KNOA Adjustable Switching Power Supply User Manual
Models: MS-500W, MS-600W, MS-1000W, MS-1500W
1. Introduction and Overview
This manual provides essential information for the safe and efficient operation of your KNOA Adjustable Switching Power Supply. These power supplies are available in various wattage options (500W, 600W, 1000W, 1500W) and offer adjustable DC output voltages from 0-12V up to 0-220V, with corresponding adjustable output currents. They are designed for a wide range of applications requiring stable and reliable DC power.
The KNOA Adjustable Switching Power Supply features high efficiency, low operating temperature, and comprehensive protection mechanisms including short circuit, overload, and over-voltage protection. It incorporates a built-in cooling fan and an EMI filter for stable performance.
Figure 1: KNOA Adjustable Switching Power Supply Models (500W, 600W, 1000W, 1500W) with adjustable output voltage and current ranges.
2. Safety & Warnings
WARNING: High Voltage Danger. Installation and operation should be performed by qualified personnel.
Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
Keep the device and its cord out of reach of children under 3 years old. Keep away from children unless supervised by an adult.
Do not use this product for purposes other than its intended use.
Inspect the product before each use; do not use if damaged.
Follow installation and operation guidelines to avoid injury.
Do not expose the electrical product to water or moisture.
Handle with care to avoid cuts or injuries, especially during installation.
Ensure proper grounding to prevent electrical shock.
Verify the input voltage switch setting matches your local power supply before connecting.
3. Product Features
Adjustable Output: 0-100% adjustable output voltage and 3-100% (or 10-100% depending on model) adjustable output current.
Input Voltage: AC 110V/220V ±15% (50/60Hz) selectable via a switch.
Cooling: Built-in temperature-controlled DC fan for efficient heat dissipation.
Protections: Short circuit, overload, over-voltage, and over-temperature protection.
Efficiency: High efficiency and low operating temperature.
Soft-Start: Soft-start current reduces AC input impact.
Control: PWM control and regulated output.
Quality Assurance: 100% full-load burn-in test.
EMI Filter: Installed with an EMI filter for minimum ripple and noise.
Internal Components: Features 105 high-performance electrolytic capacitors, pure copper transformer, and FeSiAl pure copper magnetic ring for stable and safe operation.
Figure 2: Internal components of the 500W/600W models, highlighting high-performance capacitors, pure copper transformer, and anti-interference copper coil.Figure 3: Diverse application areas for the KNOA Adjustable Switching Power Supply.
4. Setup Instructions
Unpacking: Carefully remove all protective films from the device.
Input Voltage Selection: Locate the red switch on the side or rear of the power supply. Ensure it is set to match your local AC input voltage (110V or 220V). The factory setting is typically 220VAC. Failure to set this correctly can damage the unit.
Figure 4: Input voltage selection switch (100/240VAC manual switching).
Wiring: Connect the power supply correctly according to the product diagram. Due to high voltage, professional installation is strongly recommended.
AC Input: Connect your AC power source to the L (Live), N (Neutral), and GND (Ground) terminals.
DC Output: Connect your load to the +V (positive) and -V (negative) DC output terminals.
Figure 5: Wiring diagram for MS-1500W models, illustrating input, output, and adjustment points.Figure 6: Wiring diagram for MS-500W/600W models, illustrating input, output, and adjustment points.
5. Operating Instructions
Power On: After ensuring all connections are secure and the input voltage switch is correctly set, apply AC power. The power indicator light should illuminate.
Voltage Adjustment: Use a small screwdriver to carefully turn the 'V ADJ' potentiometer to adjust the output DC voltage to your desired level. The digital display (if present on your model) will show the current output voltage.
Current Adjustment: Use a small screwdriver to carefully turn the 'A ADJ' potentiometer to adjust the output current limit. This allows you to set the maximum current the power supply will deliver.
Video 1: Demonstration of voltage and current adjustment on a 1500W digital display power supply.
6. Maintenance
Cleaning: Keep the power supply free from dust and debris. Use a soft, dry cloth for cleaning. Do not use liquid cleaners.
Cooling: Ensure that the cooling fan vents are not obstructed to allow for proper airflow. The built-in temperature-controlled fan will activate when the internal temperature rises above 45 °C.
Figure 7: Temperature-controlled cooling fan for efficient heat management.
Storage: When not in use, turn off the device and store it in a dry, well-ventilated place, away from direct sunlight and extreme temperatures. Keep away from children.
7. Troubleshooting
No Output Power:
Check if the AC input power is connected and active.
Verify the input voltage switch is correctly set (110V/220V).
Ensure all wiring connections are secure.
Overload Protection: If the output current exceeds the set limit, the power supply may automatically cut off. Reduce the load connected to the output and restart the power supply.
Over-Voltage Protection: If the output voltage exceeds a safe limit, the power supply may cut off. Check your voltage settings and ensure they are within the acceptable range for your load. Restart the power supply.
Over Temperature Protection: If the internal temperature becomes too high, the power supply will shut down to prevent damage. Allow the unit to cool down, ensure adequate ventilation, and then restart.
8. Specifications
General Specifications
Attribute
Value
Brand Name
KNOA
Model Number
MS-500W/600W/1000W/1500W
Type
Power Supply
Input Voltage
AC 110/220V SMPS
Output Voltage
DC 12V to 220V (Adjustable)
Output Current
0-125A (Adjustable, varies by model/voltage)
Output Power
>500W (500W, 600W, 1000W, 1500W)
Output Frequency
50-60Hz
Output Type
SINGLE
Rated Capacity
>1000VA
EU LVD Voltage
High voltage: Above 50Vac or 75Vdc
Certification
CE, FCC, RoHS
Origin
Mainland China
Model-Specific Output Ranges and Dimensions
MS-500W Adjustable Power Supply
Output Voltage Range (Adjustable)
Continuously Adjustable Max Output Current
0-12V (Adjustable up to 13.2V)
0.5-40A
0-15V (Adjustable up to 16.5V)
0.5-33A
0-24V (Adjustable up to 26.5V)
0.5-20A
0-27V (Adjustable up to 30V)
0.5-18.5A
0-30V (Adjustable up to 33V)
0.5-13A
0-36V (Adjustable up to 40V)
0.5-13.5A
0-48V (Adjustable up to 53V)
0.5-10A
0-60V (Adjustable up to 66V)
0.5-8.3A
0-68V (Adjustable up to 72V)
0.5-7.3A
0-72V (Adjustable up to 80V)
0.5-7.0A
0-85V (Adjustable up to 90V)
0.5-5.8A
0-90V (Adjustable up to 95V)
0.5-5.5A
0-100V (Adjustable up to 105V)
0.5-5.0A
0-110V (Adjustable up to 115V)
0.5-4.5A
0-150V (Adjustable up to 155V)
0.3-3.3A
0-200V (Adjustable up to 203V)
0.3-2.5A
Figure 8: MS-500W Output Voltage and Current Ranges.
MS-600W Adjustable Power Supply
Output Voltage Range (Adjustable)
Continuously Adjustable Max Output Current
0-12V (Adjustable up to 13.2V)
0.5-50A
0-15V (Adjustable up to 16.5V)
0.5-40A
0-24V (Adjustable up to 26.5V)
0.5-25A
0-27V (Adjustable up to 30V)
0.5-22A
0-30V (Adjustable up to 33V)
0.5-20A
0-36V (Adjustable up to 40V)
0.5-16.5A
0-48V (Adjustable up to 53V)
0.5-12.5A
0-60V (Adjustable up to 66V)
0.5-10A
0-68V (Adjustable up to 72V)
0.5-8.8A
0-72V (Adjustable up to 80V)
0.5-8.3A
0-85V (Adjustable up to 90V)
0.3-7.0A
0-90V (Adjustable up to 95V)
0.3-6.5A
0-100V (Adjustable up to 105V)
0.3-6.0A
0-110V (Adjustable up to 115V)
0.3-5.5A
0-150V (Adjustable up to 155V)
0.3-4.0A
0-200V (Adjustable up to 203V)
0.3-3.0A
Figure 9: MS-600W Output Voltage and Current Ranges.
MS-1000W Adjustable Power Supply
Output Voltage Range (Adjustable)
Continuously Adjustable Max Output Current
0-12V (Adjustable up to 15V)
0-83A
0-15V (Adjustable up to 17V)
0-67A
0-24V (Adjustable up to 27V)
0-41A
0-27V (Adjustable up to 30V)
0-37A
0-30V (Adjustable up to 33V)
0-33A
0-36V (Adjustable up to 40V)
0-27A
0-48V (Adjustable up to 53V)
0-21A
0-60V (Adjustable up to 66V)
0-16.7A
0-68V (Adjustable up to 72V)
0-13.5A
0-72V (Adjustable up to 75V)
0-13.8A
0-85V (Adjustable up to 90V)
0-12A
0-90V (Adjustable up to 95V)
0-11A
0-100V (Adjustable up to 105V)
0-10A
0-110V (Adjustable up to 115V)
0-9A
0-150V (Adjustable up to 157V)
0-6.7A
0-200V (Adjustable up to 210V)
0-5A
Figure 10: MS-1000W Output Voltage and Current Ranges.
MS-1500W Adjustable Power Supply
Output Voltage Range (Adjustable)
Continuously Adjustable Max Output Current
0-12V (Adjustable up to 15V)
0-125A
0-15V (Adjustable up to 17V)
0-100A
0-24V (Adjustable up to 27V)
0-62.5A
0-27V (Adjustable up to 30V)
0-55.5A
0-30V (Adjustable up to 33V)
0-50A
0-36V (Adjustable up to 40V)
0-42A
0-48V (Adjustable up to 53V)
0-32A
0-60V (Adjustable up to 66V)
0-25A
0-68V (Adjustable up to 72V)
0-22A
0-72V (Adjustable up to 75V)
0-20.8A
0-85V (Adjustable up to 90V)
0-17A
0-90V (Adjustable up to 95V)
0-16.7A
0-100V (Adjustable up to 105V)
0-15A
0-110V (Adjustable up to 115V)
0-13.6A
0-150V (Adjustable up to 157V)
0-10A
0-200V (Adjustable up to 210V)
0-7.5A
Figure 11: MS-1500W Output Voltage and Current Ranges.
100%-105% of rated output power, start overload protection. Protection mode: current limiting mode, it can be automatically restored after the abnormal condition of negative cut is removed.
Over-voltage Protection
115%-135% of rated output voltage starts overvoltage protection. Protection mode: Snatch mode, it can be automatically restored after the abnormal load condition is removed.
Over Temperature Protection
Power tube temperature ≥ 95°C ±5% start over-temperature protection. Protection mode: cut off the output, and it will automatically recover when the temperature returns to normal.
Working Temperature, Humidity
-20°C - +60°C, 20%-90%RH (please refer to the load derating curve)
Storage Temperature, Humidity
-40°C - +85°C, 10%-95%RH non-condensing
Shock Resistance
10-500Hz, 2G 10min/1 cycle, duration 60 minutes, each axis
Pressure Resistance
Between input and output (VP-O/P): 1.5KVAC Input and ground (UPFG): 1.5KVAC Output and ground (O/P-FG): 0.5KVAC
Insulation Resistance
Between input and output (P-O/P) input and ground (VP-FG), output and ground (O/P-FG): 100M Ohms/500VDC/25°C/70%RH
Safety Standard
Comply with IEC60950-1GB4943
EMC Standard
Compliant with EN55022 Class A, GB9254 Class A
Electromagnetic Compatibility
Conforms to EN61000-4-2,3,4,5,6,8,11
Size (L×W×H)
248×133×70mm
Weight
1.95Kg
Figure 12: Detailed Specifications for MS-1000W Series (similar for other wattages).
Notes on Specifications:
Unless otherwise specified, all parameters are measured under the conditions of 230VAC voltage input, rated load and 25 °C.
The ripple and noise voltages are measured on a 20MHz bandwidth oscilloscope with 0.1µ and 47µ capacitors at the ends of a 12-inch twisted pair.
The capacity is the sum of voltage setting error, voltage adjustment rate and current adjustment rate.
The power supply should be regarded as a part of the system, and its electromagnetic compatibility needs to be confirmed in conjunction with the terminal equipment.
9. User Tips
Optimal Lifespan: For optimal lifespan and stable operation, it is recommended that the maximum power usage does not exceed 80% of the power supply's full rated load.
Efficiency: Users have noted excellent idle power consumption (as low as 2W), indicating high efficiency.
New Upgraded Circuit: Some models may come with a new upgraded circuit version where the output port has been repositioned. This makes it easier to regulate voltage and current. Product models and functions remain consistent.
Figure 13: Old vs. New Upgraded Circuit Version (output port repositioned for easier adjustment).
10. Manufacturer & Support Information
Manufacturer
Company Name: SHENZHEN KNOA TECHNOLOGY CO., LTD.
Address: Unit 1606, 1, Building B, Jida Garden, 38 Jinyun Road, Nansan Community, Buji Street, Longgang District, Shenzhen
Email: 294411620@qq.com
Telephone: +86 15889456615
EU Authorized Representative
Company Name: MJCMSARL
Address: FR-78 Avenue des Champs Elysees, Office 326
Email: mjcm190928@gmail.com
Telephone: +33 767213611
Compliance Information
This product complies with all applicable safety and regulatory requirements in the market where it is sold. It meets the following directives and standards:
Directives: LVD Directive 2014/35/EU
Test Standards: EN IEC 62368-1:2024/A11:2024
Certifications: CE, FCC, RoHS
For further detailed compliance information, please refer to the official user manual PDF referenced as User manual (PDF).
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.