AUTOPMALL MV750G

Contents

MiCODUS MV750G 4G GPS Tracker

User Manual V1.0

Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of your new MiCODUS MV750G 4G GPS Tracker. Designed for reliable vehicle tracking and security, the MV750G offers a range of features including real-time tracking, anti-theft alarms, and remote control capabilities. Please read this manual thoroughly to ensure proper installation and optimal performance of your device.

Main Features

  • 2G+4G Network Support: Utilizes both 2G GSM/GPRS and 4G LTE CAT1 for broad compatibility and reliable connectivity.
  • Advanced Positioning: Integrates GPS, BDS, and GLONASS for high-sensitivity and precise tracking.
  • Remote Fuel Cut-Off/Resume: Allows remote control over vehicle fuel/power for enhanced security.
  • Real-time Tracking & Historical Route Playback: Monitor your vehicle's location in real-time and review past routes for up to 180 days.
  • Vibration Alarm: Alerts you to unauthorized movement or impacts.
  • IP67 Waterproof: Designed to withstand harsh environmental conditions, submersible in 1 meter of water for 30 minutes.
  • Remote Door Lock & Unlock: Conveniently control vehicle doors remotely.
  • Anti-Jammer: Detects and alerts against signal jamming attempts.
  • Geo-fence: Set up virtual boundaries and receive alerts when the vehicle enters or exits defined areas.
  • Ignition On/OFF Alarm: Notifies you when the vehicle's ignition is turned on or off.
  • Low Voltage Alarm: Alerts you if the vehicle's battery voltage drops below a set threshold.
  • Overspeed Alarm: Notifies you if the vehicle exceeds a predefined speed limit.
  • Open Door Alarm & Door Status Detection: Provides alerts if a door is opened without authorization.
  • Buzzer Alarm: Optional accessory for audible alerts.
  • ACC Status Detection: Detects ignition status (ON/OFF) and sends alerts.
  • 1500pcs GPS Data Storage: Stores data in network blind zones for accurate route reconstruction.
  • OTA Remote Upgrade: Supports over-the-air firmware updates for bug fixes and new features.
MiCODUS MV750G 4G GPS Tracker with feature icons
Overview of MiCODUS MV750G features including IP67 waterproof, door status detection, geo-fence, SOS emergency alarm, door lock & unlock, buzzer alarm, fuel/power cut & restore, overspeed alarm, and engine on/off alarm.

Package Contents

Please check the package contents upon receipt to ensure all items are present:

  • GPS Main Unit x 1
  • Function Cable x 1
  • Buzzer (Optional) x 1
  • SOS Button Cable (Optional) x 1
  • Relay (Optional) x 1
  • User Guide x 1
  • Genuine Packing Box x 1
MiCODUS MV750G package contents including tracker, relay, wiring harness, and user manual
The MV750G tracker and its included accessories.

Specifications

Table of Product Specifications for MV750G
Detailed product specifications for the MiCODUS MV750G.
Product Specifications - MiCODUS MV750G
CategoryParameterValue
Device InformationModelMV750G
Weight47.6g
Dimensions90.8(L)*28mm(W)*16mm(H)
BatteryBuilt-in 3.7V 140mAh Polymer Battery
Working ParametersWorking Voltage9-95V DC
Working Current12V/Average 30mA
Sleep Current12V/Average 8mA
Working Temperature-20°C - 75°C
Working Humidity10%-85%RH
Cellular SpecificationsBuilt-in Memory1500pcs GPS data can be stored at network blind area
SIM CardNano SIM
Cellular AntennaBuilt-in, FPC
Communication ModuleQUECTEL EG915
Working Frequency2G GSM/GPRS: 850/900/1800/1900MHz, 4G LTE CAT1: B1/B2/B3/B4/B5/B7/B8/B28/B66
GNSS SpecificationsPositioning ModuleZhongke Microelectronics AT6558R
GNSSGPS+BDS+GLONASS
GPS FrequencyL1: 1575.42±1.023MHz
BDS FrequencyB1:1561.098±2.046MHz
Satellite Channels32
Hot/Cold Start<1s, <32s @ Open Sky
GNSS AntennaBuilt-in Ceramics GNSS Antenna, 25mm*25mm*4mm
Positioning TypeGNSS+BDS+LBS+AGPS
AccuracyLocation accuracy: <10m (1σ), Timing accuracy: <30ns (1σ), Speed accuracy: <0.1m/s (1σ)
CertificationCE
GPS Geographic LocationEurope
External InterfaceACC Detection Input1 ACC detection line
Cut-off Fuel/Electric Circuit1 Low output line (relay control line)
SOS1 Low detection line (SOS alarm line)
Remotely Lock/Unlock Door1 Low detection line
Door Status Detection1 Digital input

Setup

SIM Card Requirements

To ensure your tracker functions correctly, please obtain a suitable SIM card from your local provider. The SIM card must meet the following criteria:

  • It must be compatible with 4G LTE or 2G GSM networks.
  • SMS, call, and internet data traffic must be enabled on the SIM card.
  • The caller ID display feature must be enabled.
  • Any PIN code on the SIM card must be removed.
  • Use a Micro size SIM card for the tracker.
  • Inquire with your SIM card provider for the exact and correct APN (Access Point Name) information.
Image showing different SIM card sizes: Nano, Micro, and Normal SIM
Ensure you use a Micro SIM card and remove any PIN code.

SIM Card Installation

  1. Open the tracker casing carefully to access the SIM card slot.
  2. Insert the prepared Micro SIM card into the designated slot.
  3. Once the device is online and configured, you can close the cover.
Internal view of the MV750G tracker showing the SIM card slot and circuit board
Internal view of the tracker with SIM card slot.
Image showing the MV750G tracker with a SIM card inserted and the casing closed
The MV750G tracker with SIM card inserted and ready for use.

NOTE: Please just stick the cover after you have successfully managed to get the device online!

Wiring

Proper wiring is crucial for the tracker's functionality. Refer to the diagram below for correct connections. It is very important to connect the tracker with an external power source of no less than 12V for power supply before operation.

Wiring diagram for the MiCODUS MV750G GPS tracker, showing connections for power, ACC, SOS, door status, relay, and optional buzzer
Wiring diagram for the MV750G tracker.

NOTE: After installing the SIM card correctly, it is very important to connect the tracker with external power no less than 12V for power supply before operation!

Installation Recommendation:

  • The device should face up to the sky for optimal GPS signal reception.
  • Avoid placing the device behind metal thermal barriers or heating layers of the windshield, as this can affect the signal.
  • Common installation locations include: under the front windshield, under the rear windshield, inside the door pedal, around the dashboard, inside the taillight component or plastic, under the pedal, inside the headlight, or inside the front cover.

Configure APN

Obtain the exact correct APN name from your local SIM card provider. Place the tracker in an area with good signal reception and configure the APN using the following SMS commands:

SMS Command FormatReplyExampleNote
APN,ApnName,User,Password#SET APN OKAPN,orange,orange,orange#If the SIM card has APN user and APN password, then use this command.
APN,ApnName#SET APN OKAPN,internet#If the SIM card operator doesn't have APN user and APN password, then please use this command.

Note: The APN information is very important. It must be 100% correct to match the SIM card of the tracker. If you configure the wrong APN, the tracker will reply "SET APN ok" but it will not be able to get online!

Operating Instructions

Indicator Status Description

The device uses LED indicators to show its current status:

LEDEventState
CELL LED (YELLOW)Searching for networkFlash every 1 second
Network has been registeredSolid
GPS LED (BLUE)GPS is in fixingFlash every 1 second
GPS has fixedSolid
ALL LEDDevice is working but stopped more than 5min
Device has not been turn onALL LED TURN OFF
Device ran out of battery

Functions Explanation

a. Cut Off Fuel/Resume Fuel

This function allows you to remotely cut off or restore the vehicle's fuel/power, which can be used to prevent theft or troubleshoot risks.

  • Set Center Number: First, set a center number using the SMS command: CENTER,password,A,center number#
  • Send Command: From the set center number, send the SMS command: RELAY,A#
    Where A can be:
    • 0: Resume Fuel
    • 1: Cut Off Fuel Immediately
    • 2: Cut Off Fuel Safely (cuts off fuel only when speed is below 20km/h or vehicle is stationary if GPS is fixed)
Smartphone screen showing 'Cut Off Fuel' command in an app, with a thief attempting to steal a car in the background.
Remotely cut off or restore fuel/power to prevent theft.

b. Vibration Alert

This alert function works when the tracker is stationary. To use it:

  • Configure SOS Numbers: Set up to 3 SOS numbers using the SMS command: SOS,A,1st number,2nd number,3rd number#
  • Enable Arm Mode: Send the SMS command: ARM# to enable the device to enter arm mode.
  • Configure Alarm Ways: Use SENALM,[A][,M]#. A=ON/OFF (default: OFF), M=0/1/2 (0: GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+phone call, default:1).
  • Keep the device stationary for more than 5 minutes to enter sleep arm mode.
  • If vibration is detected, the tracker will send vibration alarm messages.

c. Open Door Alarm

The device can detect if an unauthorized car door is opened and send an alert.

  • Command Format: DOORALM,A,M#
    Where A=ON/OFF (default: ON), M=0/1/2 (0: GPRS only, 1: SMS+GPRS, 2: SMS+GPRS+Call, default:1).
  • For example, DOORALM,ON,1# means that when the door opens, an alarm message will be sent via SMS and to the server.
Top-down view of a car with a phone displaying a 'DOOR OPEN ALARM!' message, indicating door status detection.
Alerts for unauthorized door opening.

d. Engine Start and Flameout Alarm

This feature detects the ACC (Accessory) status of the vehicle and sends alerts for engine start or flameout.

  • Command Format: ACCALM,A,B,M#
    Where A=ON/OFF (default: ON), B=0/1/2 (0: ACC ON Alarm, 1: ACC OFF Alarm, 2: ACC ON&OFF Alarm, default:2), M=0/1/2 (0: Server only, 1: SMS+Server, 2: SMS+Server+Call, default:1).
  • For example, ACCALM,ON,2,1# means that when the device detects engine start or flameout, it will send an alarm message via server and SMS.
Hand pressing a car engine start button, with a phone displaying an 'ENGINE START ALARM!' message, indicating ACC status detection.
Alerts for engine start/stop events.

e. Remote Door Lock/Unlock

Control your vehicle's doors remotely with a single click, whether you've forgotten to lock it, need to authorize access, or for anti-theft purposes.

Smartphone screen showing 'Remote lock door' command in an app, with a person attempting to open a car door with a tool in the background.
Remote door lock/unlock functionality via the app.

f. Live Tracking and Playback

The MiCODUS MV750G allows you to track your vehicle in real-time on Google Maps and review up to 180 days of historical routes, helping you monitor trips and stops.

Smartphone and desktop screens displaying real-time GPS tracking and historical route playback on maps, with a car driving on a scenic road.
Real-time tracking and 180-day historical route playback.

g. 1500pcs of Data Storage

The device features signal blind zone data storage, which ensures more accurate positioning and clearer routes even when network coverage is lost.

Image depicting a car driving through a tunnel, illustrating how the tracker stores data in 'blind areas' to ensure continuous tracking.
Data storage for accurate positioning in network blind zones.

h. OTA Remote Upgrade

The MV750G supports OTA (Over-The-Air) upgrades to fix bugs and add new features, ensuring the device remains in optimal condition without physical intervention.

Hand holding a smartphone with cloud and network icons, representing OTA remote upgrade functionality for the tracker.
Supports OTA upgrades to keep the device updated.

i. Multiple Alarms

The tracker supports various alarm methods, including calls, SMS, platform notifications, and email, for comprehensive security alerts.

Six panels illustrating different alarm types: Overspeed Alarm, Movement Alarm, Vibration Alarm, Power Failure Alarm, Geo-fence, and Low Voltage Alarm.
Various alarm types supported by the MV750G.

j. Tracking Platform Usage

The MV750G includes a first-year free tracking platform. After the first year, please contact the seller to renew the service. You can log in using the ID number and password found on the device label. If no password is provided, try the default password '123456'.

A demo account is available on the login page for you to experience the platform's features.

MiCODUS Tracking Software interface shown on various devices (smartphone, tablet, laptop) with icons for Realtime Tracking, History Playback, Geo-fence, Distributor Account, and Monitoring Center.
MiCODUS Tracking Software for web and mobile.
Video demonstrating the features of the MiCODUS MV750G tracker, including SIM card slot, IP67 waterproof, remote lock/unlock, SOS button, real-time tracking, and route playback.

Full SMS Commands List

The following tables list all available SMS commands for configuring and controlling your MiCODUS MV750G tracker.

Setting Commands

FunctionsCommand FormatExplanation
APN SettingAPN,Network name[,name,password]#APN,CMNET# (if no name & Password)
APN,internet,internet,internet# (if with name & Password)
Server SettingIf set with Domain Name: SERVER,1,Domain,Port#SERVER,1,d.micodus.net,7700#
If set with IP: SERVER,0,IP,Port#SERVER,0,47.254.77.28,7700#
Check IMEIIMEI#DEVICE IMEI No. : 0123456789
Change IMEIIMEICHG,354188046912460#NEW IMEI No. : 354188046912460
Restore factory settingsFACTORY#RESTORE FACTORY SETTINGS OK
Restart deviceRESTART#RESTARTING...1 MINUTE WILL BE OK
Internet Traffic SwitchTRAFFIC,ON#OPEN TRAFFIC OK
TRAFFIC,OFF#CLOSE TRAFFIC OK
Time Zone SettingGMT,A,B,C#Example:GMT,E,8# (Means East +8 zone, no half time zone)
GMT,W,9,30# (Means West -9.5 zone, has half time zone)
A: E / W, E: East time zone, W: West time zone
B: 0 ~ 12; whole time zone
C: 0/15/30/45, half time zone
Set the angle uploadANGLEREP,X,A,B#Example: ANGLEREP,ON,30,3# (Means the tracker will send a data supplement when the angle change exceeds 30 degrees and lasts for 3 seconds)
X=ON/OFF, default: ON;
A=5~180 degrees, diversion angle degree, default: 30 degrees;
B=2~5 seconds, detecting time, default: 3 seconds;
ANGLEREP,OFF#CANCEL UPLOAD ANGLE OK
Mileage StatisticsMILEAGE,A,B#Example: MILEAGE,ON,5000# (Means enable the mileage statistics feature, the mileage initial value is 5000km)
A=ON/OFF, On/Off mileage calculation, default: Off
B=0~999999, Mileage initial value, unit: km; default: 0, mileage return to zero
MIELEAGE#Query current mileage
Add SOS Administrator NumberSOS,A,1st number,2nd number,3rd number#Example: Set 3 numbers at a time: SOS,A,13800138000,13800138001,13800138002#
Set the first number separately: SOS,A,13800138000#
Set the second number separately: SOS,A,,13800138001#
Delete SOS Administrator NumberSOS,D,1st number,2nd number,3rd number# or SOS,D,1,2,3#Example: Directly delete the number: SOS,D,13800138000#
Delete 1st number: SOS,D,1#
Delete 2nd number: SOS,D,2#
Add Center NumberCENTER,password,A,center number#Example: CENTER,888888,A,+8613800138000#
Note: Please set up the center number with the country code as prefix!
Delete Center NumberCENTER,password,D#Example: CENTER,888888,D#
Data Upload Time IntervalTIMER,T1,T2#Example: TIMER,5,180# (Means the tracker will upload data every 5s when ACC is on and 180s when ACC is off)
T1 ranges 0/5~18000 or 0(seconds), upload interval when ACC ON, 0 means no upload, default is 10;
T2 ranges 0/5~18000 (seconds), upload interval when ACC OFF, default is 10;
Heartbeat Packet UploadHBT,time#Example: HBT,3# (Means the tracker will send heartbeat data package to server every 3 min for connection maintenance)
NOTE: Range :1-60min, default 3min.
Sensor SensitivityLEVEL,A#Example: LEVEL,2# (Means set up the shake sensor level to 2)
NOTE: A: Sensitivity Level 1-9 (1-9 is from weak to strong vibration)
Arm manuallyARM#Set the device into arm mode
Disarm manuallyDISARM#Set the device out of arm mode
Data Upload Time Zone SettingDATAGMT,Time zone orientation,Whole Time Zone[,Half Time Zone]#DATAGMT,E,8# (if no half time zone)
DATAGMT,W,9,30# (if has half time zone)
NOTE: Parameter : E/ W; 0 ~ 12; 0/15/30/45
Set the instruction passwordPWD,password,ON#Enable instruction password successfully!
PWD,password,OFF#Cancel instruction password successfully!
Change the instruction passwordPWDCHG,[A],[B]#A=old password, six digitals, digital range: 0-9, default: 888888;
B=new password, six digitals, digital range: 0-9
Reset passwordRSTPWD,A#A=ID Number, ID number of the device;
Enable BuzzerBUZZER,ON,A#Example: BUZZER,ON,10# (Means the ringing time will last 10s after enabled the buzzer)
A: Ringing duration 0-3600s; Unit: second
Lock DoorLOCKDOOR#Lock door successfully!
Unlock DoorUNLOCKDOOR#Unlock door successfully!
Pulse Times for Unlock DoorPULSE,A#Example: PULSE,1# (Means after sending the command to unlock the car door, user just need pull the door 1 time and the door will open)
A: Pulse frequency 1-5; Unit: times, default: 1
Cut Off / Resume FuelRELAY,A#A=1/2; 1: Enable relay immediately, 2: Enable relay safely
For Example: 1. RELAY,1# (A is set to 1, the relay command will be executed immediately.)
2. RELAY,2# (A is set to 2, the relay command will be executed safely. The vehicle is safe only when the speed is lower than 20km/h if GPS is fixed, or the vehicle is stationary if GPS is not fixed.)
Signal Jamming Cut-off FuelSIGJAMCUT,A,M#Example: SIGJAMCUT,ON,1# (Means the no GNSS signal alarm already been enabled and the alarm message will be sent via Server, SMS and Call)
A=ON/OFF; default:ON
M=1/2; way of alarm, 1 : Cut-off Immediately, 2: Cut-off Safely, Default:2
1. SIGJAMCUT,ON,1# (A is set to 1, the relay command will be executed immediately.)
2. SIGJAMCUT,ON,2# (A is set to 2, the relay command will be executed safely. The vehicle is safe only when the speed is lower than 20km/h if GPS is fixed, or the vehicle is stationary if GPS is not fixed.)
Inquiry sigjamcut function statusSIGJAMCUT#SIGJAMCUT:OFF

Alarm Commands

FunctionsCommand FormatExplanation
Open Door Alarm SettingDOORALM,A,M#Example: DOORALM,ON,1# (Means once the door open the alarm message will be sent out via SMS and server)
A=ON/OFF, default: ON;
M=0/1/2, way of alarming, 0: GPRS only, 1: SMS+GPRS, 2: SMS+GPRS+Call,default:1;
DOORALM,OFF#CANCEL OPEN DOOR ALARM OK
Signal Jamming AlarmSIGJAMALM,A,M#Example: SIGJAMALM,ON,1# (When detected signal jamming the device will alarm via SMS and server)
A=ON/OFF, enable or cancel signal jamming alarm, default: OFF
M=0/1/2, way of alarm, 0 : Server only, 1: SMS+Server, 2: SMS+Server+Call default: 1.
SIGJAMALM,OFF#CANCEL SIGJAMALM OK
SOS AlarmSOSALM,A,M#Example: SOSALM,ON,1# (When press the SOS button more than 3s the device will send SOS alarm via SMS and server)
A=ON/OFF, enable or cancel SOS alarm, default: OFF
M=0/1/2, way of alarm, 0 : Server only, 1: SMS+Server, 2: SMS+Server+Call default: 1.
SOSALM,OFF#CANCEL SOS ALARM OK
Buzzer Alarm SettingBUZZERALM,A,B#Example: BUZZERALM,ON,10# (Means the buzzer will be enabled once the alarms been triggered, and the ringing time will last 10s)
NOTE: B: Ringing duration 0-3600s; Unit: second
Reference alarms: SOS alarm, Vibration alarm, Overspeed alarm, Ignition on alarm, Ignition off alarm, Open door alarm, Signal jamming alarm.
BUZZERALM,OFF#CANCEL SOS ALARM OK
Overspeed Alarm SettingSPEED,A,B,M#Example: SPEED,ON,100,1# (When the speed of the tracker exceeds 100km/h it will send alarm message via SMS and server)
A=ON/OFF, enable or cancel over speed alarm, default: OFF
B=1~255(km/h), speed limit, default: 100(km/h);
M=0/1/2, way of alarm, 0 : Server only, 1: SMS+Server, 2: SMS+Server+Call default: 1.
SPEED,OFF#CANCEL OVERSPEED ALARM OK
Vibration Alarm SettingSENALM,A,M#Example: SENALM,ON,2# (Means enable the vibration alarm, and the alarm message will be sent via SMS, server and call once it is triggered)
A=ON/OFF, default: OFF;
M=0/1/2, way of alarming, 0: Serveronly, 1: SMS+Server, 2: SMS+Server+Call, default:2
SENALM,OFF#CANEL VIBRATE ALARM OK
Shift Alarm SettingSHIFT,A,B,M#Example: SHIFT,ON,300,1# (Means Setting 300 meters shift alarm range, when the ignition turned off, vehicle's 300 meters' shift will trigger the alarm, the alarm message will be sent via SMS and server)
A=ON/OFF; default:ON
B=Shift Distance (Range: 100-9999m)
M=0/1/2; way of alarm, 0 : Server only, 1: SMS+Server, 2: Server+SMS+CALL, default:1
SHIFT,OFF#CANCEL SHIFT ALARM OK
Auto Arm By ACCACCARM,ON,M#Example: ACCARM,ON,60# (Means when the engine turned to off status, the tracker will enter into arm status automatically after 60s)
Arm Time: M=5-1800s, default: 60s
ACCARM,OFF#Close auto arm function
ACC Status Change AlarmACCALM,A,B,M#Example: ACCALM,ON,2,2# (Means enable this alarm type, tracker will send alarm message via SMS, server and call when engine start and flameout)
A=ON/OFF, Default: ON;
B: 0/1/2; 0: ACC ON Alarm; 1: ACC OFF Alarm; 2: ACC ON&OFF Alarm; Default:2
M: 0/1/2 (way of alarm): 0: Server only, 1: SMS+Server, 2: SMS+Server+Call, Default:1;
ACCALM,OFF#Cancel ACC alarm function
Power Disconnect AlarmPWRALM,A,M#Example: PWRALM,ON,1# (Means when the external power disconnect the tracker will send alarm message via SMS and server)
A=ON/OFF, default ON;
M=0/1/2, ways of alarming, 0: Serveronly, 1: SMS+Server, 2: SMS+Server+Call, default:2;
PWRALM,OFF#Close power disconnect alarm
Low Voltage Alarm SettingLVALM,A,B,M#Example: LVALM,ON,11.2V,1# (Means once the external power voltage is less than 11.5v the tracker will send alarm message out via SMS and server)
A=ON/OFF, default: ON;
B=9-95 V, Low voltage threshold, can be a decimal, such as 12.5 V
M=0/1/2, way of alarming, 0: GPRS only, 1: SMS+GPRS, 2: SMS+GPRS+Call, default:1
LVALM,OFF#CANCEL LOW VOLTAGE ALARM OK

Inquiry Commands

FunctionsCommand FormatExplanation
Version InquiryVERSION#ID:19176167105
IMEI:865413059939685
ICCID:89860083192025025636
VERSION:MV750G_EG915_808_V_1_0_20241121
Parameter InquiryPARAM#Device Reply Example:
ID:9301074948
IMEI:861157040411486
APN:CMNET
IP:47.254.77.28:7700
TIMER:10,180
SPEEDLIMIT: 120km/h
ANGLERPT: 30'
CENTER: 13428768257
SOS:13267052361,13488888888,13599999999
GMT:E8.00
Latitude&Longitude InquiryWHERE#LAT:N23.02930,LON:E114.32180,COURSE:0.00,SPEED:0.00KM/H,DATETIME:2015-05-23 14:39:11
Map URL InquiryURL#http://map.google.com/?q=22.557868,113.935090
<0.0km/h 0.0> <2014-12-12 07:32:13>
IMEI:354188047752402
Address InquiryPOSITION#NOTE: Reply message's language is determined by device's language setting, if get position content failed, device will reply Google Map location link.
Status InquirySTATUS#BATTERY: XX% (Built-in Battery Power Percent)
INTERNET: CLOSED (No Network)
FAILED (Connecting Network or Failure)
SUCCESS (Connected to Network)
NET: NONE (No cellular Signal), HIGH / MED / LOW (Signal Strength), 18(Signal value)
GPS: CLOSED (GPS Module Closed);
FIXED,N (Positioned and satellite number);
UNFIX,0 (Not Positioned yet)
SPEED: 30KM/H
ACC: ON / OFF (ACC on or off)
RELAY: ON / OFF (Relay on or off)
POWER: CONNECTED / DISCONNECTED (Power Connected or Disconnected), 12.5V (Vehicle battery voltage)
SENSOR: ON/OFF (Sensor on or off), LEVEL: 3 (Sensitivity level 1-9)
STATE: ARM (Arm or Disarm)
DOOR: Lock (Lock/Unlock)
Alarms ParametersALARM#ID: 19172012644 (ID number of device)
STATE: ARM(DISARM)(Defense status of device)
SPEED: ON/OFF(alarm status); 30km/h(alarm value); alarm way
SHIFT: ON/OFF(alarm status); 300m(alarm value); alarm way
VIBRATE: ON/OFF(alarm status);3(sensitivity level); alarm way
ACC: ON/OFF(alarm status); 0/1/2(0: ACC ON, 1: ACC OFF; 2: ACC ON&OFF) (alarm situation); alarm way;;
POWER DOWN: ON/OFF(alarm status);alarm way
LOW VOLTAGE: ON/OFF(alarm status);alarm way
DOORALM: ON/OFF(alarm status);alarm way
NOTE: Alarm Ways: 0/1/2 ( 0 : SERVER only, 1: SMS+GPRS, 2 : GPRS+SMS+CALL)

Troubleshooting

If you encounter any issues with your MV750G tracker, refer to the table below for common problems and their solutions:

TypeUse
Unable to connect to tracking platformCheck the APN and settings. Check whether the data service of SIM card is enabled. Check the balance of SIM card.
Tracker shows offlineCheck whether external power is still connected. Check if the vehicle entered network blind area. Check the balance of SIM card.
Unable to locateMake sure the top side facing upward without metallic things shielded. Make sure it's not in area with no satellite coverage.
Location driftIn area with poor GNSS signal (tall building around or basement), drifting may happen. Check whether vibration happens around to trigger the accelerator.
No command replyMake sure command format is correct. Vehicle may be in network blind area. Make sure SIM card is well inserted and has SMS service.

User Tips

  • SIM Card Activation: If your device shows as inactive or you are not getting a signal, double-check that your SIM card is properly activated with data, SMS, and call services enabled. Ensure the APN settings are correctly configured as per your SIM card provider's information.
  • Power Connection: Always ensure a stable power connection (12V or higher) to the tracker, especially during initial setup and if the device frequently goes offline.
  • Optimal Placement: For best GPS signal reception, install the tracker with its top side facing the sky and avoid obstructions like metal shields.

Warranty and Support

The MiCODUS MV750G comes with a One Year Warranty from the date of purchase.

For any questions, technical support, or warranty claims, please contact us:

A detailed user manual in PDF format is also available for download: MiCODUS MV750G User Manual (PDF)

Download the MiCODUS APP

Search for "MiCODUS" in the iOS App Store or Google Play Store, or scan the QR codes below to download the official MiCODUS tracking application:

QR code for MiCODUS App download on iOS and Android
Scan for iOS & Android App
QR code for HarmonyOS MiCODUS App download
Scan for HarmonyOS App

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.