureCharging: 0°C-45°C (30°F-113°F)
Discharging: -20°C-74°C (-4°F-165°F)
Storage Temperature-10°C-60°C (14°F-140°F)
High Pressure Air Tube Length0.9 meters
Battery Capacity7800mAh
Working NoiseLower than 85dB within 1 meter
InputType-C: 5V 3A
OutputUSB-A: 5V 2A
Charging Time15W: 3.5 hours / 10W: 6 hours
Continuous Working TimeApproximately 25 minutes at 20-50 PSI in 25°C ambient temperature, under full charge
Sensor Accuracy±1 PSI
OriginMainland China

9. Troubleshooting

Refer to the table below for common issues and their solutions:

ProblemSolution
Slow inflation speed
  • Check if the item being inflated is leaking.
  • Check if the air nozzle connection is tightened.
  • Check if the inflation hoses are broken.
  • Check if the ventilation slots are blocked.
Air compressor turns on, but does not inflateCheck if the pressure of the item being inflated exceeds the preset pressure.
Unable to increase or decrease the preset pressure
  • Ensure the correct mode is chosen, and the preset value does not exceed the range.
  • Select manual mode and adjust the preset value within the 3-160 PSI range.
The inflator inflates but the pressure shown on the display is zero.If the air pressure is under 3 PSI, the display will show zero due to the pump's minimum pressure range.
The battery level indicator does not show on the screen after charging.Use a certified ETENWOLF charger or standard charger, and the included charging cable. Try to charge it again.
Air leakage when connecting the high-pressure air hose.Tighten the air nozzle.
Unable to charge other devices
  • Check if the battery is sufficient.
  • Verify if the charging device is compatible with 5V 3A output.
  • The inflator cannot be used as a power source while it is being charged.
  • Use the original charging cable provided with the charging device for charging.
Safety alert symbol light on display shows E08 error codeAfter shutting down and restarting, if the issue persists, send the device for factory repair. (Motor malfunction warning)
Display shows E10 error codeMotor malfunction warning. If issue persists after restart, send for factory repair.
Display shows E11 error codeLow-temperature charging protection. Restore temperature to above 0°C before continuing charging.
Display shows E12 error codeHigh-temperature charging protection. Restore temperature to below 45°C before continuing charging.
Display shows E13 error codeLow-temperature discharge protection. Restore temperature to above -20°C before continuing with inflation/charging other devices.
Display shows E14 error codeHigh-temperature discharge protection. Restore temperature to below 58°C before continuing with inflation/charging other devices.
Display shows E15 error codeAir pump exceeded working time. Warning icon flashes for 30 seconds. Check for leaks in inflated item.
Display shows E16 error codeOverpressure protection. Will return to normal after pressure release.
Display shows E17 error codeHigh-pressure operation exceeded working time. Warning icon flashes for 30 seconds. Check if inflated item is functioning abnormally.
Display shows E18 error codeBattery damage warning. Device will shut down after 30 seconds flashing. Send for factory repair.

10. User Tips

  • Efficiency: Users report the S3C is quiet and fast, making tire pressure adjustments for cars, motorcycles, and bicycles very convenient.
  • Ease of Use: The device is described as easy to use and intuitive, even for first-time users.
  • Quality: Many users are pleasantly surprised by the quality of the product relative to its price.
  • Motorcycle Tires: It performs exceptionally well on motorcycle tires, inflating them quickly and accurately.

11. Warranty and Support

2-Year Coverage

ETENWOLF provides a 2-year warranty from the date of purchase. During this period, we offer timely and effective online after-sale service. We will repair or replace any defective product (due to manufacturing fault) within this warranty period.

Contact Information

Manufacturer: Guangdong Bestek Technology Co., Ltd
Address: No.1, North Gaopu 8th Road, Yuancheng Industrial Park, Heyuan City, Guangdong, P.R.China

Brand Owner: Mozhen Technology (Shenzhen) Co., LTD
Address: CN-503, Floor 5, Building 4, Tianan Yungu Industrial Park Phase II, Gangtou Community, Bantian Street, Longgang District, Shenzhen, Guangdong, CN

Customer Support:
Phone: (+1) 866-720-9226 (Mon-Fri 8AM-5PM PST)
Email: support@etenwolf.com
Website: https://etenwolf.com
Facebook: www.facebook.com/etenwolftools

Made in P.R.C

We are committed to providing you with professional and efficient service!

For a digital copy of this user manual, please refer to the PDF available at: ETENWOLF Zephyr S3C User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.