JASIC NB-250 (N214II)

Contents

JASIC NB-250 (N214II) MIG/MMA All-in-One Welding Machine User Manual

Model: NB-250 (N214II)

1. Introduction

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your JASIC NB-250 (N214II) MIG/MMA All-in-One Welding Machine. Please read this manual thoroughly before using the equipment.

Front view of the JASIC NB-250 (N214II) welding machine, showing the control panel with digital display and adjustment knobs.

Figure 1: Front view of the JASIC NB-250 (N214II) Welding Machine.

2. Safety Information

Always prioritize safety when operating welding equipment. Failure to follow safety precautions can result in serious injury or death.

  • Wear appropriate personal protective equipment (PPE), including welding helmet, gloves, and protective clothing.
  • Ensure proper ventilation to avoid inhaling welding fumes.
  • Keep a fire extinguisher nearby.
  • Do not operate the machine in wet conditions.
  • Ensure all electrical connections are secure and properly grounded.
  • Disconnect power before performing any maintenance or adjustments.

3. Product Overview

The JASIC NB-250 (N214II) is a versatile all-in-one welding machine capable of performing both MIG (Metal Inert Gas) and MMA (Manual Metal Arc) welding. It features a user-friendly control panel for precise adjustments.

JASIC NB-250 (N214II) welding machine shown with included accessories such as a gas regulator, hoses, and welding cables.

Figure 2: Welding Machine with included accessories.

Video 1: Overview of the welding machine production facility, showcasing quality assurance and customization options.

4. Setup

4.1 Unpacking and Inspection

  • Carefully remove the welding machine and all accessories from the packaging.
  • Inspect the machine for any signs of damage during transit. If damage is found, contact your supplier immediately.
  • Ensure all components listed in the packing list are present.
The product packaging box for the JASIC welding machine.

Figure 3: Product packaging.

4.2 Power Connection

  • Connect the machine to a 220V power supply. Ensure the power outlet is properly grounded and can handle the machine's power requirements.

4.3 Gas Connection (for MIG Welding)

  • Connect the gas hose from your shielding gas cylinder (e.g., Argon, CO2, or a mix) to the gas inlet on the rear of the welding machine.
  • Attach the gas regulator to the cylinder and ensure a tight seal.
  • Adjust the gas flow rate according to your welding requirements.

4.4 Wire Feed Installation (for MIG Welding)

  • Open the side panel of the machine to access the wire feed mechanism.
  • Mount the welding wire spool onto the spindle, ensuring it rotates freely.
  • Thread the welding wire through the wire feed rollers and into the MIG torch liner.
  • Adjust the tension of the wire feed rollers to prevent slipping or crushing the wire.
Inside view of the JASIC welding machine, showing the wire feed mechanism with a spool of welding wire installed.

Figure 4: Internal wire feed mechanism.

4.5 Torch and Ground Clamp Connection

  • Connect the MIG torch to the appropriate connector on the front panel.
  • Connect the ground clamp cable to the ground terminal and attach the clamp securely to the workpiece.
  • For MMA welding, connect the electrode holder cable and ground clamp cable to their respective terminals.

5. Operating Instructions

5.1 Control Panel Overview

The control panel features a digital display and various knobs and buttons for selecting welding modes and adjusting parameters.

  • Digital Display: Shows current and voltage settings (e.g., 200A, 26.0V).
  • Mode Selection: Buttons for MIG, MMA, and Pulse welding modes.
  • Adjustment Knobs: Used to fine-tune welding current, voltage, and wire feed speed.

5.2 MIG Welding Operation

  • Turn on the machine and select the MIG welding mode.
  • Open the gas cylinder valve and set the desired gas flow rate on the regulator.
  • Adjust the welding current and voltage according to the material thickness and wire diameter. Refer to welding charts for recommended settings.
  • Press the MIG torch trigger to start welding.

5.3 MMA Welding Operation

  • Turn on the machine and select the MMA welding mode.
  • Insert the appropriate electrode into the electrode holder.
  • Adjust the welding current based on the electrode type and diameter.
  • Strike an arc by lightly touching the electrode to the workpiece and quickly lifting it slightly.

5.4 Pulse Welding (if applicable)

  • Select the Pulse welding mode.
  • Adjust pulse parameters such as peak current, background current, and pulse frequency as needed for specialized applications.

6. Maintenance

Regular maintenance ensures the longevity and optimal performance of your welding machine.

  • Daily: Clean the MIG torch nozzle and contact tip. Check for loose connections.
  • Weekly: Inspect welding cables for damage. Clean the wire feed rollers and guide tube.
  • Monthly: Blow out dust and debris from the machine's interior using compressed air (ensure power is disconnected). Check the condition of the cooling fan.
  • Wire Feed Mechanism: Regularly inspect the wire feed rollers for wear and ensure they are clean and free of debris to maintain consistent wire feeding.

7. Troubleshooting

ProblemPossible CauseSolution
No arc/Poor arc startingImproper ground connection, incorrect settings, worn contact tip/electrode.Ensure ground clamp is secure. Adjust current/voltage. Replace contact tip/electrode.
Inconsistent wire feedWire spool tangled, wire feed rollers too loose/tight, dirty liner.Untangle wire. Adjust roller tension. Clean or replace liner.
Excessive spatterIncorrect voltage/wire speed, insufficient gas flow, dirty workpiece.Adjust settings. Check gas flow. Clean workpiece.
Machine overheatsExceeding duty cycle, blocked ventilation.Allow machine to cool. Clear ventilation openings.

8. Specifications

FeatureSpecification
Model NumberNB-250 (N214II)
TypeOther (MIG/MMA All-in-one)
MaterialPlastic, High Strength Steel, Low Carbon Steel
OriginMainland China, Guangdong, China
Working PrinciplePulse
Welding Speed10-30 cm/min
Welding Rod/Wire Diameter0.8 mm, 1.0 mm
Max Material Thickness3/8 inch
Min Material Thickness0.5 mm
Phase2
Dimension (L x W x H)597 x 298 x 503 mm
High-concerned chemicalNone
Customized SupportOEM, ODM, OBM

9. User Tips

  • Always test your settings on scrap material before welding your main workpiece.
  • Keep your welding area clean and free of flammable materials.
  • For optimal MIG welding results, ensure your gas flow is consistent and appropriate for the material and wire.
  • When switching between MIG and MMA, double-check all connections and settings to match the chosen process.

10. Warranty and Support

10.1 Warranty

The JASIC NB-250 (N214II) welding machine comes with a 3-year warranty from the date of purchase. This warranty covers manufacturing defects under normal use. Please retain your proof of purchase for warranty claims.

10.2 Technical Support

For technical assistance, troubleshooting guidance, or warranty inquiries, please contact our support team:

  • WhatsApp: +86 15053181183
  • Email: 1084674298@qq.com
  • Mobile: +86 15053181183
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.