HYULIGHTS HYU-150B

Contents

User Manual: HYULIGHTS HYU-150B LED Par Light

Model: HYU-150B

Brand: HYULIGHTS

1. Introduction

Thank you for choosing the HYULIGHTS HYU-150B LED Par Light. This manual will guide you through the setup, operation, and maintenance of your new professional stage light. Please read these instructions carefully before use and keep this manual for future reference.

Unpacking

Upon unpacking, please verify that the following items are included and undamaged:

  • One Power Cable
  • One user manual
  • One pcs lights
  • One pcs DMX Cable
  • One pcs Infrared remote control

If any items are missing or damaged, please contact your dealer immediately and do not install or operate the device.

Video: Demonstration of the HYULIGHTS LED Par Light's color changing capabilities.

2. Safety Warnings

CAUTION!

Unplug mains lead before opening the housing.

CAUTION! About lithium battery charging and maintenance!

  • Charging environment: Charge at a suitable temperature; avoid high or low temperatures. Extreme temperatures will affect battery performance and life. The lithium battery is normally charged when the power is between 10% and 90%, and can be used after it is fully charged. Can extend battery life!
  • Power retention: When not in use for a long time, keep the battery power between 40%-60%, and check and replenish the power regularly.
  • Storage environment: Store in a dry, cool place, avoid high temperature and humidity.

3. Technical Specifications

FeatureSpecification
Voltage110V~240V, 50-60HZ
Output Power6x18W
LED Type6pcs 18W RGBWA UV 6in1 LED
Wash Angle40 degrees
Color Mixing16.7 million kinds of color change
Channel Modes6/10 Channel
Strobe1 ~ 25 times/second (any color)
Dimmer0-100% smooth dimming
DMX3-pin XLR input/output
Control ModesDMX512/Master-slave/Auto/Sound/WiFi/Wireless Control
Special FunctionRDM remote debugging address code
WIFI Signal ReceptionBarrier-free reception distance 17m (2.4G WIFI)
RC DistanceBarrier-free receiving distance 10m
BatteryBuilt-in Li-ion 8800mAh 11.1V
Charging TimeAbout 3 hours (10 minutes for 40% capacity fast charge)
Waterproof LevelIP44 indoor
MaterialResistant cast aluminum housing
Product Size13.5x13.5x20 cm
Product Weight2.35 kg
Package Size19x18x26cm
Package Weight2.85kg

4. Setup

4.1. DMX-512 Control Connection

Connect the supplied XLR cable to the 3-pin XLR female output of the controller and the other end to the 3-pin XLR male input of the moving head. You can chain multiple moving heads together via a serial link. The required cable should be a two-conductor shielded cable with XLR input and output connectors. Refer to the picture below for connection details.

DMX-512 connection diagram showing DMX Output, DMX Input, and common wiring for 3-pin XLR sockets.
DMX-512 Control Connection Diagram

4.2. Adjusting Light Tilt Angle

Press the bracket under the display to adjust the light tilt angle as needed for your setup.

5. Operation

5.1. LCD Menu Display

The device features an LCD display for easy navigation and control. Use the MENU, UP, DOWN, and ENTER buttons to navigate through the options.

LCD display showing menu options: Dmx512, Shows, Sound, Color, Set, Help.
LCD Menu Interface

LCD Menu Display Function Table

Menu ItemSub-Menu/FunctionDescription
Dmx512 (A001)Auto Color JumpPress ENTER to adjust speed (1-99)
Auto Fade Color GradientPress ENTER to adjust speed (1-99)
Auto Sudden Color MutationPress ENTER to adjust speed (1-99)
ShowsSound Mode 1Press ENTER to adjust sensitivity (1-100)
Sound Mode 2Press ENTER to adjust sensitivity (1-100)
Sound Mode 3Press ENTER to adjust sensitivity (1-100)
ColorCustom Color Manual DimmingR/G/B/W/Y/U: 0-255
Static Color32 static colors to choose
SetDMX Channel6CH/10CH
2.4G Wireless WIFION/OFF
HelpName6 Color (Version V5.2)
Auto Strobe Full-brightAdjust speed (1-99)
Sound Mode 4Adjust sensitivity (1-100)
Display BacklightBrightness0-100%
LCD Close TimeSet backlight off timeOpen, 5S, 10S, 15S, 30S
Fan SpeedAdjust fan speedAuto, Slow, Middle, Fast (Note: This product has no built-in fan, spare)
Restore FactoryCode8888
MANUAL LED BrightnessAdjustment Code6666
TemperatureON/OFF
Battery Level DisplayON/OFF
Background ColorLCD Background color selection
BUZZERON/OFF

5.2. Infrared Remote Control Function

The included infrared remote control allows for convenient operation of the light. Below are the functions of each button:

Infrared remote control with labeled buttons for various light functions.
Infrared Remote Control Layout
  1. UP: Increase value/speed.
  2. DOWN: Decrease value/speed.
  3. OFF: Turn off the light.
  4. ON: Turn on the light.
  5. R, G, B, W, A, UV: Select individual colors (Red, Green, Blue, White, Amber, UV).
  6. Number Keys (1-9): Select from 9 static mixed colors (AC 1...AC 9).
  7. 0 Key (A001 DMX512 mode): Enter DMX512 mode. Use UP/DOWN keys to adjust the address code.
  8. AUTO Color mode: Use UP/DOWN to adjust speed.
  9. STROBE mode: Button strobe switch 32 Strobe Effect. Use UP/DOWN keys to adjust speed.
  10. FADE keys (Color Gradient Mode): Use UP/DOWN keys to adjust speed.
  11. SOUND mode: Use UP/DOWN keys to adjust SOUND mode.

5.3. 2.4G Wireless WIFI Phone APP Control

The light can be controlled wirelessly via a smartphone app. Follow these steps to set up and use the app:

  1. Download the APP: Scan the QR code (not pictured, refer to original manual page 8) or search for "LED LAMP" in your mobile app store to download the application.
  2. Smartphone screen showing the LED LAMP app icon.
    LED LAMP App Icon
    Smartphone screen showing WLAN settings with 'LED_090' connected.
    WLAN Connection to Light's WiFi
    Smartphone screen showing the LED LAMP app interface with a color wheel for light control.
    LED LAMP App Color Control Interface
  3. Connect to WIFI: In the light's menu, navigate to the "SHOWS" menu. The WiFi icon will display "LED-XXX", where XXX represents the light's address. Use your mobile phone's WLAN settings to find and connect to the corresponding "LED-XXX" WiFi network.
  4. LCD display showing WIFI MODE menu with LED-XXX identifier.
    WIFI Mode Display on LCD
  5. Open the LED LAMP APP: After successful WiFi connection, open the LED LAMP app. The "LED LIGHT" interface should automatically pop up. Click on the "LED LIGHT" program to control the light.

APP Control Notes:

  • Menu HELP: Press the ENTER key in the "HELP" menu to display the information query bar. Use UP and DOWN keys to navigate.
  • App Connection Issue: If the HOME interface does not display the LED LIGHT program after about 1 minute, exit and reopen the APP.
  • A001 Mode (Pixel Refresh Rate): Press and hold the MENU key for about 5 seconds to adjust the pixel refresh rate (1200KHZ/4000KHZ/12KHZ/20KHZ). Press MENU to exit.
  • A001 Mode (Brightness Mixing Value): Press and hold the ENTER key for about 5 seconds to adjust the brightness mixing value (0-20). Press ENTER to exit.
  • Charging Display: During battery charging, the display will show a charging interface. To use the lamp while charging, press the MENU key to enter the main operation interface.
  • Additional Features: The device includes remote control operation prompt sound, temperature protection function, and wired RDM function.
  • Temperature Protection: If the temperature exceeds 65 degrees, the program will automatically reduce power to 30%. If the temperature exceeds 95 degrees, the light will automatically turn off.

5.4. DMX Channels

The light supports DMX512 control with either 6 or 10 channel modes. The following table details the functions of each channel:

Numeric6 DMX Channel10 DMX Channel
CH11-255 Red Dimming1-255 Total Dimming
CH21-255 Green Dimming1-255 Red Dimming
CH31-255 Blue Dimming1-255 Green Dimming
CH41-255 White Dimming1-255 Blue Dimming
CH51-255 Yellow Dimming1-255 White Dimming
CH61-255 UV Dimming1-255 Yellow Dimming
CH71-255 UV Dimming
CH81-255 Strobe
CH90-8 off light
9-50 Static color mixing mode (32 colors)
51-100 Jump Mode
101-150 Mutation Mode
151-200 Gradient Mode
201-220 Sound 1
221-240 Sound 2
241-255 Sound 3
CH101-255 Speed and color selection (9CH and 10CH Cooperate)

5.5. Wireless Transceiver Pairing (Master-slave mode)

For master-slave operation, both the master and slave lights must be set to the same channel/color. The LED indicator provides status feedback:

  • Constantly lit LED: No DMX/wireless signal.
  • Red LED flashing: Successful transmission.
  • Green LED flashing: Successful reception.

The faster the DMX data transmission speed, the faster the LED indicator lights up and the communication is established.

RF Frequency and Channel Settings:

  • RF Frequency: 2.400-2.525GHz, with 126 frequency bands automatically selected.
  • Channel Settings: Use the "WIRELESS DMX CODE" button to switch channels/colors. 7 channels/colors are available with the following ID codes and LED color correspondences:
    1. Red = Red
    2. Green = Green
    3. Red + Green = Yellow
    4. Blue = Blue
    5. Red + Blue = Purple
    6. Green + Blue = Orange
    7. Red + Green + Blue = White
Rear view of the light showing wireless channel indicator, wireless channel key, display screen, MIC, infrared receiver, and operation keys.
Wireless Control Interface

6. Maintenance

To ensure the longevity and optimal performance of your HYULIGHTS LED Par Light, follow these maintenance guidelines:

  • Cleaning: Regularly clean the lenses and exterior of the light with a soft, lint-free cloth. Avoid using abrasive cleaners or solvents.
  • Battery Care: Adhere to the battery charging and storage guidelines mentioned in the Safety Warnings section to maximize battery life.
  • Inspection: Periodically check all cables and connections for any signs of wear or damage. Replace any faulty components immediately.
  • Storage: When not in use, store the light in a dry, cool place, away from direct sunlight and extreme temperatures.

7. Troubleshooting

This section addresses common issues you might encounter with your LED Par Light. If you experience a problem not listed here, please contact customer support.

  • Light not turning on:
    • Check if the power cable is securely connected.
    • Ensure the battery is charged.
    • Verify the power switch is in the ON position.
  • No DMX signal:
    • Check DMX cable connections.
    • Ensure the DMX controller is functioning correctly.
    • Verify the light is in DMX512 mode (A001).
  • APP control not connecting:
    • Ensure the light's WiFi is ON and you are connected to the correct "LED-XXX" network on your phone.
    • Restart the "LED LAMP" app if the interface does not appear after connection.
  • Light overheating:
    • Ensure adequate ventilation around the unit.
    • The light has built-in temperature protection and will reduce power or shut off if it gets too hot. Allow it to cool down.

8. User Tips

No specific user tips were available from provided reviews or Q&A. For best performance, ensure the light is placed on a stable surface and operated within its specified temperature range.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your original point of purchase or the manufacturer directly. Keep your purchase receipt as proof of purchase.

For additional resources, you may refer to the official user manual PDF: View User Manual (PDF)


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.