1. Introduction
The SpeedyBee F405 WING APP/MINI Flight Controller is an advanced control system designed for RC fixed-wing model airplanes. It offers easy installation, wireless configuration, and supports both iNAV and ArduPilot firmwares, providing flexibility for various flying styles from FPV racing to advanced VTOL operations. This manual provides detailed instructions for setting up, operating, and maintaining your flight controller.
2. Package Contents
Verify that all the following items are included in your package:

Figure 2.1: SpeedyBee F405 WING APP/MINI Package Contents
- SpeedyBee F405 WING FC board x1
- SpeedyBee F405 WING PDB board x1
- SpeedyBee F405 WING Wireless board x1
- SpeedyBee F405 WING USB extender x1
- 90 Degree pin Header (3x12) x1
- Straight pin header (1x12) x3
- M2x4 small head cross screw x10
- White straight pin header (1x4) x1
- M2 x 12 copper Standoff Spacer x5
- M3x4mm Silicone Grommets x5
- 8pin SH1.0 USB Extender Cable (80mm) x1
- 6pin SH1.0 Analog VTX Cable (250mm) x1
- 6pin SH1.0 GPS Module Cable without Connector on another end (250mm) x1
- 6pin Digital VTX Cable (250mm) x1
- 4pin SH1.0 to 3+2pin JST1.25 FPV Cam Cable (250mm) x1
- 6pin GH1.25 Telemetry module Cable (200mm) x1
- 4pin Dupont single-head Cable (150mm) x1
- Double-sided tape for isolating pins and cables (32x9x1mm) x1
3. Specifications
3.1. SpeedyBee F405 WING FC Board

Figure 3.1: F405 WING FC Board Specifications
| Feature | Description |
|---|---|
| MCU | STM32F405, 168MHz, 1MB Flash |
| IMU (Gyro&Accelerometer) | ICM-42688-P |
| Barometer | SPL006-001 |
| OSD Chip | AT7456E |
| Blackbox | MicroSD Card Slot |
| UART | 6 sets (USART1, USART2, USART3, UART4, UART5, UART6 (Dedicated for Wireless board Telemetry connection)) |
| I2C | 1x Used for magnetometer, digital airspeed sensor |
| ADC | 4x (VBAT, Current, RSSI, Analog AirSpeed) |
| PWM | 12x (11+1 "LED" pad) |
| ELRS/CRSF receiver | Supported, connected to UART1 |
| SBUS | Built in inverter for SBUS input (UART2-RX) |
| LED | 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator (Red) 1x RGB |
| RSSI | Supported, Named as RS. |
| Supported FC Firmware | iNAV: SpeedyBeeF405WING (default) ArduPilot: SpeedyBeeF405WING |
3.2. SpeedyBee F405 WING PDB Board

Figure 3.2: F405 WING PDB Board Specifications
| Feature | Description |
|---|---|
| Input voltage range | 7-36V (2-6S LiPo) |
| Battery Voltage Sensor | Connect to FC board VBAT, 1K:10K (Scale 1100 in iNav, BATT_VOLT_MULT 11.0 in ArduPilot) |
| Battery Current Sensor | 90A continuous, 215A peak. Connect to FC board Current (Scale 195 in iNav, 50 A/V in ArduPilot) |
| TVS Protective diode | Yes |
| FC BEC output | Output 5.2V +/- 0.1V DC Continuous current 2.4 Amps, 3A Peak. Designed for FC, Receiver, GPS module, AirSpeed module, Telemetry module, WS2812 LED_Strip |
| VTX BEC output | Output 9V +/- 0.1V DC Continuous current 1.8 Amps, 2.3A Peak. Voltage adjustable, 9V Default, 12V or 5V via jumper. Designed for Analog Video Transmitter, Digital Video Transmitter, Camera. |
| Servo BEC output | Output 4.9V +/- 0.1V DC Continuous current 4.5 Amps, 5.5A Peak. Voltage adjustable, 4.9V Default, 6V or 7.2V via jumper. Designed for Servos. |
3.3. SpeedyBee F405 WING Wireless Board

Figure 3.3: F405 WING Wireless Board Specifications
| Feature | Description |
|---|---|
| Wireless Configuration | BLE mode (connect to Speedybee APP), Wi-Fi mode (connect to QGroundControl APP, Speedybee APP, MissionPlanner, etc.), Classic Bluetooth SPP mode (connect to QGroundControl APP, MissionPlanner). (Long press BOOT button for 6 seconds to switch modes). |
| LED strip controller | 4x WS2812 LED strip connectors, adjustable colors and flashing modes. (Short press BOOT button to switch effects, long press 2 seconds to switch modes). |
| On-board battery level indicator | 4x RGB indicator LED for battery level display by number of lights. |
3.4. Dimensions

Figure 3.4: Flight Controller Dimensions
- Length: 52mm
- Width: 32mm
- Thickness: 19mm
4. Setup & Installation
4.1. Physical Assembly
The SpeedyBee F405 WING system features a stacked design for compact integration. Carefully align the pin headers and connect the FC board, PDB board, and Wireless board. Ensure all connections are secure.

Figure 4.1: Assembled Flight Controller with Wiring
4.2. Wiring Peripherals
The flight controller is designed for plug-and-play connectivity, minimizing the need for soldering. Utilize the provided cables and pin breakouts for connecting various peripherals.

Figure 4.2: Peripheral Wiring Example
- UART Ports: The FC board features 6 UART ports for easy expansion. These can be used to connect external modules such as GPS, Digital VTX, Analog VTX, and Telemetry modules.
- ELRS/TBS Receiver: Directly plug your ELRS/TBS receiver into the UART1 port.
- PWM Outputs: Up to 11 PWM outputs are available for motor and servo control. Refer to the detailed output settings in the full product documentation for specific configurations for conventional layout planes, V-tail planes, planes with flaperons, and VTOLs.

Figure 4.3: MCU Pin Breakout and UART Assignments
4.3. Firmware Selection
The SpeedyBee F405 WING supports dual firmwares: iNAV and ArduPilot. You can choose the firmware that best suits your flying needs:
- iNAV: Ideal for handling FPV flight easily, suitable for Wing Racing and Formation Flying.
- ArduPilot: Recommended for advanced capabilities, including Autopilot and Long-Range Flights, and supports VTOL functions.

Figure 4.4: iNAV vs. ArduPilot Firmware Comparison
4.4. LED Strip Installation
The flight controller includes 4x WS2812 LED strip connectors, allowing for easy installation of LED strips without soldering. These can be used to enhance visibility and style of your aircraft.

Figure 4.5: LED Strip Integration
5. Operating Instructions
5.1. Wireless Configuration
The SpeedyBee F405 WING offers convenient wireless configuration via mobile apps. Long press the BOOT button for 6 seconds to switch between the following wireless modes:
- BLE Mode: Connects to the Speedybee APP.
- Wi-Fi Mode: Connects to QGroundControl APP, Speedybee APP, MissionPlanner, etc.
- Classic Bluetooth SPP Mode: Connects to QGroundControl APP, MissionPlanner.

Figure 5.1: Wireless Configuration via App
5.2. LED Strip Control
The BOOT button also controls the LED strip effects:
- Short press: Switches between different LED effects.
- Long press (2 seconds): Switches between LED modes.
- Long press (3 seconds): Switches to FC control for LED lights.
5.3. Battery Level Indicator
The flight controller is equipped with a 4-level RGB LED battery indicator to quickly check the remaining LiPo battery power. The number of lit LEDs corresponds to the battery level.

Figure 5.2: 4-Level LiPo Battery Indicator
5.4. VTOL Functionality (ArduPilot)
For users utilizing ArduPilot firmware, the F405 WING supports VTOL (Vertical Take-Off and Landing) functionality. This allows for manual or autonomous control of VTOL plane takeoff and landing using ArduPilot's QStabilize, QLoiter, and QRTL modes. Various plane models, including Tiltrotor, Quadplane, and flying wing tail-sitter, can be customized.

Figure 5.3: VTOL Operation
6. Maintenance
- Voltage Detection Calibration: Always calibrate the flight controller's voltage detection before relying on the on-board battery level indicator for accurate readings.
- Heat Dissipation: The multi-layer PCB design includes dedicated heat dissipation areas. Ensure these areas are not obstructed to maintain cool and stable operation.
- Firmware Updates: Regularly check for and apply firmware updates for both iNAV and ArduPilot to ensure optimal performance and access to the latest features and bug fixes.

Figure 6.1: Multi-layer PCB Design for Optimal Performance
7. Troubleshooting
- Connectivity Issues: If you encounter difficulties with mobile app tuning, try switching between BLE, Wi-Fi, and Classic Bluetooth modes by long-pressing the BOOT button for 6 seconds. Ensure your app (Speedybee APP, QGroundControl, MissionPlanner) is compatible with the selected mode.
- Lost Video Signal: If experiencing signal loss at a distance, utilize OpenTX/EdgeTX telemetry data to monitor your plane's status and aid in recovery. Ensure your ELRS/TBS receiver is correctly plugged into UART1 and configured for telemetry.
- LED Strip Malfunction: If LED strips are not functioning as expected, short press the BOOT button to cycle effects or long press for 2 seconds to switch modes. If still unresponsive, long press for 3 seconds to switch to FC control for LED lights.
8. User Tips
- The SpeedyBee F405 WING is noted for its excellent build quality and features, offering great value for its price point.
- While shipping times may vary, the product's quality often justifies the wait for a better price.
- If you have concerns about product authenticity due to packaging, verify the chips on the PCB boards, which are generally reported as authentic.
9. Warranty & Support
For warranty claims, technical support, or further assistance, please contact the seller or manufacturer directly. Keep your purchase records for reference. Specific warranty terms and conditions may vary by region and seller.