1. Introduction
The CERTEON TA500C is a versatile digital laser tachometer designed for accurate measurement of rotational speed (RPM), linear speed, and length. It offers both contact and non-contact measurement modes, making it suitable for a wide range of industrial and automotive applications. This manual provides detailed instructions for the safe and efficient operation of your device.


2. Safety Information
Please read and understand all safety warnings and operating instructions before using this device. Failure to do so may result in injury or damage to the instrument.
- Do not point the laser beam directly at eyes or reflective surfaces.
- Ensure the device is powered off when not in use or during battery replacement.
- Keep the device away from water and extreme temperatures.
- Use only the specified battery type.
- Do not attempt to disassemble or modify the device.
3. Product Components and Controls
The TA500C tachometer features a clear LCD screen and intuitive button controls:
- LCD Screen: Displays measurement readings, units, battery level, and mode indicators.
- Backlight: Illuminates the screen for visibility in low-light conditions.
- UNIT Button: Switches between measurement units (RPM, m/min, ft/min, m).
- TEST Button: Activates the laser for non-contact measurement or starts contact measurement.
- MAX Button: Toggles between Maximum, Minimum, and Average value display.
- HOLD Button: Freezes the current reading on the display.
- Power Button: Turns the device ON/OFF.

4. Setup and Preparation
4.1 Battery Installation
- Ensure the device is powered off.
- Locate the battery compartment cover on the back of the tachometer.
- Slide or unclip the cover to open.
- Insert 2 x 1.5V AAA batteries (for TA500A/B/C models) or 3 x 1.5V AA batteries (for TA503A/B/C models), observing the correct polarity (+/-).
- Replace the battery compartment cover securely.

4.2 Preparing for Non-Contact Measurement
For non-contact RPM measurement, a reflective tape must be applied to the rotating object.
- Clean the surface of the rotating object where the measurement will be taken.
- Cut a small piece of the provided reflective tape.
- Apply the reflective tape to the rotating object. Ensure it is flat and securely adhered.

4.3 Preparing for Contact Measurement (TA500C, TA503C, TA500B, TA503B models)
For contact measurement of RPM, linear speed, or length, attach the appropriate contact accessories.
- Ensure the device is powered off.
- Select the desired contact accessory (e.g., cone tip, funnel tip, or surface wheel).
- Carefully attach the accessory to the measurement shaft at the top of the tachometer.


5. Operating Instructions
5.1 Powering On/Off
Press the Power button (①) to turn the tachometer ON. Press and hold the Power button again to turn it OFF. The device features an auto power-off function after 15 minutes of inactivity (can be disabled on some models).
5.2 Non-Contact Measurement (RPM)
- Ensure reflective tape is applied to the rotating object (refer to Section 4.2).
- Press the UNIT button to select the RPM mode (indicated by "RPM" on the display).
- Aim the laser beam perpendicularly at the reflective tape on the rotating object.
- Press the TEST button to activate the laser. The laser symbol (▲) will flash.
- Maintain a distance of 50mm to 500mm between the tachometer and the object.
- The RPM reading will be displayed on the LCD screen.
- Release the TEST button to stop measurement.

5.3 Contact Measurement (RPM, Linear Speed, Length)
This applies to TA500C, TA503C, TA500B, TA503B models.
- Attach the appropriate contact accessory (refer to Section 4.3).
- Press the UNIT button to cycle through RPM, m/min, ft/min, or m modes.
- Gently press the contact accessory against the rotating surface or object to be measured.
- Press the TEST button to begin measurement. The corresponding unit symbol will flash.
- Read the measurement value on the LCD screen.
- Release the TEST button to stop measurement.

5.4 Max/Min/Hold Functions
- MAX/MIN: During measurement, press the MAX button to display the maximum recorded value. Press it again to display the minimum value. Press a third time to display the average value.
- HOLD: Press the HOLD button to freeze the current reading on the display. Press it again to resume live measurement.

5.5 Data Storage (TA503A/B/C models)
These models can store up to 2000 sets of data. Refer to the specific model's detailed manual for instructions on accessing and managing stored data.
5.6 USB Communication (TA503C model only)
The TA503C model supports USB communication for data export. Connect the device to a PC using a USB cable. Use the dedicated software (provided separately or available for download) to export data to Excel spreadsheets and view real-time measurement curves.
6. Maintenance
- Cleaning: Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Battery Replacement: Replace batteries when the low battery indicator appears on the display. Remove batteries if the device will not be used for an extended period to prevent leakage.
- Storage: Store the tachometer in a cool, dry place, away from direct sunlight and extreme temperatures. The recommended storage environment is -10°C to 50°C with max 70% RH (battery removed).
- Contact Accessories: Clean contact accessories after each use to ensure accurate readings.
7. Troubleshooting
- No Display/Device Not Turning On: Check battery installation and ensure batteries are not depleted. Replace if necessary.
- Inaccurate Non-Contact Reading:
- Ensure reflective tape is clean, flat, and securely applied.
- Verify the measurement distance is within 50mm to 500mm.
- Ensure the laser is aimed directly at the reflective tape.
- Inaccurate Contact Reading:
- Ensure the contact accessory is clean and properly attached.
- Apply consistent pressure when making contact with the rotating object.
- Low Battery Indicator: Replace batteries immediately to ensure accurate operation.
8. Specifications
The following table details the technical specifications for the TA500 series tachometers:

| Parameter | TA500A | TA500B | TA500C | TA503A | TA503B | TA503C |
|---|---|---|---|---|---|---|
| Measurement Method | Non-contact | Contact | Contact + Non-contact | Non-contact | Contact | Contact + Non-contact |
| RPM Range | 3~99999 RPM | 3~19999 RPM | Laser: 3-99999 RPM Contact: 0-19999 RPM | 3-99999 RPM | 3-19999 RPM | Laser: 3-99999 RPM Contact: 3-19999 RPM |
| Linear Speed Range | – | 0-1999.9 m/min 0-9999.9 ft/min | Same as TA500B | – | Same as TA500B | Same as TA500B |
| Length Measurement | – | 0-999999 m | Same as TA500B | – | Same as TA500B | Same as TA500B |
| Accuracy | ±(0.05%+1 digit) | ±(0.1%FS+1 RPM) ±(0.1%FS+0.2 m/min) ±(0.1%FS+0.6 ft/min) | Laser: ±(0.05%FS+1 RPM) Contact: ±(0.1%FS+1 RPM) | ±(0.05%FS+1 RPM) | Same as TA500B | Same as TA500B |
| Display | 6-digit LCD | 6-digit LCD | 6-digit LCD | 5-digit LCD | 5-digit LCD | 5-digit LCD |
| Sampling Time | 0.8s (≥60 RPM) | 0.8s (≥60 RPM) | 0.8s (≥60 RPM) | 0.8s (≥60 RPM) | 0.8s (≥60 RPM) | 0.8s (≥60 RPM) |
| Data Storage | – | – | – | 2000 records | 2000 records | 2000 records |
| Alarm Function | – | – | – | Sound + Light | Sound + Light | Sound + Light |
| USB Communication | – | – | – | – | – | Yes (TA503C only) |
| Effective Measuring Distance | 50mm ~ 500mm | N/A | 50mm ~ 500mm (Non-contact) | 50mm ~ 500mm | N/A | 50mm ~ 500mm (Non-contact) |
| Auto Power Off | 15 mins (can be disabled) | 15 mins (can be disabled) | 15 mins (can be disabled) | 15 mins (can be disabled) | 15 mins (can be disabled) | 15 mins (can be disabled) |
| Working Environment | -10 ~ 50°C, Max 80%RH, indoor altitude < 2000m | |||||
| Storage Environment | -10 ~ 50°C, Max 70%RH (battery removed) | |||||
| Product Size | 130x59x29mm | 130x59x29mm | 146x59x29mm | 130x59x29mm | 130x59x29mm | 146x59x29mm |
| Screen Size | 34x31mm | 34x31mm | 34x31mm | 34x31mm | 34x31mm | 34x31mm |
| Weight | Approx. 110g | Approx. 117g | Approx. 120g | Approx. 110g | Approx. 117g | Approx. 120g |
| Power | 2 x 1.5V AAA | 2 x 1.5V AAA | 2 x 1.5V AAA | 3 x 1.5V AA or 5V USB | 3 x 1.5V AA or 5V USB | 3 x 1.5V AA or 5V USB |
9. User Tips
- For non-contact measurements, ensure the reflective tape is applied smoothly and covers a sufficient area for the laser to detect.
- When using contact mode, apply gentle but firm pressure to avoid slippage and ensure accurate readings.
- If measuring very low RPMs, ensure the sampling time is sufficient for stable readings.
- For models with data storage, regularly transfer important data to a computer to prevent loss.
10. Frequently Asked Questions (FAQ)
- Q1: Can this device measure both rotational and linear speed?
- A1: Yes, models TA500B, TA500C, TA503B, and TA503C can measure RPM, linear speed, and length.
- Q2: Is the laser sensor safe to use?
- A2: Yes, it uses a low-power semiconductor laser that is stable and safe for industrial applications. However, avoid direct eye exposure.
- Q3: How can I export the data to a computer?
- A3: Only the TA503C model supports USB communication. Use the dedicated software to export Excel files and view data curves.
11. Warranty and Support
For technical support, warranty inquiries, or customized product needs, please contact CERTEON Automation Store directly.

WhatsApp: +86 19542723588
Email: celiachen008@gmail.com