DAKEFPV F405 V3 FC Stack

Contents

DAKEFPV F405 V3 Flight Controller and ESC Stack Instruction Manual

Model: F405 V3 FC Stack

For FPV Freestyle Drones

1. Introduction and Overview

The DAKEFPV F405 V3 Flight Controller and ESC Stack is a high-performance solution designed for FPV freestyle drones. It features a powerful STM32F405 MCU, an ICM42688P gyroscope, and a robust 12S 100A/120A 4-in-1 ESC. This stack supports popular flight control firmware such as Betaflight, Ardupilot, and INAV, offering versatility and advanced capabilities for drone enthusiasts. Key features include a built-in barometer, 16MB black box flash memory, dual BEC outputs, and direct plug-in compatibility with DJI Air Units.

DAKEFPV F405 V3 Flight Controller with STM32F405 MCU and pinout diagram
Figure 1.1: DAKEFPV F405 V3 Flight Controller with STM32F405 MCU and pinout diagram.
DAKE F405 BLS 120A Stack features summary
Figure 1.2: Summary of DAKE F405 BLS 120A Stack features, including BetaFlight/ArduPilot support, 120A ESC, dual gyroscopes, analog switches, dual cameras, 5V/12V BEC, 16M FLASH, external GPS support, 1000uF capacitor, DJI Air Unit direct plug-in, and built-in barometer.

2. Package Contents

Please verify that all components are present in your package based on the option purchased:

Option 1 - DAKEFPV F405 120A 30x30 STACK

  • DAKEFPV F405 Flight Controller x 1
  • DAKEFPV BLS 120A 4 in 1 ESC x 1
  • 35V 1000uF Low ESR Capacitor x 1
  • M3 Nylon Nut x 5
  • M3 Silicone O-Ring x 5
  • M3*8mm Silicone Grommets (for FC) x 1
  • M3*8.1mm Silicone Grommets (for ESC) x 1
  • SH 1.0mm 25mm-length 8pin Cable (for FC-ESC connection) x 1
  • SH 1.0mm 75mm-length 8pin Cable x 1
  • M3*30mm Inner-hexagon Screws x 5
  • GPS 6pin cable, Analog VTX 6pin cable, dual-camera 6pin cable x 1
  • XT60 Power Cable (70mm) x 1

Option 2 - DAKEFPV F405 30x30 FC

  • DAKEFPV F405 Flight Controller x 1
  • Silicone Grommets (random colors) x 8
  • Hexagon nuts x 5
  • Silicone rings x 5
  • FC 12-pin to ESC 8-pin cable, LED/buzzer 4-pin cable x 1
  • GPS 6-pin cable, analog VTX 6-pin cable, dual-camera 6-pin cable x 1, receiver 4-pin cable

Option 3 - DAKEFPV 12S 120A 4 in ESC

  • DAKEFPV 12S 120A 4 in ESC x 1
  • 35V 1000uF Low ESR Capacitor (63V1000uF Capacitor for 12S ESC)
  • FC 12-pin to ESC 8-pin cable (for connecting FC to ESC)
  • XT60 x 1
Package contents for DAKEFPV F405 120A 30x30 STACK
Figure 2.1: Package contents for Option 1 - DAKEFPV F405 120A 30x30 STACK.
Package contents for DAKEFPV F405 30x30 FC and 12S 120A 4 in ESC
Figure 2.2: Package contents for Option 2 (DAKEFPV F405 30x30 FC) and Option 3 (DAKEFPV 12S 120A 4 in ESC).

3. Specifications

Flight Controller (F405)

FeatureSpecification
Main Control Unit (MCU)STM32F405
GyroscopeICM42688P
USB InterfaceType-C
BarometerBuilt-in
OSD ChipAT7456E
Bluetooth BLENo
WIFINot supported
DJI Air Unit ConnectionSupports 6-pin plug-in, two wiring methods. Fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1.
FLASH (Black Box)16MB
Current MeterSupported
Input Voltage3-8S LiPo
Mounting Hole30.5 x 30.5 mm (4mm hole diameter)
Dimensions36 x 36 x 8 mm
Weight10.5g
Supported FirmwareBetaFlight (default), Ardupilot, INAV
Firmware Target NameDAKEFPVF405

Electronic Speed Controller (BLS 120A 4-in-1 ESC)

FeatureSpecification
Product NameDAKE 12S 120A 4 in 1 ESC
FirmwareBLHeli_s/BLUEJay
Input Voltage3-12S LiPo
Continuous Current120A x 4
Maximum Current125A x 4 (for 10 seconds)
Built-in TVS DiodeYes
External Capacitor1000uF (included)
ESC/Motor ProtocolDshot300/Dshot600/PWM/Bi-directional Dshot
Output VoltageVBAT
Current MeterSupported (Scale=400, Offset=0)
TelemetryNot supported
Mounting Hole30.5 x 30.5 mm (4mm hole diameter)
Dimensions45.4 x 42.8 x 6.5 mm
Weight23.5g
Dimensions diagram for DAKEFPV F405 Flight Controller and ESC
Figure 3.1: Dimensions of the F405 Flight Controller and the 4-in-1 ESC.

4. Setup and Installation

4.1 Mounting the Stack

When installing your stack, adhere to the standard mounting method. The orientation of the gyroscope and motor sequence can be adjusted through software settings. If you opt for an inverted mounting, be extra careful about the space between the frame, the Flight Controller (FC), and the Electronic Speed Controller (ESC).

It is critical to swap the silicon pads when changing the positions of the FC and the ESC. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Any damage resulting from improper installation of this nature is not covered under warranty.

Important Stack Installation Note and cable connection diagrams
Figure 4.1: Important installation notes and cable connection examples.

4.2 Wiring Diagram

Refer to the detailed wiring diagram below for connecting your flight controller and ESC to other components such as motors, receivers, VTX, GPS, and cameras. Both the FC and ESC can be connected via direct soldering or using the provided cables.

Detailed wiring diagram for DAKEFPV F405 FC and ESC stack
Figure 4.2: Comprehensive wiring diagram for the F405 FC and ESC stack, showing connections for motors, cameras, GPS, LED, and receivers.
F405 Flight Controller layout and pinout
Figure 4.3: F405 Flight Controller layout showing pin assignments for various peripherals.

4.3 Capacitor Installation

To prevent the stack from being damaged by voltage spikes during power-up, it is strongly recommended to install the Low ESR capacitor included in the package. Solder it to the main battery pads (BAT+ and BAT-) on the ESC.

TVS diode and capacitor installation details
Figure 4.4: Illustration of TVS diode, filter capacitors, and the recommended 1000uF Low ESR capacitor for smooth power delivery.

4.4 DJI Air Unit Connection

The DAKEFPV F405 FC is fully compatible with DJI O3, RunCam Link, Caddx Vista, and DJI Air Unit V1. Use the provided 6-pin cable for direct plug-in connection. No wiring changes are needed for these units.

Cable connection for DJI Air Unit V1
Figure 4.5: Cable connection example for DJI Air Unit V1.

4.5 SBUS Receiver Connection

When using an SBUS receiver, the SBUS signal wire of the receiver must be connected to the dedicated SBUS pad on the front side of the flight controller (this pad internally uses UART2).

Important Notice: If you are also using the DJI Air Unit (O3/Link/Vista/Air Unit V1), you will need to disconnect the SBUS signal wire from the Air Unit harness. Failure to do so will prevent the SBUS receiver from being properly recognized by the flight controller. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector or directly cut this wire and insulate the exposed part of the wire carefully.

4.6 ELRS Receiver Connection

We recommend connecting the ELRS receiver's TX and RX to the T2 and R2 pads on the flight controller. However, when using the DJI Air Unit simultaneously, some ELRS receivers may not be recognized properly by the flight controller. If you encounter this issue, you need to disconnect the SBUS signal wire from the Air Unit harness (as described in section 4.5).

ELRS receiver connection diagram
Figure 4.6: ELRS receiver connection diagram, showing TX/RX to T2/R2 pads.

4.7 LED Light Bar Pads

The LED pads at the corners of the flight controller allow you to connect and decorate your aircraft with your favorite LED light strips. A single short press of the BOOT button lets you switch between different lighting modes. A long press of the BOOT button switches to the onboard LED light effect control mode.

LED light bar pads connection on F405 FC
Figure 4.7: Location of LED light bar pads on the F405 Flight Controller.

5. Operating Instructions

5.1 Firmware Configuration

The DAKEFPV F405 V3 FC comes pre-flashed with Betaflight firmware. It also supports Ardupilot and INAV. You can connect the flight controller to your computer via the Type-C USB port and use the respective configurator software (Betaflight Configurator, Mission Planner for Ardupilot, or INAV Configurator) to adjust parameters, calibrate sensors, and flash different firmware versions.

5.2 Battery Capacity Indicator

The flight controller features a convenient 4-level battery capacity indicator. As soon as you connect the battery, you can instantly see the battery level, eliminating the need for an external LiPo checker.

F405 Flight Controller with 4-level battery capacity indicator
Figure 5.1: Location and function of the 4-level battery capacity indicator on the F405 FC.

5.3 Black Box Functionality

The built-in 16MB large memory FLASH continuously records flight status data, including sensor readings, control commands, and fault codes. This data can be retrieved for accident analysis in the event of a crash or power outage, aiding in diagnostics and improving flight performance.

F405 Flight Controller with 16MB black box flash memory
Figure 5.2: Illustration highlighting the 16MB black box flash memory on the F405 FC.

5.4 Motor Support

The flight controller supports up to 8 motors, making it suitable for X8, Y6, fixed-wing, and other aircraft models that require more than 4 motors.

F405 Flight Controller supporting up to 6 motors (M1-M6)
Figure 5.3: F405 Flight Controller showing motor outputs M1-M6, indicating support for various multirotor configurations.

6. Maintenance

  • Regular Inspection: Periodically check all solder joints and cable connections for any signs of wear, corrosion, or damage.
  • Cleaning: Keep the flight controller and ESC free from dust, dirt, and moisture. Use compressed air or a soft brush for cleaning. Avoid using liquids directly on the electronics.
  • Firmware Updates: Regularly check for and apply the latest firmware updates for Betaflight, Ardupilot, or INAV to ensure optimal performance and access to new features.
  • Physical Protection: Ensure the stack is adequately protected from physical impacts and vibrations within your drone frame.

7. Troubleshooting

  • No Power/Intermittent Power:
    • Check all power connections, especially the XT60 and capacitor soldering.
    • Ensure the battery is fully charged and healthy.
    • Inspect for any short circuits, particularly between the FC's USB port and the ESC if pads were swapped during inverted mounting.
  • Receiver Not Detected (SBUS/ELRS):
    • Verify the SBUS signal wire is connected to the correct SBUS pad on the FC.
    • If using a DJI Air Unit, ensure the SBUS signal wire from the Air Unit harness is disconnected as per section 4.5.
    • For ELRS, confirm TX/RX are connected to T2/R2 pads.
    • Check receiver binding and power supply.
  • Motors Not Spinning/Incorrectly:
    • Verify motor wiring to the ESC.
    • Check motor direction in your flight control software (Betaflight, Ardupilot, INAV).
    • Ensure ESC calibration is correct.
    • Confirm ESC protocol (Dshot, PWM) is correctly configured in the flight controller software.
  • Unstable Flight:
    • Check for proper mounting and vibration isolation of the FC.
    • Ensure gyroscope calibration is performed correctly.
    • Review PID tuning settings in your flight control software.
    • Check for any loose components or damaged propellers.

8. User Tips

  • Initial Setup: Always perform a dry run with minimal power and propellers removed during initial setup and testing to prevent accidental motor spin-ups.
  • Solder Quality: Ensure all solder joints are clean, shiny, and strong. Cold solder joints are a common cause of intermittent issues.
  • Cable Management: Route cables neatly and secure them to prevent interference with propellers or other moving parts, and to reduce vibration.
  • Firmware Backup: Before making significant changes or updating firmware, always back up your current configuration settings.

9. Warranty and Support

DAKEFPV products are designed for high performance and reliability. Please note that any damage resulting from improper installation, such as short circuits caused by incorrect silicon pad placement during inverted mounting, is not covered under warranty.

For technical support, troubleshooting assistance, or warranty inquiries, please contact the DAKEFPV Store directly through the platform where you purchased the product. Provide your order number and a detailed description of the issue to facilitate a quicker resolution.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.