Speedybee F405 V5 OX32 55A

Contents

Speedybee F405 V5 OX32 55A Model Aircraft Stack

Flight Controller + 4-in-1 ESC for RC FPV Drones

Model: F405 V5 OX32 55A

1. Introduction

Thank you for choosing the Speedybee F405 V5 OX32 55A Model Aircraft Stack. This integrated flight controller (FC) and electronic speed controller (ESC) system is designed to provide high performance and reliability for your RC FPV drone. This manual will guide you through the installation, configuration, and operation of your new stack.

Video: Speedybee F405 V3 BLS 50A Stack product features overview. Note: Features are generally applicable to V5.

2. Package Contents

Please check the contents of your package against the lists below. If any items are missing or damaged, please contact your retailer.

2.1. Model Aircraft Stack Deluxe Package

Speedybee F405 V5 OX32 55A Deluxe Package Contents

Image: Speedybee F405 V5 OX32 55A Deluxe Package Contents.

  • SpeedyBee F405 V5 Model Aircraft Flight Controller x1
  • SpeedyBee OX32 55A 4-in-1 Model Aircraft ESC x1
  • Soldering Practice Board x1
  • Short-Circuit Protection Tool x1
  • Model Aircraft Stack Connector Cable x1 (SH1.0 10pin*25mm)
  • Model Aircraft Stack Connector Cable x1 (SH1.0 10pin*75mm)
  • DJI Air Unit Connector Cable x1 (SH1.0 6pin*80mm)
  • GPS 6pin Connector Cable + 6pin SH1.0 Terminal x1 (SH1.0 6pin*120mm)
  • GPS 4pin Connector Cable + 4pin SH1.0 Terminal x1 (SH1.0 6pin to SH1.0 4pin*120mm)
  • Type-C Extension Module 4pin Connector Cable x1 (SH1.0 4pin*80mm)
  • Receiver 4pin Connector Cable x1 (SH1.0 4pin*100mm)
  • Buzzer Red & Black Wires x1 (100mm)
  • Active Buzzer x1
  • Type-C Extension Module x1
  • M3 Hex Nylon Nuts x5
  • M3 Black Silicone Washers x5
  • Model Aircraft FC Silicone Covers x5
  • Model Aircraft ESC Silicone Covers x5
  • XT60 Power Cable x1 (120mm)
  • Capacitor Heat Shrink Tube x2
  • M3 Stack Mounting Screws x4 (30mm)
  • Power Expansion Board x4
  • 35V 1000uF Solid Capacitor x1
  • Quick Start Guide for Model Aircraft Stack x1

2.2. Model Aircraft Stack Standard Package

Speedybee F405 V5 OX32 55A Standard Package Contents

Image: Speedybee F405 V5 OX32 55A Standard Package Contents.

  • SpeedyBee F405 V5 Model Aircraft Flight Controller x1
  • SpeedyBee OX32 55A 4-in-1 Model Aircraft ESC x1
  • Model Aircraft Stack Connector Cable x1 (SH1.0 10pin*25mm)
  • Model Aircraft Stack Connector Cable x1 (SH1.0 10pin*75mm)
  • DJI Air Unit Connector Cable x1 (SH1.0 6pin*80mm)
  • GPS 6pin Connector Cable + 6pin SH1.0 Terminal x1 (SH1.0 6pin*120mm)
  • GPS 4pin Connector Cable + 4pin SH1.0 Terminal x1 (SH1.0 6pin to SH1.0 4pin*120mm)
  • Receiver 4pin Connector Cable x1 (SH1.0 4pin*100mm)
  • XT60 Power Cable x1 (120mm)
  • M3 Model Aircraft Stack Mounting Screws x4 (30mm)
  • M3 Hex Nylon Nuts x5
  • M3 Black Silicone Washers x5
  • Capacitor Heat Shrink Tube x2
  • Model Aircraft FC Silicone Covers x5
  • Model Aircraft ESC Silicone Covers x5
  • 35V 1000uF Solid Capacitor x1
  • Quick Start Guide for Model Aircraft Stack x1

3. Specifications

3.1. SpeedyBee F405 V5 Flight Controller

SpeedyBee F405 V5 Flight Controller Specifications

Image: Specifications table for SpeedyBee F405 V5 Flight Controller.

Product NameSpeedyBee F405 V5 30.5x30.5mm Model Aircraft Flight Controller
MCUSTM32F405
IMU (Gyro)ICM42688P
USB Port TypeNew Type-C interface
BarometerSPA06-003
OSD ChipAT7456E
Full-featured Bluetooth TuningSupported. Connect via SpeedyBee App for FC firmware flashing and parameter tuning.
Wireless FC Firmware UpgradeSupported
DJI Air Unit ConnectionSupports 6-pin direct plug-in or solder connection
BlackboxSupported, built-in 16MB storage chip
Input Voltage3-6S LiPo battery
Independent 5V BEC Output2 groups (9x 5V pad on front, 1x BZ+ buzzer pad, and 4x +5V pads at the corners for external LEDs). Total output current: 1.5A.
Independent 9V BEC Output2 groups (1x 9V pad on front, 1x 9V output in a connector on the back). Total output current: 3A. Supports PINIO remote on/off control.
MCU & Gyro PowerIndependent LDO
3.3V Output1 group (1x 3.3V pad on front)
4.5V Output3 groups (3x +4.5V pads on front). Can power receiver and GPS when FC is powered via USB. Max output current: 1A.
ESC SignalM1-M4 pads and 10-pin connector on the back
Servo SignalS5-S6 pads on the front
ESC Telemetry InputSupported (UART5)
Betaflight Camera Tuning PadSupported (CC pad on front)
I2CSupported (GPS connector + pads)
UARTUART1 (Bluetooth); UART2 (front pads for receiver); UART3 (DJI VTX pads + rear SH1.0-6pin); UART4 (GPS pads + front SH1.0-6pin); UART5 (TLM); UART6 (receiver pads + rear SH1.0-4-pin)
ST LED PadsSupported, on front 5V/LED pads; controlled by FC firmware
Meteor LED Strip PadsSupported. Switch between SB-LED and ST-LED modes via BOOT button or App. In SB-LED mode, controlled by ESP32 Bluetooth chip.
Buzzer PadsSupported
BOOT Button[A] Hold BOOT while powering on to force DFU mode for flashing. [B] When powered and in standby, short-press cycles LED display modes; long-press switches SB-LED/ST-LED. In ST-LED mode, LED1-LED4 are controlled by FC firmware.
RSSI PadsSupported
SmartPortNot supported
Supported FC FirmwareBetaflight, INAV, ArduPilot
Firmware Target NameSPEEDYBEEF405V5
Factory Firmware VersionBetaflight 4.5.2
Configurator VersionBetaflight 10.10.0
Mounting Holes30.5 x 30.5mm (Ø4mm), side opening
Dimensions39mm (L) x 39mm (W) x 4.9mm (H)
Weight8.1g

3.2. SpeedyBee OX32 55A 4-in-1 ESC

SpeedyBee OX32 55A ESC Specifications

Image: Specifications table for SpeedyBee OX32 55A 4-in-1 ESC.

Product NameSpeedyBee OX32 55A 30.5x30.5 4-in-1 ESC
Default FirmwareOX32
Continuous Current55A (per channel) / 220A (4-in-1)
Maximum Current70A (per channel) / 280A (4-in-1)
TVS Protective DiodeYes (built-in)
External Capacitor1000uF Solid Capacitor (included in package)
ESC/Motor ProtocolDSHOT300/600
Input Voltage3-6S LiPo
Power OutputVBAT
Current SensorSupported
ESC TelemetrySupported
Mounting Holes30.5 x 30.5mm (Ø4mm), side opening
Dimensions40.9mm (L) x 44.9mm (W) x 8.0mm (H) (incl. heatsink)
Weight19.1g
Current Meter NoteSupported (Scale=27, Offset=-2644)

3.3. Dimensions

SpeedyBee F405 V5 FC and OX32 55A ESC Dimensions

Image: Detailed dimensions for the F405 V5 Flight Controller and OX32 55A ESC.

4. Setup and Installation

4.1. Flight Controller Layout

SpeedyBee F405 V5 Flight Controller Layout

Image: Layout diagram of the F405 V5 Flight Controller with labeled ports and components.

4.2. Wiring Instructions

Proper wiring is crucial for the safe and correct operation of your drone. Refer to the diagrams below for connection methods.

FC and ESC Wiring Instructions

Image: Model Aircraft FC and ESC Wiring Instructions showing soldering, direct plug, standard, and reverse installation methods.

Soldering Method: Connect the FC to the ESC by soldering the corresponding pads (M1-M4, GND, TELEMETRY, etc.) as shown.

Direct Plug Method: Use the provided 10-pin connector cable to connect the FC and ESC directly.

Installation: Use M3 black silicone washers when fixing the Model Aircraft stack to ensure sufficient space between the flight controller and the ESC.

4.3. Detailed Wiring Diagram (Soldered Connection)

Detailed Soldered Wiring Diagram

Image: Detailed Wiring Diagram for Soldered Connection, showing connections for FPV Camera, Buzzer, Servos, LED Strips, GPS, and Receivers.

4.4. FC & Motor Connection

FC and Motor Connection Diagram

Image: Connection diagram for the FC & Motors, showing 1000uF Solid Capacitor and XT60 Power Cable.

Tip: To protect the AIO flight controller from being damaged by instantaneous voltage spikes when powered on, it is strongly recommended to use the included 1000uF solid capacitor.

5. Operating Instructions

5.1. Wireless Tuning

The Speedybee F405 V5 supports full-featured wireless tuning via the Speedybee App. This allows you to configure your FC and ESC settings without needing to connect to a computer.

  1. Download the Speedybee App from your mobile app store.
  2. Connect your drone's battery to power the FC.
  3. Open the Speedybee App and connect to your FC via Bluetooth.
  4. You can now adjust PID tuning, ESC settings (for BLHeli-S/Bluejay), motor directions, and more wirelessly.

5.2. LED Indicators

The FC features 4-level battery life indicators and supports X4 Meteor LED Strips (controllable via Betaflight).

6. Maintenance

  • Conformal Coating: The FC and ESC come with a factory-applied conformal coating for extra protection against moisture, solder residue, plant sap, and other harsh conditions.
  • Cleaning: If necessary, gently clean the boards with isopropyl alcohol and a soft brush. Ensure the device is powered off and completely dry before re-powering.
  • Storage: Store the stack in a dry, cool environment away from direct sunlight and extreme temperatures.

7. Troubleshooting

  • No Power: Check all power connections, ensure the battery is charged, and verify the XT60 power cable is correctly connected.
  • No FC Connection: Ensure the FC is powered, Bluetooth is enabled on your mobile device, and the Speedybee App has necessary permissions. Try restarting both the FC and the app.
  • Motor Issues: Verify motor wiring to the ESC. Use the Speedybee App to check motor directions and ESC settings. Ensure ESC firmware is up to date.
  • Unstable Flight: Check PID tunes in Betaflight. Ensure all sensors (gyro, barometer) are functioning correctly. Verify propeller balance and condition.
  • DFU Mode for Flashing: Hold the BOOT button on the FC while powering on to force it into DFU mode for firmware flashing via USB.

8. User Tips

No specific user tips from reviews or Q&A were available for this product at the time of manual creation.

9. Warranty and Support

Speedybee products are designed for reliability and performance. For warranty claims, technical support, or further assistance, please contact your original retailer or visit the official Speedybee website for their support resources.

Please retain your proof of purchase for warranty purposes.

© 2023 Speedybee. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.