SUMRY HGX 4KW 110V

Contents

SUMRY HGX 4KW 24V 110/120V Pure Sine Wave MPPT Solar Charge Hybrid Inverter

Model: HGX 4KW 110V | Brand: SUMRY

1. Introduction

1.1 Purpose and Scope

This manual describes the assembly, installation, operation, and troubleshooting of the SUMRY HGX 4KW 24V 110/120V Pure Sine Wave MPPT Solar Charge Hybrid Inverter. Please read this manual carefully before installation and operation. Keep this manual for future reference. This manual provides safety and installation guidelines, along with information on tools and wiring.

1.2 Features

  • Off-grid solar inverter functionality.
  • No battery function available (SBU mode: utility power, battery, and PV power complement each other).
  • Under Battery Mode, AC voltage can be adjusted to 100VAC, 110VAC, and 120VAC.
  • Pure sine wave solar inverter.
  • Unique glass top cover design with a 6.25-inch LCD display and touchable buttons.
  • Built-in 150A MPPT solar charger (Max PV 5600W).
  • High PV input range from 55V-450Vdc.
  • Smart battery charger design for optimized battery performance.
  • Configurable AC/Battery input priority via LCD setting.
  • Auto restart while PV is recovering.
  • Over-load, over temperature, and output short circuit protection.
  • Cold restart function.
  • Built-in lithium battery automatic activation.
  • Communication with RS232/RS485.
  • WiFi monitoring function (optional).
  • Anti-dust kit for harsh environments (optional).
  • Restore default settings with one click.

1.3 Basic System Architecture

The inverter/charger can be integrated into a system that includes a generator or utility power source and optional PV modules. It is designed to power various home or office appliances, including motor-type appliances like refrigerators and air conditioners.

Diagram showing the hybrid power system architecture with solar power, generator/utility, battery, inverter, and home appliances.
Figure 1: Hybrid Power System Diagram

1.4 Product Overview

The inverter features a comprehensive display and various connection ports.

Front view of the inverter showing LCD display, status indicators, charging indicator, fault indicator, and function touch buttons.
Figure 2: Front Panel Overview

Front Panel Components:

  1. LCD display
  2. Status indicator
  3. Charging indicator
  4. Fault indicator
  5. Function touch buttons
Side view of the inverter showing connection ports labeled Battery input, AC output, RS458/RS232 communication port, AC input, and PV input.
Figure 3: Connection Ports Overview

Rear/Side Panel Components:

  1. Power on/off switch
  2. AC input
  3. AC output
  4. PV input
  5. Battery input
  6. RS485/RS232 communication port

2. Safety Instructions

WARNING: This chapter contains important safety and operating instructions. Read and keep this manual for future reference.

  1. Before using the unit, read all instructions and cautionary markings on the unit, the batteries, and all appropriate sections of this manual.
  2. CAUTION – To reduce risk of injury, charge only deep-cycle lead-acid type rechargeable batteries. Other types of batteries may burst, causing personal injury and damage.
  3. Do not disassemble the unit. Take it to a qualified service center when service or repair is required. Incorrect re-assembly may result in a risk of electric shock or fire.
  4. To reduce risk of electric shock, disconnect all wirings before attempting any maintenance or cleaning. Turning off the unit will not reduce this risk.
  5. CAUTION – Only qualified personnel can install this device with battery.
  6. NEVER charge a frozen battery.
  7. For optimum operation of this inverter/charger, please follow required specifications to select appropriate cable size. It's very important to correctly operate this inverter/charger.
  8. Be very cautious when working with metal tools on or around batteries. A potential risk exists to drop a tool to spark or short circuit batteries or other electrical parts and could cause an explosion.
  9. Please strictly follow installation procedure when you want to disconnect AC or DC terminals. Please refer to the INSTALLATION section of this manual for details.
  10. GROUNDING INSTRUCTIONS - This inverter/charger should be connected to a permanent grounded wiring system. Be sure to comply with local requirements and regulations to install this inverter.
  11. NEVER cause AC output and DC input short-circuited. Do NOT connect to the mains when DC input short circuits.
  12. Warning!! Only qualified service persons are able to service this device. If errors still persist after following troubleshooting table, please send this inverter/charger back to local dealer or service center for maintenance.

3. Installation

3.1 Unpacking and Inspection

Before installation, inspect the unit. Ensure that nothing inside the package is damaged. You should have received the unit and this user manual.

3.2 Preparation

Before connecting all wirings, remove the bottom cover by unscrewing two screws.

3.3 Mounting the Unit

Consider the following points when selecting an installation location:

  • Do not mount the inverter on flammable construction materials.
  • Mount on a solid surface.
  • Install this inverter at eye level to allow the LCD display to be read at all times.
  • The ambient temperature should be between 0°C and 55°C for optimal operation.
  • The recommended installation position is vertically on the wall.
  • Ensure sufficient space (at least 20cm on sides, 50cm above and below) for heat dissipation and wire removal.

SUITABLE FOR MOUNTING ON CONCRETE OR OTHER NON-COMBUSTIBLE SURFACE ONLY.

3.4 Battery Connection

CAUTION:

For safety and regulation compliance, install a separate DC over-current protector or disconnect device between the battery and inverter. Over-current protection is always required.

WARNING:

All wiring must be performed by qualified personnel. Use appropriate cable for battery connection to ensure system safety and efficient operation. Refer to the table below for recommended cable and terminal sizes.

Recommended Battery Cable and Terminal Size
ModelTypical AmperageBattery CapacityWire SizeCable (mm²)Torque Value
3.0KW 24V110A100AH1*4AWG222~3 Nm
3.0KW 24V110A200AH1*4AWG222~3 Nm
4.0KW 24V150A200AH1*2AWG352~3 Nm

Battery Connection Steps:

  1. Assemble battery ring terminals based on recommended cable and terminal sizes.
  2. Connect all battery packs as required by the unit.
  3. Insert the ring terminal of the battery cable flatly into the inverter's battery connector. Ensure bolts are tightened with a torque of 2-3 Nm. Verify correct polarity at both the battery and the inverter/charger, and ensure ring terminals are securely screwed to the battery terminals.

NOTE: Only use sealed lead-acid, GEL/AGM lead-acid, or lithium batteries.

WARNING: Shock Hazard! Installation must be performed with care due to high battery voltage in series.

CAUTION: Do not place anything between the flat part of the inverter terminal and the ring terminal. Otherwise, overheating may occur. Do not apply anti-oxidant substance on the terminals before they are connected tightly. Before making the final DC connection or closing the DC breaker/disconnector, ensure positive (+) is connected to positive (+) and negative (-) to negative (-).

3.5 AC Input/Output Connection

CAUTION:

Before connecting to an AC input power source, install a separate AC breaker between the inverter and the AC input power source. This ensures the inverter can be securely disconnected during maintenance and is fully protected from over-current. Recommended AC breaker specs: 32A for 3.0KW, 40A for 4.0KW. There are two terminal blocks labeled “INPUT” and “OUTPUT”. Do NOT mis-connect input and output connectors.

WARNING:

All wiring must be performed by qualified personnel. Use appropriate cable for AC input connection for system safety and efficient operation. Refer to the table below for recommended cable sizes.

Suggested Cable Requirement for AC Wires
ModelGaugeTorque Value
3.0KW10 AWG1.2~1.6 Nm
4.0KW8 AWG1.4~1.6 Nm

AC Input/Output Connection Steps:

  1. Before making AC input/output connections, open the DC protector or disconnector first.
  2. Remove 10mm of insulation sleeve for six conductors. Shorten phase L and neutral conductor N by 3mm.
  3. Insert AC input wires according to polarities indicated on the terminal block and tighten the terminal screws.
  4. Insert AC output wires according to polarities indicated on the terminal block and tighten the terminal screws. Be sure to connect the PE protective conductor (Ground, green) first.
  5. Make sure the wires are securely connected.

WARNING: Be sure that AC power source is disconnected before attempting to hardwire it to the unit.

CAUTION: Important! Be sure to connect AC wires with correct polarity. If L and N wires are connected reversely, it may cause utility short-circuited when these inverters are operated in parallel. Appliances such as air conditioners require at least 2-3 minutes to restart. If a power shortage occurs and recovers quickly, it can damage connected appliances. Check if the air conditioner has a time-delay function before installation.

3.6 PV Connection

CAUTION:

Before connecting to PV modules, install a DC circuit breaker separately between the inverter and PV modules.

WARNING:

All wiring must be performed by qualified personnel. Use appropriate cable for PV module connection for system safety and efficient operation. Refer to the table below for recommended cable sizes.

Recommended Cable Requirement for PV Module Connection
ModelWire SizeCable (mm²)Torque Value (max)
3.0KW/4.0KW1 x 12AWG41.2 Nm

PV Module Selection:

When selecting proper PV modules, consider the following parameters:

  1. Open circuit Voltage (Voc) of PV modules must not exceed the max. PV array open circuit voltage of the inverter.
  2. Open circuit Voltage (Voc) of PV modules should be higher than the min. PV Array MPPT Voltage range.
Inverter Model PV Specifications
INVERTER MODEL3.0KW4.0KW
Max. PV Array Open Circuit Voltage350Vdc
PV Array MPPT Voltage Range55Vdc~350Vdc
Diagram illustrating series and parallel wiring methods for solar photovoltaic panels, including voltage and current calculations.
Figure 4: Solar Photovoltaic Panel Wiring Methods

PV Module Connection Steps:

  1. Remove 10mm of insulation sleeve for positive and negative conductors.
  2. Check correct polarity of connection cable from PV modules and PV input connectors. Connect positive pole (+) to positive pole (+) of PV input connector, and negative pole (-) to negative pole (-) of PV input connector.
  3. Make sure the wires are securely connected.

3.7 Final Assembly

After connecting all wirings, replace the bottom cover by screwing the two screws back in place.

4. Operation

4.1 Power ON/OFF

Once the unit is properly installed and batteries are connected, simply press the On/Off switch (located on the bottom of the case) to turn on the unit.

4.2 Operation and Display Panel

The operation and display panel is on the front of the inverter. It includes three indicators, four function keys, and an LCD display, showing operating status and input/output power information.

Detailed view of the LCD display, LED indicators (AC/INV, CHG, FAULT), and function keys (ESC, UP, DOWN, ENTER).
Figure 5: LCD Display and Control Buttons
LED Indicator Messages
LED IndicatorColorMessages
AC/INVGreenSolid On: Output is powered by utility in Line mode.
Flashing: Output is powered by battery or PV in battery mode.
CHGGreenSolid On: Battery is fully charged.
Flashing: Battery is charging.
FAULTRedSolid On: Fault occurs in the inverter.
Flashing: Warning condition occurs in the inverter.
Function Keys
Function KeyDescription
ESCTo exit setting mode
UPTo go to previous selection
DOWNTo go to next selection
ENTERTo confirm the selection in setting mode or enter setting mode

4.3 LCD Display Icons

The LCD displays various information about the inverter's status and performance.

LCD Display Icons and Descriptions
IconFunction Description
ACIndicates the AC input.
PVIndicates the PV input.
INPUT/BATTERYIndicates input voltage, input frequency, PV voltage, battery voltage, and charger current.
Configuration ProgramIndicates the setting programs.
ERROR (flashing)Indicates warning condition with warning code.
ERROR (solid)Indicates fault condition with fault code.
OUTPUT/BATTERY/LOADIndicates output voltage, output frequency, load percent, load in VA, load in Watt, and discharging current.
Battery Level BarLeft side flashing bar and battery icon indicates battery level by 0-20%, 20-40%, 40-60%, and 80-100% in battery mode and charging status in line mode.
OVER LOADIndicates overload. Right side flashing bar and load icon indicates load level by 0-24%, 25-50%, 50-75%, and 75-100%.
Mains ConnectionIndicates unit connects to the mains.
PV ConnectionIndicates unit connects to the PV panel.
BYPASSIndicates load is supplied by utility power.
Utility ChargerIndicates the utility charger circuit is working.
DC/AC InverterIndicates the DC/AC inverter circuit is working.
MuteIndicates unit alarm is disabled.

4.4 LCD Setting

After pressing and holding the ENTER button for 3 seconds, the unit will enter setting mode. Use the “UP” or “DOWN” button to select setting programs, then press “ENTER” to confirm or “ESC” to exit.

Refer to the detailed tables in the PDF manual (pages 15-20) for a complete list of configurable settings, including output source priority, maximum charging current, AC input voltage range, power saving mode, battery type, auto restart options, output voltage, output frequency, utility charging current, and voltage points for SBU priority.

4.5 Lithium Battery Connection and Settings

If using lithium batteries, only those matched with the BMS communication protocol are allowed. Follow the battery connection steps in section 3.4. Additionally:

  1. Connect the RJ45 connector to the COMM port on the inverter.
  2. Connect the other end of the RJ45 plug to the battery communication port (RS485). Ensure RS485-A connects to RS485-A and RS485-B connects to RS485-B.

If choosing a lithium battery, connect the BMS communication cable between the battery and the inverter. Set the battery type to “Lib-485” in Program 5.

Communication Port Pin Definition
Pin NumberDefinition
1RX
2TX
3VCC
4VCC
5RS485-A
6RS485-B
7GND
8GND

When the battery type is set to “Lib-485”, settings for programs 12, 13, and 29 are adjusted. The default charging current is 0.5C. If communication fails, the inverter will cut off output. If the communication protocol does not match, you can select “LIB” mode.

After pressing and holding the “ESC” button for 3 seconds, you can enter the lithium battery information display page. This page shows total battery voltage, remaining capacity, charging/discharge current, BMS board temperature, and individual cell voltages/temperatures.

4.6 Display Setting

The LCD display information can be cycled by pressing the “UP” or “DOWN” key. Information displayed includes input voltage, input frequency, PV voltage, MPPT charging current, MPPT charging power, battery voltage, output voltage, output frequency, load percentage, load in VA, load in Watt, DC discharging current, and main CPU Version.

4.7 Operating Mode Description

The inverter operates in various modes depending on the power sources available and configured priorities.

Operating Mode Descriptions
Operation modeDescriptionLCD display
Standby mode / Power saving modeNo output is supplied by the unit but it still can charge batteries.No charging.
Line ModeThe unit will provide output power from the mains. It will also charge the battery at line mode.Charging by utility and PV energy.
Charging by utility.
Power from utility.
Battery ModeThe unit will provide output power from battery and PV power.Power from battery and PV energy.
Power from battery only.
Power from PV energy only.

4.8 Battery Equalization Description

Battery equalization is a function added to the charge controller to reverse the buildup of negative chemical effects like stratification and to remove sulfate crystals. This process helps maintain battery capacity and is recommended periodically.

How to Apply Equalization Function:

Enable battery equalization in monitoring LCD setting program 33. Then, apply this function by either:

  1. Setting the equalization interval in program 37.
  2. Activating equalization immediately in program 39.

When to Equalize:

In float stage, when the set equalization interval is reached, or equalization is active immediately, the controller will enter the Equalize stage.

Equalize Charging Time and Timeout:

In the Equalize stage, the controller supplies power to charge the battery until it reaches the battery equalization voltage. Constant-voltage regulation is then applied to maintain this voltage. The battery remains in the Equalize stage until the set battery equalized time is reached.

5. Troubleshooting

This section provides guidance for common issues, warning indicators, and fault codes. For persistent errors, contact a qualified service person or the service center.

5.1 Warning Indicator

The inverter provides audible alarms and flashing icons for various warning conditions.

Warning Indicators
Warning CodeWarning EventAudible AlarmIcon flashing
01Fan is locked when inverter is on.Beep twice every secondERROR icon
03Battery is over-chargedBeep twice every secondERROR icon
04Low batteryBeep twice every secondERROR icon
07OverloadBeep twice every secondOVER LOAD icon
10Output power deratingBeep twice every secondERROR icon
12Solar charger stops due to low battery.ERROR icon
13Solar charger stops due to high PV voltage.ERROR icon
14Solar charger stops due to overload.ERROR icon
15PV is weakERROR icon
61When the battery communication is abnormal, stop charging and discharging.ERROR icon

5.2 Fault Reference Code

Faults indicate more serious issues. The red fault indicator will be solid on, and a buzzer alarm will sound.

Fault Reference Codes
Fault CodeFault EventIcon on
01Fan is locked when inverter is off.ERROR icon
02Over temperatureERROR icon
03Battery voltage is too highERROR icon
04Battery voltage is too lowERROR icon
05Output short-circuited or over temperature is detected by internal converter components.ERROR icon
06Output voltage is too high.ERROR icon
07Overload time outERROR icon
08Bus voltage is too highERROR icon
09Bus soft start failedERROR icon
11Main relay failedERROR icon
51Over current or surgeERROR icon
52Bus voltage is too lowERROR icon
53Inverter soft start failedERROR icon
55Over DC voltage in AC outputERROR icon
56Battery connection is openERROR icon
57Current sensor failedERROR icon
58Output voltage is too lowERROR icon

5.3 Troubleshooting Table

Troubleshooting Guide
ProblemLCD/LED/BuzzerExplanation / Possible causeWhat to do
Unit shuts down automatically during startup process.LCD/LEDs and buzzer will be active for 3 seconds and then complete off.The battery voltage is too low (<1.91V/Cell)1. Re-charge battery.
2. Replace battery.
No response after power on.No indication.1. The battery voltage is far too low. (<1.4V/Cell)
2. Battery polarity is connected reversed.
1. Check if batteries and the wiring are connected well.
2. Re-charge battery.
3. Replace battery.
Mains exist but the unit works in battery mode.Input voltage is displayed as 0 on the LCD and green LED is flashing.Input protector is trippedCheck if AC breaker is tripped and AC wiring is connected well.
Green LED is flashing.Insufficient quality of AC power. (Shore or Generator)1. Check if AC wires are too thin and/or too long.
2. Check if generator (if applied) is working well or if input voltage range setting is correct. (UPS Appliance)
Green LED is flashing.Set "Solar First" as the priority of output source.Change output source priority to Utility first.
When the unit is turned on, internal relay is switched on and off repeatedly.LCD display and LEDs are flashingBattery is disconnected.Check if battery wires are connected well.
Fault code 07Overload error. The inverter is overload 110% and time is up.Reduce the connected load by switching off some equipment.
Fault code 05Output short circuited.Check if wiring is connected well and remove abnormal load.
Temperature of internal converter component is over 120°C.Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.
Buzzer beeps continuously and red LED is on.Fault code 02Internal temperature of inverter component is over 100°C.Return to repair center.
Fault code 03Battery is over-charged.Check if spec and quantity of batteries are meet requirements.
The battery voltage is too high.
Fault code 01Fan fault.Replace the fan.
Fault code 06/58Output abnormal (Inverter voltage below than 190Vac or is higher than 260Vac)1. Reduce the connected load.
2. Return to repair center
Fault code 08/09/53/57Internal components failed.Return to repair center.
Fault code 51Over current or surge.Restart the unit, if the error happens again, please return to repair center.
Fault code 52Bus voltage is too low.
Fault code 55Output voltage is unbalanced.
Fault code 56Battery is not connected well or fuse is burnt.If the battery is connected well, please return to repair center.

6. Specifications

6.1 Line Mode Specifications

Table 1: Line Mode Specifications
Parameter3.0KW/24V4.0KW/24V
Input Voltage WaveformSinusoidal (utility or generator)
Nominal Input Voltage120Vac
Low Loss Voltage95Vac±5V (UPS); 65Vac±7V (Appliances)
Low Loss Return Voltage100Vac±5V (UPS); 70Vac±5V (Appliances)
High Loss Voltage140Vac±5V
High Loss Return Voltage135Vac±5V
Max AC Input Voltage150Vac
Nominal Input Frequency50Hz / 60Hz (Configurable in program 09)
Low Loss Frequency45±1Hz/55±1Hz
Low Loss Return Frequency47±1Hz/57±1Hz
High Loss Frequency55±1Hz/65±1Hz
High Loss Return Frequency53±1Hz/63±1Hz
Output Short Circuit ProtectionLine mode: Circuit Breaker
Battery mode: Electronic Circuits
Efficiency (Line Mode)>95% (Rated R load, battery fully charged)
Transfer Time10ms typical (UPS); 20ms typical (Appliances)

6.2 Inverter Mode Specifications

Table 2: Inverter Mode Specifications
Parameter3.0KW/24V4.0KW/24V
Rated Output Power3.0KW4.0KW
Output Voltage WaveformPure Sine Wave
Output Voltage Regulation120Vac±5%
Output Frequency60Hz or 50Hz
Peak Efficiency94%
Overload Protection5s@≥150% load; 10s@110%~150% load
Surge Capacity2* rated power for 5 seconds
Nominal DC Input Voltage24Vdc
Cold Start Voltage23.0Vdc
Low DC Warning Voltage22.0Vdc
Low DC Warning Return Voltage23.0Vdc
Low DC Cut-off Voltage21.0Vdc
High DC Recovery Voltage29Vdc
High DC Cut-off Voltage31Vdc
No Load Power Consumption<35W

6.3 Charge Mode Specifications

Table 3: Charge Mode Specifications
Parameter3.0KW/24V4.0KW/24V
Utility Charging Mode
Charging Current (UPS) @ Nominal Input Voltage80A110A
Bulk Charging Voltage (Flooded Battery)29.2Vdc
Bulk Charging Voltage (AGM / Gel Battery)28.2Vdc
Floating Charging Voltage27Vdc
Charging Algorithm3-Step
Solar Charging Mode
Rated Power5600W
PV Charge Current100A140A
Efficiency98.0% max.
Max. PV Array Open Circuit Voltage350Vdc
PV Array MPPT Voltage Range55-350Vdc
Standby Power Consumption2W
Battery Voltage Accuracy+/-0.3%
PV Voltage Accuracy+/-2V
Charging Algorithm3-Step

6.4 General Specifications

Table 4: General Specifications
Parameter3.0KW/24V4.0KW/24V
Safety CertificationCE
Operating Temperature Range0°C to 55°C
Storage temperature-15°C~60°C
Dimension (D*W*H), mm400*250*89mm
Net Weight, kg7.5kg8.5kg

6.5 Approximate Back-up Time Table

Approximate Back-up Time Table (4.0KW Model)
Load (W)Backup Time @ 24Vdc 100Ah (min)Backup Time @ 24Vdc 200Ah (min)
3004491100
600222525
900124303
120095227
150068164
180056126
210048108
24003594
27003174
32002867

Note: Backup time depends on the quality, age, and type of battery. Specifications of batteries may vary depending on different manufacturers.

* Product technical specifications are subject to change without notice.

7. User Tips

  • Wi-Fi Monitoring: The inverter supports optional Wi-Fi monitoring. If you wish to use this feature, ensure you have the necessary Wi-Fi module and app for remote control and status checks.
  • Battery Compatibility: This inverter is compatible with various battery types including Flooded, Gel, Lithium-iron phosphate, Lithium-ion, AGM/Sealed, and user-customized batteries. Always select the correct battery type in the LCD settings for optimal performance and safety.
  • AC Input Voltage: The inverter is designed for 110/120V AC input. It does not accept 220V AC input. Ensure your AC source matches the specified voltage range.
  • System Sizing: To maximize operation, ensure your PV array power does not exceed 5600W and the MPPT voltage range is between 55-280VDC. Consult the PV Connection section for detailed panel wiring methods (series/parallel) and cable dimensions.
  • Weight: The 4.0KW model weighs approximately 8.5kg (18.7 lbs), while the 3.0KW model weighs 7.5kg (16.5 lbs). Consider this for mounting and handling.

8. Maintenance

Regular maintenance ensures the longevity and optimal performance of your inverter. Always disconnect all power sources (AC, DC, PV) before performing any maintenance.

  • Cleaning: Periodically clean the inverter's exterior to prevent dust buildup, especially around ventilation openings. Use a dry, soft cloth. Do not use liquid cleaners.
  • Connections: Regularly check all electrical connections (battery, AC input/output, PV input) for tightness and signs of corrosion. Re-tighten if necessary.
  • Ventilation: Ensure that the inverter's ventilation openings are clear and not obstructed. Adequate airflow is crucial for preventing overheating.
  • Battery Inspection: For lead-acid batteries, check electrolyte levels and terminal conditions as per battery manufacturer guidelines. For all battery types, monitor battery health and performance through the LCD display or optional Wi-Fi monitoring.
  • Firmware Updates: Check the manufacturer's website for any available firmware updates that may improve performance or add features.
  • Professional Inspection: It is recommended to have a qualified technician inspect the system annually to ensure all components are functioning correctly and safely.

9. Warranty and Support

This SUMRY inverter is designed for reliable operation. For specific warranty terms and conditions, please refer to the official documentation provided at the time of purchase or contact SUMRY customer support. Keep your purchase receipt as proof of purchase.

For technical support, troubleshooting assistance beyond this manual, or warranty claims, please contact your local dealer or the SUMRY service center. You may also refer to the full user manual PDF for more detailed information: View User Manual (PDF).

© 2024 SUMRY. All rights reserved.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.