EPMAN EP-GA50

Contents

EPMAN Racing 2" 52mm Digital Analog LED Gauge Instruction Manual

Model: EP-GA50 Series

1. Product Overview

The EPMAN Racing 2" (52mm) Digital Color Analog LED Gauge series offers a range of automotive monitoring gauges designed for gasoline vehicles. These gauges feature a smoked tint lens when off and a vibrant color LED display when on, providing both digital and analog LED readouts. The series includes gauges for Boost, Oil Pressure, Water Temperature, Oil Temperature, Exhaust Gas Temperature (EGT), Air/Fuel Ratio (AFR), Tachometer, and Volts.

EPMAN 2-inch 52mm Digital Analog LED Boost Gauge showing a reading of 98, with other gauge types displayed below.
EPMAN 2-inch 52mm Digital Analog LED Boost Gauge showing a reading of 98, with other gauge types displayed below.
Collection of EPMAN 2-inch 52mm Digital Analog LED gauges, including Air/Fuel Ratio, Boost, RPM, Oil Temp, EGT Temp, Water Temp, Oil Press, and Volts.
Collection of EPMAN 2-inch 52mm Digital Analog LED gauges, including Air/Fuel Ratio, Boost, RPM, Oil Temp, EGT Temp, Water Temp, Oil Press, and Volts.
Short video demonstrating the EPMAN digital analog LED gauge in operation, showing its color display and scanning feature.

2. Package Contents

Each EPMAN EP-GA50 series gauge typically includes the following components:

  • 1 x Digital Analog LED Gauge (specific type varies by order)
  • 1 x Gauge Pod (52mm bracket)
  • 1 x Instructions in English
  • Mounting hardware (screws, adhesive pads)
  • Specific sensor(s) and/or tubing depending on the gauge type (e.g., Boost Sensor, Oil Temp Sensor, Water Temp Sensor, EGT Sensor)
Components included with the gauge: the gauge unit, wiring, clear tubing, mounting screws, and adhesive pads.
Components included with the gauge: the gauge unit, wiring, clear tubing, mounting screws, and adhesive pads.
Four views of the EPMAN gauge and its included gauge pod, showing front, back, side, and bottom angles.
Four views of the EPMAN gauge and its included gauge pod, showing front, back, side, and bottom angles.

3. Setup and Installation

Important: Installation tools and a comprehensive instruction manual are not included with the product. Professional installation is strongly recommended to ensure correct wiring and functionality, and to prevent damage to the product or vehicle.

3.1. General Fitment

  • These gauges are designed to fit most gasoline vehicles.
  • They are compatible with 2" or 52mm diameter gauge pods/holders.
  • Placement on Vehicle: FRONT.

3.2. Wiring Considerations

The gauge wiring colors may vary from typical installation diagrams. Always refer to the included English instructions for specific wiring details for your particular gauge type. Ensure all connections are secure and properly insulated.

3.3. Sensor Installation

For gauges requiring sensors (e.g., EGT, Oil Temp, Water Temp, Oil Pressure, Boost), ensure the sensor is installed correctly according to the vehicle's specifications and the sensor's thread size (typically 1/8" NPT for temperature and pressure sensors).

4. Operating Instructions

The EPMAN EP-GA50 series gauges feature a smoked tint lens when off and illuminate with a color LED display when powered on. They provide both digital and analog LED readouts for clear monitoring.

4.1. Power On/Off

  • When the vehicle's ignition is turned on, the gauge will perform a scanning sequence (green-yellow-red) before displaying the current reading.
  • When the ignition is turned off, the gauge will revert to its smoked tint appearance.

4.2. Unit Type Selection (Dial Switch)

Many gauges in the EP-GA50 series allow you to change the unit type (e.g., °C/F, BAR/PSI) using a dial switch. Refer to the specific instructions included with your gauge for details on how to access and operate this switch.

4.3. Gauge Specific Operation

Gauge TypeModelUnit TypeDisplay RangeDigital Accuracy
TachometerEP-GA50RPMRPM0-100*100RPMN/A
Exhaust Gas TempEP-GA50EXTT°C/F20~120(*10°C)/39~219 (*10 F)Every 10°C/10F
Turbo BoostEP-GA50BOOSTBAR/PSI-1.0~3.0BAR/-15~45PSIEvery 0.1BAR/1PSI
Air Fuel RatioEP-GA50AIFRAFR20~10 AFREvery 1AFR
Oil TemperatureEP-GA50OILT°C/F50~150 °C /100~300FEvery 1 °C /1F
Oil PressureEP-GA50OILPPSI/Bar0~145PSI/0~10BAREvery 1 PSI /0.5BAR
Water TemperatureEP-GA50WAT°C/F50~150 °C /100~300FEvery 1 °C /1F
Volt GaugeEP-GA50VOLTV8.0~18.0VEvery 1V

5. Maintenance

To ensure the longevity and accurate performance of your EPMAN gauge, follow these general maintenance guidelines:

  • Cleaning: Use a soft, dry cloth to clean the gauge face and body. Avoid abrasive cleaners or solvents that could damage the lens or finish.
  • Connections: Periodically check all wiring connections to ensure they are secure and free from corrosion.
  • Sensor Integrity: Inspect sensors for any signs of damage or wear. Replace faulty sensors promptly.
  • Environmental Factors: While designed for automotive use, extreme temperatures or moisture can affect performance. Ensure proper sealing and protection where necessary.

6. Troubleshooting

  • No Display/Incorrect Reading: Check all power and ground connections. Verify sensor wiring is correct and the sensor itself is functioning.
  • EGT Gauge Reading '20' Constantly: For the Exhaust Gas Temperature (EGT) gauge, if the actual temperature has not reached 200°C, the reading will typically show '20' and will not change until the temperature exceeds this threshold. This is considered normal operation.
  • Intermittent Readings: This could indicate a loose connection or a faulty sensor. Re-check all wiring and consider testing the sensor.

7. Specifications

  • Brand: EPMAN
  • Model Series: EP-GA50
  • Type: Digital Color Analog LED Gauge
  • Size: 2" (52mm) Diameter
  • Material: PVC
  • Item Weight: 0.5 kg
  • LED Color: Blue (main digital display)
  • Scanning Colors: Green-Yellow-Red (analog LED segments)
  • Placement on Vehicle: Front
  • Country/Region of Manufacture: China
  • Special Features: Universal fitment for 1-10 Cylinder Spark Ignition Motors
  • Warranty: Yes (3 Months)

7.1. Input Resistance/Voltage (where applicable)

  • Oil Temperature Gauge: Input Resistant: 1970~30Ω
  • Oil Pressure Gauge: Input Voltage: 10~184Ω
  • Tachometer Gauge: Input Type: K type thermocouple
  • Volt Gauge: Input Type: K type thermocouple

8. Warranty and Support

This product comes with a 3-month warranty. In case of a warranty claim, the gauge will need to be returned to China for repair.

For detailed installation instructions and further technical information, please refer to the official user manual PDF:

User manual (PDF): View PDF Manual

As professional installation is highly recommended, EPMAN takes no responsibility in teaching users how to install the product. Please consult with a qualified automotive technician for installation assistance.

9. User Tips

  • Always double-check wiring connections before powering on the gauge to prevent electrical issues.
  • Ensure sensors are properly sealed and positioned to get accurate readings and prevent leaks.
  • If you are unsure about any part of the installation process, seek professional assistance.
  • Keep the gauge face clean for optimal visibility of both digital and analog displays.

© 2024 EPMAN Racing. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.