1. Introduction
The DAKEFPV F722 Flight Control FC and 4-in-1 ESC stack is a high-performance electronic system designed for FPV racing drones. It integrates an advanced F722 flight controller with a powerful 4-in-1 Electronic Speed Controller (ESC), offering robust control and power delivery for demanding flight applications. This manual provides essential information for the proper installation, configuration, and operation of your DAKEFPV F722 stack.
Key Features:
- F722 Main Control Chip (STM32H743)
- ICM42688P Gyroscope for precise flight control
- Supports 3-12S LiPo input voltage
- Available with 100A or 120A 4-in-1 ESC options
- 30.5x30.5mm mounting pattern
- Built-in Barometer and 16MB Black Box Flash
- Direct plug-in support for DJI Air Units (O3/RunCam Link/Caddx Vista/V1)
- Supports up to 8 motors and 4 servos
- Integrated 5V 3A and 12V 3A dual independent BECs
2. Package Contents
The contents of your package may vary depending on the specific option purchased. Please verify against the list below:
Option 1: DAKEFPV F722 120A 30x30 STACK

Image: Contents of the DAKEFPV F722 120A 30x30 STACK package, showing the flight controller, 4-in-1 ESC, capacitor, nuts, grommets, cables, and screws.
- DAKEFPV F722 Flight Controller x 1
- DAKEFPV BLS 120A 4 in 1 ESC x 1
- 35V 1000uF Low ESR Capacitor x 1
- M3 Nylon Nut x 5
- M3 Silicone O Ring x 5
- M3*8mm Silicone Grommets (for FC) x 1
- M3*8.1mm Silicone Grommets (for ESC) x 1
- SH 1.0mm 25mm-length 8pin Cable (for FC-ESC connection) x 1
- SH 1.0mm 75mm-length 8pin Cable* x 1
- M3*30mm Inner-hexagon Screws x 5
- GPS 6pin cable, Analog VTX 6pin cable, dual-camera 6pin cable x 1
- XT60 Power Cable (70mm) x 1
*Note: When the ESC tail faces the drone's front, use the 75mm-length 8pin cable for the flight controller and ESC; both ends plug interchangeably.
Option 2: DAKEFPV F722 120A 30x30 FC (Flight Controller Only)

Image: Contents of the DAKEFPV F722 120A 30x30 FC package, showing the flight controller, various grommets, screws, nuts, and connection cables.
- DAKEFPV F722 Flight Controller x 1
- Silicone Grommets (random colors) x 8, hexagon screws x 5, hexagon nuts x 5, silicone rings x 3
- FC12-pin to ESC 8-pin cable, LED/buzzer 4-pin cable x 1
- GPS 6-pin cable, analog VTX 6-pin cable, dual-camera 6-pin cable x 1, receiver 4-pin cable
Option 3: DAKEFPV 12S 120A 4 in 1 ESC (ESC Only)

Image: Contents of the DAKEFPV 12S 120A 4 in 1 ESC package, showing the ESC, capacitors, FC-ESC cable, and XT60 connector.
- DAKEFPV 12S 120A 4 in 1 ESC x 1
- 35V 1000uF Low ESR Capacitor (Note: 12S ESC includes 63V1000uF Capacitor)
- FC 12-pin to ESC 8-pin cable (for connecting FC to ESC)
- XT60 x 1
3. Specifications

Image: Detailed specifications table for both the F722 Flight Controller and the 4-in-1 ESC.
| Feature | DAKE F722 Flight Controller | DAKE 12S 120A 4 in 1 ESC |
|---|---|---|
| Main Control Chip | STM32H743 | N/A |
| Gyroscope | ICM42688P | N/A |
| USB Interface Type | Type-C | N/A |
| Barometer | Built-in | N/A |
| OSD Chip | AT7456E | N/A |
| Bluetooth BLE | None | N/A |
| WIFI | Not supported | N/A |
| DJI Air Unit Connection | Supports 6pin plug direct connection, two wiring methods. Fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1. | N/A |
| FLASH Memory | 16MB | N/A |
| Ammeter | Supported | Supported (Scale=400, Offset=0) |
| Input Voltage | 3-8S LiPo | 3-8S LiPo |
| UART Ports | 8 groups | N/A |
| Buzzer Pad | Supports BZ+, BZ- buzzer access 5V | N/A |
| BOOT Button | Press simultaneously with power on to enter DFU mode for firmware flashing. | N/A |
| RSSI Pad | Supported (top right pad) | N/A |
| SmartPort / F.Port | Not supported | N/A |
| Supported Firmware | BetaFlight (default), ArduPilot | BLHeli_S / BlueJay |
| Firmware Target Name | DAKEFPVF722 | N/A |
| Mounting Holes | 30.5 x 30.5 mm (4mm holes) | 30.5 x 30.5 mm (4mm holes) |
| Dimensions (FC) | 36 x 36 x 8 mm | N/A |
| Dimensions (ESC) | N/A | 45.4 x 42.8 x 6.5 mm |
| Weight (FC) | 10.5g | N/A |
| Weight (ESC) | N/A | 23.5g |
| Continuous Current | N/A | 120A x 4 |
| Max Current | N/A | 125A x 4 - 10S |
| TVS Diode | N/A | Built-in TVS transient suppression diode |
| External Capacitor | N/A | 1000uF low resistance capacitor (included) |
| ESC Protocol | N/A | Dshot300/Dshot600/PWM/Bi-directional Dshot |
| Output Voltage | N/A | VBAT |
| Temperature Sensor | N/A | Not supported |
Physical Dimensions

Image: Diagram showing the dimensions of the F722 Flight Controller and the 4-in-1 ESC, including mounting hole spacing and overall stack height.
4. Setup
4.1 General Installation Notes

Image: Text highlighting critical installation considerations for the flight controller and ESC stack.
When installing your stack, adhere to the standard mounting method. The orientation of the gyroscope and motor sequence can be adjusted through settings. If you opt for an inverted manner, be extra careful about the space between the frame, the FC, and the ESC.
It is critical to swap the silicon pads when changing the positions of the FC and the ESC, as illustrated in the product images. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Please be aware that any damage resulting from improper installation of this nature is not covered under the warranty.
4.2 Wiring Diagrams
Careful wiring is crucial for the proper function and longevity of your FPV system. Refer to the diagrams below for correct connections.

Image: Comprehensive wiring diagram for the DAKEFPV F722 Flight Controller, showing connections for motors, receiver, VTX, camera, GPS, LED, and USB.

Image: Diagram illustrating the connection between the Flight Controller and the motors, as well as the overall stack assembly.
4.2.1 DJI Air Unit Connections
The DAKEFPV F722 Flight Controller supports direct plug-in for various DJI Air Units.

Image: Diagram showing how to connect the DAKEFPV F722 Flight Controller to a DJI O3 Air Unit using the provided 6-pin cable.
For DJI O3 Air Unit, use the 6-pin cable that comes with the O3 Air Unit.

Image: Diagram showing how to connect the DAKEFPV F722 Flight Controller to a RunCam Link or Caddx Vista Air Unit using the 6-pin cable from accessory No.11 in the package section.
For RunCam Link/Caddx Vista Air Unit, use the 6-pin cable that comes with the H743 stack (refer to accessory No.11 in the package section).
4.2.2 SBUS Receiver Connection

Image: Diagram and text explaining the importance of disconnecting the SBUS signal wire when using an ELRS receiver with a DJI Air Unit.
When using an SBUS receiver, the SBUS signal wire of the receiver must be connected to the SBUS pad on the front side of the flight controller (this pad internally uses UART2).
If you are also using the DJI Air Unit (O3/Link/Vista/Air Unit V1) simultaneously, some ELRS receivers may not be recognized properly by the flight controller. If you encounter this issue, you need to disconnect the SBUS signal wire from the Air Unit harness. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.
DO NOT connect this wire to assure the external SBUS receiver works properly!
For some ELRS receivers, it is necessary to disconnect this wire in order to function properly!
4.3 Software Configuration
The DAKEFPV F722 Flight Controller comes pre-flashed with BetaFlight firmware. It also supports ArduPilot. The ESC uses BLHeli_S / BlueJay firmware.
- Flight Controller Firmware: Connect the FC to your computer via the Type-C USB port. Use the BetaFlight Configurator (or ArduPilot Mission Planner) to configure settings, calibrate sensors, and update firmware. The default firmware target name is DAKEF PVF722.
- ESC Firmware: Use the BLHeliSuite or BlueJay Configurator to update or configure your ESC settings.
5. Operating Instructions
5.1 Battery Capacity Indicator

Image: Diagram showing the 4-level battery capacity indicator LEDs on the flight controller.
The flight controller features a 4-level battery capacity indicator. As soon as you connect the battery, you can instantly see the battery level, eliminating the need for an external LiPo checker.
- X1: FCC
- X2: 3V
- X3: 5V
- X4: 12V
5.2 LED Light Bar Pads

Image: Diagram showing the LED pads on the flight controller and an example of an LED strip connected.
The LED pads at the corners of the flight controller allow you to connect and control LED light strips. A single press of the BOOT button lets you switch between different lighting modes. A long press of the BOOT button switches to the onboard LED light effect control mode, and short presses toggle between various preset light effects.
5.3 Black Box Functionality

Image: Close-up of the flight controller highlighting the 16MB FLASH memory chip.
The built-in 16MB large memory FLASH continuously records flight status data (sensor data, control commands, fault codes). In the event of a crash or power outage, this data can still be retrieved for accident analysis and tuning.
5.4 Motor Support

Image: Diagram of the flight controller highlighting the M1-M8 motor outputs.
The flight controller supports up to 8 motors (M1-M8), making it suitable for X8, Y6, fixed-wing, and other aircraft models that require more than 4 motors. It also supports 4 servos.
6. Maintenance
To ensure the longevity and optimal performance of your DAKEFPV F722 stack, follow these maintenance guidelines:
- Prevent Voltage Spikes: It is strongly recommended to use the Low ESR capacitor included in the package to prevent the stack from being burnt out by voltage spikes on powering up.
- Regular Inspection: Periodically check all solder joints and connections for any signs of damage, corrosion, or loose wires.
- Cleanliness: Keep the flight controller and ESC free from dust, dirt, and moisture. Use compressed air or a soft brush for cleaning.
- Firmware Updates: Regularly check for and apply the latest firmware updates for both the FC (BetaFlight/ArduPilot) and ESC (BLHeli_S/BlueJay) to benefit from performance improvements and bug fixes.
- Proper Handling: Always handle the boards by their edges to avoid touching sensitive components, especially the gyroscope.
7. Troubleshooting
- Stack Not Powering On: Double-check all power connections, especially the XT60 and battery leads. Ensure the battery is charged and the voltage is within the supported 3-12S range.
- SBUS Receiver Not Recognized: If using an ELRS receiver with a DJI Air Unit, ensure the SBUS signal wire from the Air Unit harness is disconnected and insulated. Connect the receiver's SBUS signal wire directly to the FC's SBUS pad.
- Flight Controller Not Connecting to PC: Ensure you have the correct USB drivers installed. Try a different USB cable and port. If the FC is unresponsive, try entering DFU mode by holding the BOOT button while connecting to USB, then use BetaFlight Configurator to flash firmware.
- Motors Not Spinning/Incorrectly: Verify motor wiring and ESC calibration. Check motor direction in BetaFlight/ArduPilot. Ensure ESC firmware is up to date.
- Unstable Flight: Check for proper sensor calibration (accelerometer, gyroscope). Ensure the FC is soft-mounted correctly to reduce vibrations. Review PID tuning settings.
- Damage from Voltage Spikes: If the stack was powered without the recommended Low ESR capacitor, internal components may be damaged. This type of damage is typically not covered under warranty.
8. User Tips
- Firmware Target: When flashing BetaFlight, ensure you select the correct firmware target, which is DAKEF PVF722 for this flight controller.
- ESC Software: The ESC uses BLHeli_S or BlueJay firmware. You can use the respective configurators for updates and settings.
- Wiring Best Practices: Always double-check your wiring against the provided diagrams before applying power. Insulate any exposed wires or solder joints to prevent short circuits.
- Capacitor Installation: Do not skip installing the included Low ESR capacitor. It is vital for protecting your ESC and FC from damaging voltage spikes.
9. Warranty & Support
DAKEFPV products are manufactured to high standards. This product is covered by a manufacturer's warranty against defects in materials and workmanship under normal use. Please refer to the seller's terms and conditions for specific warranty duration and claim procedures.
Damage caused by improper installation, misuse, unauthorized modifications, or accidents is not covered under warranty. This includes, but is not limited to, damage from voltage spikes due to not installing the recommended capacitor, or short circuits from incorrect wiring.
For technical support or inquiries, please contact your retailer or the DAKEFPV customer service directly.