1. Introduction
This manual provides detailed instructions for the setup, operation, and maintenance of your Xinyi Sini Audio XY-C100H 100W HiFi Bluetooth Digital Amplifier Board Module. Please read this manual thoroughly before use to ensure proper functionality and to maximize your audio experience.
2. Package Contents
Verify that all items listed below are present in your package:
- Xinyi Sini Audio XY-C100H Amplifier Board
- Protective Top Cover
- Heatsink
- Volume Knob
- Standoffs and Screws for assembly
- DC Power Connector

3. Specifications
| Feature | Detail |
|---|---|
| Model | XY-C100H |
| Output Power | 100W (Stereo) |
| Amplifier Chip | TPA3116 |
| Audio Input | Bluetooth, AUX (3.5mm), USB Audio |
| Dimensions (L x W) | 70mm x 65mm |

4. Setup Guide
4.1. Assembly
- Attach the heatsink to the main amplifier chip on the board. Ensure good contact for optimal heat dissipation.
- Mount the protective top cover using the provided standoffs and screws.
- Install the volume knob onto the potentiometer shaft.

4.2. Connections
Before making any connections, ensure the amplifier board is powered off.
- Speaker Output: Connect your passive speakers to the speaker terminals on the board. Ensure correct polarity (+ to + and - to -) for each channel (Left and Right).
- Power Supply: Connect a compatible DC power supply (not included) to the DC power input jack or the screw terminals. Refer to the specifications for the recommended voltage and current.
- Audio Input: Choose one of the following audio input methods:
- AUX IN: Connect an audio source (e.g., smartphone, MP3 player) using a 3.5mm audio cable to the AUX IN port.
- USB Audio: Connect a device (e.g., computer) via a USB cable to the USB Audio port.
- Bluetooth: For wireless connection, refer to the "Operating Instructions" section for pairing.
5. Operating Instructions
5.1. Powering On/Off
Once all connections are secure, connect the power supply to a wall outlet. The amplifier will power on automatically. To power off, disconnect the power supply.
5.2. Volume Control
Rotate the volume knob clockwise to increase the volume and counter-clockwise to decrease it. Start with a low volume setting before playing audio.
5.3. Bluetooth Pairing
- Ensure the amplifier board is powered on.
- On your audio source device (e.g., smartphone), enable Bluetooth and search for available devices.
- Select "XY-C100H" (or similar name) from the list of devices to pair.
- Once paired, audio from your device will be streamed wirelessly to the amplifier.
5.4. AUX Input
When an audio cable is connected to the AUX IN port, the amplifier will automatically switch to AUX input mode. Disconnect the AUX cable to switch back to Bluetooth (if previously paired) or USB Audio.
5.5. USB Audio Input
When a device is connected via USB to the USB Audio port, the amplifier will function as an external sound card for that device. Ensure your device's audio output is set to the amplifier.
6. Maintenance
- Keep the amplifier board clean and free from dust. Use a soft, dry cloth for cleaning.
- Avoid exposing the board to moisture, extreme temperatures, or direct sunlight.
- Ensure adequate ventilation around the heatsink to prevent overheating.
- Do not attempt to disassemble the board beyond the protective cover, as this may void any potential warranty.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No sound output |
|
|
| Bluetooth not pairing |
|
|
| Distorted sound |
|
|
8. User Tips
- For best audio quality, use high-quality audio cables and a stable power supply.
- Consider using a dedicated power supply with sufficient current capacity for optimal performance, especially at higher volumes.
- When switching between input modes (Bluetooth, AUX, USB), ensure the previous connection is properly disconnected or paused to avoid conflicts.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.