FLIPSKY 75100

Contents

Flipsky 75100 Electric Skateboard Speed Controller

User Instruction Manual

1. Introduction

The Flipsky FSESC75100 is a high-performance Electronic Speed Controller (ESC) designed for electric skateboards, scooters, ebikes, and similar applications. It features an aluminum PCB for enhanced heat dissipation and supports various control modes and sensors. This manual provides essential information for the safe and effective use of your FSESC75100.

2. Safety Information

  • Always disconnect the battery before making any connections or disconnections to the ESC.
  • Ensure all connections are secure and properly insulated to prevent short circuits.
  • Operate the ESC within its specified voltage and current limits to avoid damage.
  • Keep the ESC away from water, moisture, and extreme temperatures.
  • Improper use or configuration can lead to serious injury or damage to equipment.

3. Package Contents

Please check the package for the following items:

  • 1x Flipsky FSESC75100 with Aluminum PCB
  • 1x USB Cable
  • Various connection cables/harnesses (e.g., PPM, CAN, UART, HALL sensor cables)
Flipsky FSESC75100 and included accessories
Figure 3.1: FSESC75100 with all included accessories.

4. Setup

4.1. Firmware Warning

It is strongly recommended to keep firmware 5.2 as shipped from the factory. Upgrading to newer firmware versions may damage the ESC.

Phase filtering is NOT available for Flipsky ESC75100 and 75200. If using firmware version 5.3 or above (VESC_TOOL 3.01), you MUST turn off the phase filter function by selecting "false" in VESC_TOOL. Failure to do so will result in ESC damage. Do not restore default parameters when using the wizard interface.

4.2. Wiring Diagram and Connections

Refer to the detailed wiring diagram below for proper connection of your FSESC75100. Ensure all connections are firm and correct before applying power.

Detailed wiring diagram for Flipsky FSESC75100
Figure 4.1: Detailed wiring diagram for FSESC75100.

Important: When unplugging connectors, always press the release tab (if present) or gently wiggle while pulling. Do NOT pull directly on the wires to avoid damaging the connectors or wires.

Connection Points:

  • Motor (3 thick wires): Connect the three motor phase wires to the corresponding outputs on the ESC.
  • Battery (Red/Black thick wires): Connect the red wire to the positive (+) terminal of your battery and the black wire to the negative (-) terminal. Observe polarity carefully.
  • USB Port: For connecting to a computer to configure the ESC using VESC_TOOL.
  • PPM Port: For connecting a PWM receiver (e.g., for remote control).
  • CAN Port: For communication with other VESC-based devices or for dual ESC setups.
  • SWD Port: For debugging and advanced firmware development.
  • COMM Port: General communication port.
  • UART2 Port: Universal Asynchronous Receiver-Transmitter port, commonly used for external modules like Bluetooth or GPS.
  • HALL Port: For connecting Hall effect sensors from your motor for sensored operation.
Top view of Flipsky FSESC75100 showing ports
Figure 4.2: Top view of FSESC75100 showing various communication and sensor ports.
Angled view of Flipsky FSESC75100 showing ports
Figure 4.3: Angled view of FSESC75100 highlighting port labels.

4.3. Initial Configuration

After wiring, connect the ESC to your computer via the USB port and use the VESC_TOOL software for initial motor detection and parameter configuration. Follow the VESC_TOOL wizard carefully, paying close attention to the firmware warnings mentioned above.

5. Operating

The FSESC75100 supports both BLDC square wave mode control and FOC sine wave mode. FOC mode generally offers smoother and quieter operation. The ESC is programmable, allowing you to fine-tune parameters such as current limits, voltage cutoffs, and motor control algorithms through VESC_TOOL.

The ESC also features regenerative braking capacity, which recharges your battery during braking, improving efficiency and range.

Video 5.1: Product overview of the Flipsky FSESC75100.

6. Maintenance

  • Keep the ESC clean and free from dust and debris. Use a soft, dry brush or compressed air for cleaning.
  • Regularly inspect all wiring and connectors for signs of wear, corrosion, or damage. Ensure they are securely fastened.
  • Avoid exposing the ESC to direct sunlight for prolonged periods or to environments with high humidity.
  • Ensure adequate airflow around the ESC, especially during operation, to prevent overheating.

7. Troubleshooting

  • ESC Not Powering On: Check battery connections, ensure correct polarity, and verify battery voltage is within the ESC's operating range.
  • Motor Not Spinning/Erratic Behavior: Re-check motor phase wire connections and Hall sensor connections (if used). Perform motor detection again in VESC_TOOL. Verify remote control signal.
  • ESC Overheating: Ensure proper ventilation and consider reducing current limits if operating in demanding conditions. Check for short circuits in motor windings.
  • Unexpected Shutdowns: Could be due to voltage sag (battery too weak), overcurrent, or overheating. Check VESC_TOOL logs for fault codes.
  • Firmware Issues: If you experience issues after a firmware update, refer to the critical firmware warnings in Section 4.1. Reverting to factory firmware (5.2) might be necessary if problems persist.

For detailed diagnostics, connect the ESC to VESC_TOOL and check the real-time data and fault codes.

8. Specifications

FeatureSpecification
SizeL85mm*W50.7mm*H33.8mm*H18.5mm+5.9mm USB TYPE
Voltage14-84V (4-20S)
Current100A Continuous, 120A Burst
BEC5V@1.5A
Control ModesBLDC Square Wave, FOC Sine Wave
FirmwareLatest (Firmware update supported with caveats)
ERPM150000
Control Interface PortsUSB, CAN, UART
Supported SensorsABI HALL AS5047 AS5048A
Input Set SupportPPM, ADC, NRF, UART
Wire Size12AWG
ProgrammableYes
Regenerative CapacityYes

9. User Tips

  • Check Package Contents: Before starting any installation, verify that all necessary cables and components are included in your package.
  • Double-Check Firmware: Always confirm your ESC's firmware version and adhere to the specific configuration requirements (e.g., phase filter setting) to prevent damage.
  • Secure Connections: Ensure all electrical connections are tight and properly insulated to avoid intermittent issues or short circuits during operation.

10. Warranty and Support

For warranty information and technical support, please refer to the seller or manufacturer's official website. Keep your proof of purchase for any warranty claims.

© 2023 Flipsky. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.