SUMRY MPS-V MAX SERIES 10.2KW 48VDC

Contents

SUMRY MPS-V MAX SERIES 10.2KW 48VDC Hybrid Solar Inverter User Manual

Model: MPS-V MAX SERIES 10.2KW 48VDC

1. Introduction

This manual provides comprehensive instructions for the assembly, installation, operation, and troubleshooting of your SUMRY MPS-V MAX SERIES 10.2KW 48VDC Hybrid Solar Inverter. Please read this manual carefully before installation and operation, and keep it for future reference. This inverter/charger combines the functions of an inverter, solar charger, and battery charger to provide uninterruptible power support. Its user-friendly LCD display allows for configurable settings such as battery charging current, AC/solar charger priority, and acceptable input voltage for various applications.

1.1. Key Features

  • Pure sine wave inverter.
  • Configurable input voltage range for home appliances and personal computers via LCD setting.
  • Configurable battery charging current based on applications via LCD setting.
  • Configurable AC/Solar Charger priority via LCD setting.
  • Compatible with mains voltage or generator power.
  • Auto restart while AC is recovering.
  • Overload, over temperature, and short circuit protection.
  • Smart battery charger design for optimized battery performance.
  • Cold start function.
Pure Sine Wave Inverter features including 160A MPPT solar charger, high PV input voltage, dual output, WiFi/GPRS, and touch button.

Figure 1: Key Features of the SUMRY Hybrid Solar Inverter.

2. Safety Instructions

WARNING: This chapter contains important safety and operating instructions. Read and keep this manual for future reference.

  1. Before using the unit, read all instructions and cautionary markings on the unit, the batteries, and all appropriate sections of this manual.
  2. CAUTION: To reduce risk of injury, charge only deep-cycle lead-acid type rechargeable batteries. Other types of batteries may burst, causing personal injury and damage.
  3. Do not disassemble the unit. Take it to a qualified service center when service or repair is required. Incorrect re-assembly may result in a risk of electric shock or fire.
  4. To reduce risk of electric shock, disconnect all wirings before attempting any maintenance or cleaning. Turning off the unit will not reduce this risk.
  5. CAUTION: Only qualified personnel can install this device with battery.
  6. NEVER charge a frozen battery.
  7. For optimum operation of this inverter/charger, please follow required specifications to select appropriate cable size. It's very important to correctly operate this inverter/charger.
  8. Be very cautious when working with metal tools on or around batteries. A potential risk exists to drop a tool to spark or short circuit batteries or other electrical parts and could cause an explosion.
  9. Please strictly follow installation procedures when you want to disconnect AC or DC terminals. Please refer to the INSTALLATION section of this manual for details.
  10. One piece of 150A fuse is provided as over-current protection for the battery supply.
  11. GROUNDING INSTRUCTIONS: This inverter/charger should be connected to a permanent grounded wiring system. Be sure to comply with local requirements and regulations to install this inverter.
  12. NEVER cause AC output and DC input short circuited. Do NOT connect to the mains when DC input short circuits.
  13. Warning!! Only qualified service persons are able to service this device. If errors still persist after following troubleshooting table, please send this inverter/charger back to local dealer or service center for maintenance.
Diagram showing comprehensive protections including Overload, Overheating, High/Low Voltage, Battery, Short Circuit, Overcurrent, Anti Reverse, and Power Failure Protection.

Figure 2: Comprehensive Protection Features.

3. Product Overview

The SUMRY MPS-V MAX SERIES 10.2KW 48VDC Hybrid Solar Inverter is designed for robust performance in solar power systems. Below is a visual overview of the unit and its components.

Front and rear view of the SUMRY 10.2KW Hybrid Solar Inverter, highlighting the LCD display, function buttons, AC input, main output, second output, PV inputs, communication ports, and battery input.

Figure 3: Product Overview with labeled components.

3.1. Basic System Architecture

The inverter/charger can be integrated into a basic hybrid power system as shown below. This system typically includes solar power (PV modules), external battery packs, and can connect to a generator or utility grid to power various home appliances.

Basic System Architecture diagram showing connections between Solar Power, Batteries, Generator/Utility, the Solar Inverter, and AC Loads (Household, Office, Industrial Equipment).

Figure 4: Hybrid Power System Architecture.

3.2. Dimensions

The dimensions of the inverter are D*W*H 537*390*130 (mm).

Diagram showing the dimensions of the inverter: Length 537mm, Width 390mm, Height 130mm. Also highlights the touch button and dual output ports (Main Out, Second Out).

Figure 5: Inverter Dimensions and Dual Output.

3.3. Appliance Compatibility

This inverter is capable of powering a wide range of appliances in both home and office environments, including various motor-type appliances.

Images of various appliances including an induction cooker, pressure cooker, air conditioner, refrigerator, sealing machine, air compressor, chainsaw, hammer drill, angle grinder, and fan, indicating the inverter's compatibility.

Figure 6: Appliance Compatibility.

3.4. Usage Scenarios

The inverter provides reliable power for various scenarios, ensuring your home, office, and RV equipment remain operational even during power outages.

Images depicting the inverter powering home devices when the power is off, and powering office and RV equipment, showcasing its versatility.

Figure 7: Inverter Usage Scenarios.

4. Installation

4.1. Unpacking and Inspection

Before installation, please inspect the unit. Be sure that nothing inside the package is damaged. You should have received the following items:

  • User manual x 1
  • Ring terminal x 1
  • MC4 terminal head x 2

4.2. Preparation

Before connecting all lines, remove the screws under the machine and remove the bottom cover plate.

4.3. Mounting the Unit

Consider the following points before selecting where to install:

  • Do not mount the inverter on flammable construction materials.
  • Mount on a solid surface.
  • Install this inverter at eye level in order to allow the LCD display to be read at all times.
  • Proper air circulation to dissipate heat, allow a clearance of approx. 20 cm to the side and approx. 50 cm above and below the unit.
  • The ambient temperature should be between 0°C and 55°C to ensure optimal operation.
  • The recommended installation position is to be adhered to the wall vertically.
  • Make sure that other objects and surfaces are left with enough space from the machine to ensure adequate heat dissipation and that there is enough room to remove the wires.

SUITABLE FOR MOUNTING ON CONCRETE OR OTHER NON-COMBUSTIBLE SURFACE ONLY.

Install the unit by screwing two screws. It's recommended to use M4 or M5 screws.

4.4. Battery Connection

CAUTION: For safety operation and regulation compliance, it's requested to install a separate DC over-current protector or disconnect device between battery and inverter. It may not be requested to have a disconnect device in some applications, however, it's still requested to have over-current protection installed. Please refer to typical amperage in below table as required fuse or breaker size.

ModelWire SizeCable (mm²)Torque Value (max)
8.2KW/10.2KW1 x 2AWG252 Nm

Follow these steps to implement battery connection:

  1. Remove insulation sleeve 18 mm for positive and negative conductors.
  2. Suggest to put bootlace ferrules on the end of positive and negative wires with a proper crimping tool.
  3. Connect all battery packs as shown in the diagram below.
  4. Insert the battery wires flatly into battery connectors of inverter and make sure the bolts are tightened with a torque of 2 Nm in clockwise direction. Make sure polarity at both the battery and the inverter/charge is correctly connected and conductors are tightly screwed into the battery terminals. Recommended tool: #2 Pozi Screwdriver.
Diagram showing how to connect multiple 12V batteries in series to the inverter (8.2KW/10.2KW model) to achieve 48VDC.

Figure 8: Battery Connection Diagram.

WARNING: Shock Hazard! Installation must be performed with care due to high battery voltage in series.

CAUTION!! Before making the final DC connection or closing DC breaker/disconnector, be sure positive (+) must be connected to positive (+) and negative (-) must be connected to negative (-).

Video 1: Unboxing and Connection Demonstration.

4.5. AC Input/Output Connection

CAUTION!! Before connecting to AC input power source, please install a separate AC breaker between inverter and AC input power source. This will ensure the inverter can be securely disconnected during maintenance and fully protected from over current of AC input. The recommended specification of AC breaker is 63A for 8.2KW/10.2KW.

CAUTION!! There are two terminal blocks with “IN” and “OUT” markings. Please do NOT mis-connect input and output connectors.

WARNING! All wiring must be performed by a qualified personnel.

WARNING! It's very important for system safety and efficient operation to use appropriate cable for AC input connection. To reduce risk of injury, please use the proper recommended cable size as below.

ModelGaugeCable (mm²)Torque Value
8.2KW/10.2KW10 AWG61.2 Nm

Follow these steps to implement AC input/output connection:

  1. Before making AC input/output connection, be sure to open DC protector or disconnector first.
  2. Remove insulation sleeve 10mm for six conductors. And shorten phase L and neutral conductor N 3 mm.
  3. Insert AC input wires according to polarities indicated on terminal block and tighten the terminal screws. Be sure to connect PE protective conductor (⍃) first.
    • Ground (yellow-green)
    • L → LINE (brown or black)
    • N → Neutral (blue)
Detailed diagram of the inverter's rear panel showing AC IN, MAIN OUT, SECOND OUT, PV1, PV2, COMM, and BATTERY terminals. It illustrates the wiring connections for AC input and output.

Figure 9: AC Input/Output Wiring Diagram.

WARNING: Be sure that AC power source is disconnected before attempting to hardwire it to the unit.

  1. Then, insert AC output wires according to polarities indicated on terminal block and tighten terminal screws.
    • L → LINE (brown or black)
    • N → Neutral (blue)
  2. Make sure the wires are securely connected.

4.6. PV Connection

CAUTION: Before connecting to PV modules, please install separately a DC circuit breaker between inverter and PV modules.

WARNING! It's very important for system safety and efficient operation to use appropriate cable for PV module connection. To reduce risk of injury, please use the proper recommended cable size as below.

ModelWire SizeCable (mm²)Torque Value (max)
8.2KW/10.2KW1 x 10AWG61.2 Nm

PV Module Selection

When selecting proper PV modules, please be sure to consider below parameters:

  1. Open circuit Voltage (Voc) of PV modules not exceeding max. PV array open circuit voltage of inverter.
  2. Open circuit Voltage (Voc) of PV modules should be higher than min. battery voltage.
INVERTER MODEL8.2KW/10.2KW
Max. PV Array Open Circuit Voltage500Vdc
PV Array MPPT Voltage Range90Vdc~450Vdc

Take 250Wp PV module as an example. After considering above two parameters, the recommended module configurations are listed as below table:

Solar Panel Spec. (reference)SOLAR INPUT (Min in serial: 6 pcs, max. in serial: 13 pcs)Q'ty of panelsTotal input power
250Wp, Vmp: 30.1Vdc, Imp: 8.3A, Voc: 37.7Vdc, Isc: 8.4A, Cells: 606 pcs in serial6 pcs1500W
8 pcs in serial8 pcs2000W
12 pcs in serial12 pcs3000W
13 pcs in serial13 pcs3250W
12 pieces in serial and 3 sets in parallel36 pcs8200W
10 pieces in serial and 4 sets in parallel40 pcs10200W

PV Module Wire Connection

Step 1: Check the input voltage of PV array modules. The acceptable input voltage of the inverter is 90VDC-500VDC. Please make sure that the maximum current load of each PV input connector is 18A.

CAUTION: Exceeding the maximum input voltage can destroy the unit!! Check the system before wire connection.

Step 2: Disconnect the DC circuit breaker.

Step 3: Assemble provided PV connectors with PV modules by following the steps below:

Components for PV connectors and Tools:
  • Female connector housing
  • Female terminal
  • Male connector housing
  • Male terminal
  • Crimping tool and spanner
Cable preparation and connector assembly process:

Strip one cable 8 mm on both end sides and be careful NOT to nick conductors.

Insert striped cable into female terminal and crimp female terminal. Insert assembled cable into female connector housing. Insert striped cable into male terminal and crimp male terminal. Insert assembled cable into male connector housing.

Then, use spanner to screw pressure dome tightly to female connector and male connector. Check correct polarity of connection cable from PV modules and PV input connectors. Connect positive pole (+) of connection cable to positive pole (+) of PV input connector. Connect negative pole (-) of connection cable to negative pole (-) of PV input connector.

Diagram illustrating the PV connector assembly process, showing how to strip cables, crimp terminals, and insert them into connector housings for both positive and negative connections.

Figure 10: PV Connector Assembly and Wiring.

4.7. Final Assembly

After connecting all wirings, please put bottom cover back by screwing two screws.

4.8. Communication Connection

Wi-Fi cloud communication (option):

Please use supplied communication cable to connect to inverter and Wi-Fi module. Download APP and installed from APP store, and Refer to "Wi-Fi Plug Quick Installation Guideline" to set up network and registering. The inverter status would be shown by mobile phone APP or webpage of computer.

GPRS cloud communication (option):

Please use supplied communication cable to connect to inverter and GPRS module, and then applied external power to GPRS module. Download APP and installed from APP store, and Refer to "GPRS RTU Quick Installation Guideline" to set up network and registering. The inverter status would be shown by mobile phone APP or webpage of computer.

Battery communication:

The communication between the battery and the inverter can be realized through the battery communication interface, so that the inverter and the lithium battery can exchange information (Baud rate: 9600).

Lithium battery and inverter connection:

Use power cables, communication cables for lithium batteries, and inverters to connect.

Note: Lithium battery and inverter positive and negative positions, check the correct installation; The RJ45 connector of the communication cable connects to the BMS port of the inverter, and the other RJ45 connector connects to the RS485 port of the lithium battery; Before connecting, make sure that the lithium battery and inverter are turned off. (It is recommended to install a circuit breaker for the power cables of the lithium battery and the inverter battery interface. Otherwise, a spark may occur.)

Diagram showing the optional WiFi/GPRS communication module connected to the inverter for monitoring and control via a smartphone app.

Figure 11: Monitoring and Control via Smart App (Optional).

The lithium battery communication cable interface is shown in the figure below:

CONNECTION METHODA-01A-02
17
28
EMPTY PIN IS NOT CONNECTED

In order to communicate with the lithium battery BMS, you should press the “ENTER” button for a long time, and set the battery type as “LIB-485” in program 05. Then select the matching battery protocol in Program 43.

5. Operation

5.1. Power ON/OFF

Once the unit has been properly installed and the batteries are connected well, simply press the On/Off switch (located on the button of the case) to turn on the unit.

5.2. Operation and Display Panel

The operation and display panel, shown below, is on the front panel of the inverter. It includes three indicators, four function keys, and an LCD display, indicating the operating status and input/output power information.

LCD Display and Function Buttons with LED Indicator table. The table describes LED indicators (INV/AC, CHG, FAULT) and their messages (Solid On, Flashing), and Function Keys (ESC, UP, DOWN, ENTER) with their descriptions.

Figure 12: LCD Display, Indicators, and Function Keys.

LED IndicatorMessages
INV/AC (Green Solid On)Output is powered by utility in Line mode.
INV/AC (Green Flashing)Output is powered by battery or PV in battery mode.
CHG (Green Solid On)Battery is fully charged.
CHG (Green Flashing)Battery is charging.
FAULT (Red Solid On)Fault occurs in the inverter.
FAULT (Red Flashing)Warning condition occurs in the inverter.
Function KeyDescription
ESCTo exit setting mode
UPTo go to previous selection
DOWNTo go to next selection
ENTERTo confirm the selection in setting mode or enter setting mode

5.3. LCD Display Icons

The LCD display provides various icons to indicate the inverter's status and information.

IconFunction description
⍃Indicates the AC input.
☀Indicates the PV input.
8.8.8 KW V Hz AIndicate input voltage, input frequency, PV voltage, charger current (if PV in charging for 10.2KW models), charger power, battery voltage.
(8.8.8)Indicates the setting programs.
⚠Indicates the warning and fault codes.
8.8.8 KW VA %Indicate output voltage, output frequency, load percent, load in VA, load in Watt and discharging current.
⚛Indicates overload.
⚡Indicates unit connects to the mains.
☀Indicates unit connects to the PV panel.
AC BYPASSIndicates load is supplied by utility power.
⚡Indicates the utility charger circuit is working.
⚡Indicates the DC/AC inverter circuit is working.
🔇Indicates unit alarm is disabled.

5.4. LCD Setting

After pressing and holding the ENTER button for 3 seconds, the unit will enter setting mode. Use the "UP" or "DOWN" buttons to select setting programs, then press "ENTER" to confirm or "ESC" to exit.

Key configurable settings include:

  • Program 00: Exit setting mode (00 GOE for one-button restore, 00 GOH for exit).
  • Program 01: Output source priority (Utility first, Solar first, SBU priority, MKS priority).
  • Program 02: Maximum charging current (Configurable from 10A to 160A).
  • Program 03: AC input voltage range (Appliances: 90-280VAC, UPS: 170-280VAC).
  • Program 05: Battery type (AGM, Flooded, LIB, User-Defined, LIB-485).
  • Program 06: Auto restart when overload occurs (Restart disable/enable).
  • Program 07: Auto restart when over temperature occurs (Restart disable/enable).
  • Program 09: Output frequency (50Hz/60Hz).
  • Program 10: Output voltage (220V/230V/240V).
  • Program 11: Maximum utility charging current (Configurable).
  • Program 12: Setting voltage point back to utility source (Configurable from 42V to 58V).
  • Program 13: Setting voltage point back to battery mode (Configurable from 48V to 58V).
  • Program 16: Charger source priority (Solar first, Solar and Utility, Only Solar).
  • Program 18: Alarm control (Alarm on/off).
  • Program 19: Auto return to default display screen (Return to default/Stay at latest screen).
  • Program 20: Backlight control (Backlight on/off).
  • Program 22: Beeps while primary source is interrupted (Alarm on/off).
  • Program 23: Overload bypass (Bypass disable/enable).
  • Program 25: Record fault code (Record enable/disable).
  • Program 26: Bulk charging voltage (C.V voltage) (Configurable from 48.0V to 61.0V).
  • Program 27: Floating charging voltage (Configurable from 48.0V to 61.0V).
  • Program 29: Low DC cut-off voltage (Configurable from 48.0V to 61.0V).
  • Program 30: Battery equalization (Enable/Disable).
  • Program 31: Battery equalization voltage (Configurable from 40.0V to 61.0V).
  • Program 33: Battery equalized time (Configurable from 5min to 900min).
  • Program 34: Battery equalized timeout (Configurable from 5min to 900min).
  • Program 35: Equalization interval (Configurable from 1 to 90 days).
  • Program 36: Equalization activated immediately (Enable/Disable).
  • Program 37: GRID-tie operation (Off grid, Hybrid).
  • Program 38: GRID-tie current (Configurable).
  • Program 39: Led pattern light (Led pattern off/on).
  • Program 41: Dual output (L2F/L20).
  • Program 42: Enter the dual output functional voltage point (Configurable from 40.0V to 52.0V).
  • Program 43: Lithium battery protocol (PYLON/PACE).
  • Program 44: Delayed grid access (Disable/Enable).
  • Program 45: Maximum Second Load (20%~70%).

5.5. Display Setting

The LCD display information can be switched in turns by pressing the “UP” or “DOWN" key. The selectable information includes: input voltage, input frequency, PV voltage, charging current, charging power, battery voltage, output voltage, output frequency, load percentage, load in Watt, load in VA, load in Watt, DC discharging current, and main CPU Version.

5.6. Operating Mode Description

The inverter supports various operating modes to suit different power requirements.

Standby Mode / Power Saving Mode

In standby mode, the inverter is not turned on yet but can charge the battery without AC output. In power saving mode, if enabled, the inverter's output will be off when the connected load is very low or not detected.

Line Mode

In Line Mode, the unit provides output power from the mains and charges the battery. This mode can also involve PV and mains charging, or mains charging only.

Grid-Tie Operation

When operating in Grid-Tie mode, the display will flash every 3 seconds.

Battery Mode

In Battery Mode, the unit provides output power from the battery and can also combine with solar power to supply loads.

5.7. Battery Equalization Description

Battery equalization reverses the buildup of negative chemical effects like stratification and helps remove sulfate crystals, which can reduce battery capacity. It is recommended to equalize the battery periodically.

How to Apply Equalization Function

Enable battery equalization in monitoring LCD setting program 30. Then, apply this function by either:

  • Setting equalization interval in program 35.
  • Activating equalization immediately in program 36.

When to Equalize

In the float stage, when the setting equalization interval is reached, or equalization is activated immediately, the controller will enter the Equalize stage.

Equalize Charging Time and Timeout

In the Equalize stage, the controller charges the battery until it reaches the battery equalization voltage. Constant-voltage regulation maintains this voltage until the set equalized time is reached. If the battery voltage is still lower than the equalization voltage after the timeout, the charge controller will extend the equalized time. If the voltage remains low after the extended time, the controller stops equalization and returns to float stage.

5.8. Mains and Lithium Battery Activation Function

  1. After 90s of mains power connection to the inverter, the machine is connected to the mains and starts to work.
  2. If the inverter is in lithium battery mode (item 05 is LIB or LIB-485), and the battery is not connected after mains connection, the mains activation function is automatically enabled.

6. Clearance and Maintenance for Anti-Dust Kit

6.1. Overview

Every inverter is already installed with an anti-dust kit from the factory. The inverter will automatically detect this kit and activate an internal thermal sensor to adjust internal temperature. This kit also keeps dust from your inverter and increases product reliability in harsh environments.

6.2. Clearance and Maintenance

Step 1: Loosen the screw in a counterclockwise direction on the top of the inverter.

Diagram showing the top of the inverter with a screw indicated for loosening to access the anti-dust kit.

Figure 13: Loosening the Anti-Dust Kit Screw.

Step 2: Then, the dustproof case can be removed, and the air filter foam taken out as shown below.

Diagram showing the removal of the dustproof case and air filter foam from the inverter.

Figure 14: Removing Dustproof Case and Air Filter Foam.

Step 3: Clean the air filter foam and dustproof case. After cleaning, re-assemble the dust-kit back to the inverter.

NOTICE: The anti-dust kit should be cleaned from dust every one month.

7. Troubleshooting

Refer to the table below for common issues and their solutions. If problems persist, contact qualified service personnel.

ProblemLCD/LED/BuzzerExplanation / Possible causeWhat to do
Unit shuts down automatically during startup process.LCD/LEDs and buzzer will be active for 3 seconds and then complete off.The battery voltage is too low (<1.91V/Cell)1. Re-charge battery.
2. Replace battery.
No response after power on.No indication.1. The battery voltage is far too low. (<1.4V/Cell)
2. Internal fuse tripped.
1. Contact repair center for replacing the fuse.
2. Re-charge battery.
3. Replace battery.
Input voltage is displayed as 0 on the LCD and green LED is flashing.Input protector is trippedCheck if AC breaker is tripped and AC wiring is connected well.
Mains exist but the unit works in battery mode.Green LED is flashing.Insufficient quality of AC power. (Shore or Generator)1. Check if AC wires are too thin and/or too long.
2. Check if generator (if applied) is working well or if input voltage range setting is correct. (UPS Appliance)
Green LED is flashing.Set "Solar First" as the priority of output source.Change output source priority to Utility first.
When the unit is turned on, internal relay is switched on and off repeatedly.LCD display and LEDs are flashingBattery is disconnected.Check if battery wires are connected well.
Fault code 07Overload error. The inverter is overload 110% and time is up.Reduce the connected load by switching off some equipment.
Output short circuited.Check if wiring is connected well and remove abnormal load.
Fault code 05Temperature of internal converter component is over 120°C.Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.
Fault code 02Internal temperature of inverter component is over 100°C.Return to repair center.
Buzzer beeps continuously and red LED is on.Fault code 03Battery is over-charged.Check if spec and quantity of batteries are meet requirements.
Fault code 01The battery voltage is too high.Replace the fan.
Fault code 06/58Fan fault1. Reduce the connected load.
2. Return to repair center.
Fault code 08/09/53/57Output abnormal (Inverter voltage below than 190Vac or is higher than 260Vac)Return to repair center.
Fault code 51Internal components failed.Restart the unit, if the error happens again, please return to repair center.
Fault code 52Over current or surge.
Fault code 55Bus voltage is too low.
Output voltage is unbalanced.

8. Specifications

Detailed technical specifications for the SUMRY MPS-V MAX SERIES 10.2KW 48VDC Hybrid Solar Inverter are provided in the tables below.

8.1. Line Mode Specifications

INVERTER MODEL8.2KW10.2KW
Input Voltage WaveformSinusoidal (utility or generator)
Nominal Input Voltage230Vac
Low Loss Voltage170Vac±7V (UPS); 90Vac±7V (Appliances)
Low Loss Return Voltage180Vac±7V (UPS); 100Vac±7V (Appliances)
High Loss Voltage280Vac±7V
High Loss Return Voltage270Vac±7V
Max AC Input Voltage300Vac
Nominal Input Frequency50Hz / 60Hz (Auto detection)
Low Loss Frequency40±1Hz
Low Loss Return Frequency42±1Hz
High Loss Frequency65±1Hz
High Loss Return Frequency63±1Hz
Output Short Circuit ProtectionCircuit Breaker
Efficiency (Line Mode)>95% (Rated R load, battery full charged)
Transfer Time10ms typical (UPS); 20ms typical (Appliances)

8.2. Inverter Mode Specifications

INVERTER MODEL8.2KW10.2KW
Rated Output Power8.2KW10.2KW
Output Voltage WaveformPure Sine Wave
Output Voltage Regulation230Vac±5%
Output Frequency50Hz
Peak Efficiency93%
Overload Protection3s@≥150% load; 5s@101%~150% load
Surge Capacity2* rated power for 5 seconds
Nominal DC Input Voltage48Vdc
Cold Start Voltage46.0Vdc
Low DC Warning Voltage @load < 50%44.0Vdc
Low DC Warning Voltage @load ≥ 50%42.0Vdc
Low DC Warning Return Voltage @load < 50%45.0Vdc
Low DC Warning Return Voltage @load ≥ 50%44.0Vdc
Low DC Cut-off Voltage @load < 50%41.0Vdc
Low DC Cut-off Voltage @load ≥ 50%40.0Vdc
High DC Recovery Voltage62Vdc
High DC Cut-off Voltage63Vdc
No Load Power Consumption70W75W

8.3. Two Load Output Power

INVERTER MODEL8.2KW10.2KW
Full Load8200W10200W
Maximum Main Load8200W10200W
Second Load Range1640W~5740W2040W~7140W
Main Load Cut Off Voltage52VDC
Main Load Return Voltage54VDC

8.4. Charge Mode Specifications

Utility Charging Mode8.2KW10.2KW
Charging Algorithm3-Step
AC Charging Current (Max)140Amp140Amp
Bulk Charging - Flooded Battery58.4
Bulk Charging - AGM / Gel Battery56.4
Floating Charging Voltage54Vdc

8.5. MPPT Solar Charging Mode

INVERTER MODEL8.2KW10.2KW
Max. PV Array PowerPV1 Channel: 5400WPV1 Channel: 5400W
PV2 Channel: 5400WPV2 Channel: 5400W
Imax.PVPV1 Channel:18APV1 Channel:18A
PV2 Channel:18APV2 Channel:18A
Nominal PV Voltage360Vdc
PV Array MPPT Voltage Range90Vdc~450Vdc
Max. PV Array Open Circuit Voltage500Vdc
Max Charging Current (AC charger plus solar charger)160Amp

8.6. Grid-Tie Operation

INVERTER MODEL8.2KW10.2KW
Nominal Output Voltage220/230/240VAC
Feed in Grid Voltage Range190~253VAC
Feed in Grid Frequency Range50~1Hz/60~1Hz
Nominal Output Current35.8A44.3A
Power Factor Range>0.99
Maximum Conversion Efficiency98%

8.7. General Specifications

INVERTER MODEL8.2KW10.2KW
Safety CertificationCE
Operating Temperature Range-10°C to 50°C
Storage Temperature-15°C to 60°C
Humidity5% to 95% Relative Humidity (non-condensing)
Dimension (D*W*H), mm550*390*130mm
Net Weight, kg14.514.7

8.8. Approximate Back-up Time Table

The table below provides approximate backup times for different loads and battery capacities. Note that actual backup time depends on battery quality, age, and type.

ModelLoad (W)Backup Time @ 48Vdc 100Ah (min)Backup Time @ 48Vdc 200Ah (min)
8.2KW/10.2KW5006131288
1000268613
1500158402
2000111271
250090215
320076182
350065141
400050112
450044100
50004090
62003680
72003270
82002860
92002450
102002040

9. User Tips

  • This inverter supports dual output voltages, typically 110V and 220V, making it versatile for various household and office appliances.
  • When connecting to a two-phase system, ensure proper wiring for phase, phase, and neutral connections as per local electrical codes.
  • While the inverter can operate in certain modes without a battery, for full hybrid functionality and backup power, a compatible battery system is required.

10. Support and Further Information

For detailed diagrams, advanced settings, and comprehensive troubleshooting, please refer to the complete user manual PDF available at: SUMRY 8.2KW/10.2KW Hybrid Solar Inverter User Manual (PDF).

If you encounter issues not covered in this manual or require further assistance, please contact your local dealer or the SUMRY Global Store customer support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.