1. Introduction
The RHUNDO RW-T11 is a versatile wireless digital temperature display designed for monitoring temperatures in various environments, including vehicles (car, truck, RV), homes, or outdoor spaces. It features an IPS TFT color display, supports up to three wireless temperature probes, and includes high/low temperature alarm functions. This manual provides detailed instructions for setting up, operating, and maintaining your device.

2. Package Contents
Before you begin, please check the package for the following items:
- RHUNDO RW-T11 Display Unit
- USB Type-C Power Cable
- User Manual (this document)
- Adhesive Pad for mounting
- Wireless Temperature Probe(s) (quantity depends on model purchased: 1, 2, or 3)

3. Setup
3.1 Powering the Display Unit
The RW-T11 display unit does not have a built-in battery and must be powered via its USB Type-C input port. Connect the provided USB Type-C cable to the display unit and a suitable power source (e.g., car USB port, USB wall adapter, power bank).

Note: When using a power bank, ensure it supports continuous low-current output. Some power banks may shut down if the device's operating current is too low.
3.2 Installing Batteries in Wireless Sensors
Each wireless temperature sensor (model RTW-15) requires a CR2032 battery. To install:
- Carefully open the sensor casing.
- Insert a CR2032 battery with the positive (+) side facing upwards.
- Close the sensor casing securely.

3.3 Adding Wireless Temperature Probes
To connect the wireless probes to the display unit:
- On the display unit, navigate to the main settings menu.
- Select "Add Sensor".
- The display will show "Searching" and a countdown.
- Press and hold the button on the wireless sensor you wish to add.
- Once paired, the sensor will appear on the display. Repeat for additional sensors.


4. Operating Instructions
4.1 Main Display Interface
The main screen shows real-time temperature readings from connected sensors. It typically displays:
- Current temperature for each channel.
- Highest and lowest temperatures recorded for each channel within the preset time period.
- Wireless signal strength for each sensor.

4.2 Button Definitions
The device features three buttons for navigation and control:
- Top Button: Short press to switch between channels in temperature curve mode.
- Middle Button: Short press to switch to temperature curve mode from the home screen. Long press to exit temperature curve mode and return to the home screen.
- Bottom Button: Used for confirmation or scrolling down in menus.

4.3 Temperature Curve Mode
This mode displays a graphical representation of temperature changes over time for each channel. To access:
- From the home screen, short press the middle button to enter temperature curve mode.
- Use the top button to switch between different sensor channels.
- The graph shows temperature fluctuations, along with average, lowest, and highest temperatures during the recording time.
- Long press the middle button to exit curve mode and return to the home screen.

Recording Time Intervals: The interval between recorded points varies with the total recording duration set:
| Recording Time | Interval |
|---|---|
| 1 hour | 12 seconds |
| 2 hours | 24 seconds |
| 4 hours | 48 seconds |
| 6 hours | 72 seconds |
| 12 hours | 144 seconds |
| 24 hours | 288 seconds |
| 2 days | 576 seconds |
| 3 days | 864 seconds |
| 7 days | 2016 seconds |
| 14 days | 4032 seconds |
| 30 days | 8640 seconds |
Important Notes on Recording:
- Changing the recording duration in settings will delete previously recorded data. You will be prompted for confirmation.
- Recording time is based on the device's power-on duration. If the device is powered off, recording stops and resumes when powered on again.
4.4 High & Low Temperature Alarms
You can set individual high and low temperature alarms for each channel:
- Navigate to the "Alerts" menu in the settings.
- Select the desired channel (1, 2, or 3).
- Set the low and high temperature thresholds.
- If the temperature for a channel falls below the low threshold or rises above the high threshold, an alarm will activate.
- To mute an active alarm, press the middle button. The temperature reading will continue to blink.

4.5 Display Settings
Customize your display preferences:
- Access the "Display" menu from the main settings.
- Options include:
- Temperature Unit: Switch between Celsius (°C) and Fahrenheit (°F).
- Brightness: Adjust display brightness (levels 1-5).
- Display Rotation: Rotate the screen orientation.
- Temp Curve Rec. Time: Set the duration for temperature curve recording (e.g., 12 Hr, 24 Hr).

4.6 Wireless Communication
The RW-T11 uses a proprietary 2.4G wireless communication protocol, eliminating the need for Bluetooth or Wi-Fi. It offers a transmission range of approximately 40 meters (131 feet) in open, unobstructed areas and can penetrate 2-3 walls, providing good coverage in typical home environments.

5. Maintenance
5.1 Cleaning
To clean the display unit and sensors, use a soft, dry cloth. Do not use abrasive cleaners, solvents, or immerse the devices in water (unless the sensor is a waterproof model).
5.2 Sensor Battery Replacement
When the sensor battery is low, replace it with a new CR2032 battery, following the installation steps in Section 3.2.
6. Troubleshooting
- Display Unit Not Turning On: Ensure the USB Type-C cable is securely connected to a compatible power source. Verify the power source is active.
- No Sensor Readings: Check if the sensor batteries are correctly installed and not depleted. Ensure sensors are within the wireless range (approx. 40m unobstructed) and not experiencing excessive interference. Try re-pairing the sensors (Section 3.3).
- Inaccurate Temperature Readings: Ensure sensors are placed in appropriate locations, away from direct heat sources or extreme drafts that might skew readings.
- Alarm Not Functioning: Verify that the high/low temperature thresholds are correctly set in the "Alerts" menu (Section 4.4).
7. Specifications
| Feature | Specification |
|---|---|
| Product Name | Digital Temperature Display |
| Model | RW-T11 |
| Material | ABS, PC |
| Input Voltage | DC4V-6V |
| Display Type & Resolution | TFT IPS 320*170 |
| Operating Temperature | -20°C to 70°C (-4°F to 158°F) |
| Wireless Range | 40m (131ft) (no obstacle) |
| Size (L*W*T) | 60*34*9.5mm (2.36*1.34*0.37in) |
| Display Information | In Temperature, Outside Temperature |
| Dial Display | Digital |
| Placement | Dashboard |
8. User Tips
- For optimal wireless performance, try to minimize obstacles between the display unit and the sensors.
- Consider using the waterproof sensor model for outdoor or high-humidity environments.
- Regularly check sensor battery levels to ensure continuous temperature monitoring.
- The display is suitable for various applications, including monitoring car interiors, outdoor conditions, or even the temperature inside a car cooler.

9. Warranty and Support
For detailed warranty information and further support, please refer to the official user manual PDF available at: RHUNDO RW-T11 User Manual (PDF).