intelamp YL002-12A

Contents

Intelamp Outdoor Solar Light Instruction Manual

Model: YL002-12A (Variants: YL002-12A1PK, YL002-12B, YL002-12C)

Brand: intelamp

1. Introduction

This manual provides essential information for the safe and efficient operation of your Intelamp Outdoor Solar Light. Please read it thoroughly before installation and use. This product is designed to provide reliable, energy-efficient lighting for various outdoor spaces.

2. Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Keep the device and its cord out of reach of children under 3 years old.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • This product has an IP65 protection level, meaning it is protected against dust and low-pressure water jets. However, avoid submerging it in water.

WARNING: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. For disposal, please check your local authority's website for more information and dispose of the lithium-ion battery safely in accordance with the applicable legal requirements.

3. Product Overview

Key Features:

  • Wide Arc Lighting Area: 270° wide-angle illumination with 3 adjustable lamp heads.
  • High-Efficiency Solar Panels: Features a 40 square inch solar panel for efficient charging.
  • High-Capacity Batteries: Equipped with a 6000mAh Lithium Iron Phosphate battery, offering extended lighting duration.
  • Unique 2 Sensor Design: Dual motion sensors provide a full 180° security coverage, reducing blind spots.
  • Easy Installation: Comes with screws and tie straps for versatile mounting options.
  • Durable: IP65 waterproof rating ensures reliable performance in various weather conditions.
  • 3 Lighting Modes: Offers flexible lighting options to suit different needs.

Components:

The Intelamp Outdoor Solar Light consists of a solar panel, a central light unit with two motion sensors, and two adjustable side light panels, all integrated into a single unit.

Intelamp solar light with 3 adjustable heads and solar panel

Figure 1: Intelamp Outdoor Solar Light

IP65 Waterproof, 1200LM High bright, 270° wide-angle lighting

Figure 2: IP65 Waterproof and Wide-Angle Lighting

Comparison of 2 sensors (180° detection, 25ft/7.6m * 2 operation range) vs 1 sensor (90° detection, 25ft/7.6m operation range)

Figure 3: Dual Motion Sensor Detection Range

Comparison of charging/lighting times (4hrs charge/24hrs lighting vs 5hrs charge/36hrs lighting)

Figure 4: Charging and Lighting Duration

4. Specifications

AttributeValue
Model NumberYL002-12A (YL002-12A1PK)
Brand Nameintelamp
Power SourceSOLAR
Voltage5V
Light SourceLED bulbs
Is DimmableYes
Solar Cell TypeLithium battery
Protection LevelIP65
Body MaterialABS
UseIndustrial (Outdoor Security)
Warranty1 year
Installation MethodSelf-contained
Is Batteries IncludedYes
Is Bulbs IncludedYes
Battery Capacity6000mAh
Brightness1200 lumens
Solar Panel Size40 square inches
Package Length26 cm
Package Width15 cm
Package Height13 cm
Package Weight0.976 kg

5. Setup

5.1. Preparation

  1. Before first use, remove all protective films from the solar light casing and solar panel.
  2. Ensure the solar panel is unobstructed and free of stains for optimal charging.

5.2. Installation

Install or place the light fixture in a well-lit, unobstructed location where it can receive direct sunlight for most of the day. The recommended installation height is 1.8-2.5 meters.

Product dimensions: 9.4in x 4.3in solar panel, 12in light width

Figure 5: Product Dimensions

Mounting Methods:

  • Screw Fixation: The light can be screwed to hard surfaces such as walls, wooden fences, and garage door frames.
  • Cable Tie Fixation: The light can be bound to trees or posts using the provided tie straps.
Example of light on a fence with screw fixation

Figure 6: Installation using Screw Fixation

Example of light on a tree with cable tie fixation

Figure 7: Installation using Cable Ties

Adjustable Design:

The light features an adjustable design to optimize lighting and charging.

  • The middle lamp head can be adjusted vertically (up and down) by 45 degrees.
  • The side lamp heads can be adjusted horizontally (left to right) by up to 90 degrees.
  • The solar panel can be adjusted vertically (up and down) by 60 degrees. The optimum tilt angle is usually 20 degrees to make the most efficient use of available sunlight and to allow rainwater to remove any dust build-up efficiently.
Adjustable and Flexible Design (solar panel 60°, side lights 90°, middle light 45°)

Figure 8: Adjustable Design

6. Operating Instructions

6.1. Power On

Locate the power switch on the side/bottom of the light fixture. Switch it to the "ON" position to turn it on. Some models support a light-controlled mode; switch it to the "Auto" position, and the light fixture will automatically turn on after dark and automatically turn off at dawn.

6.2. Charging

No manual charging is required. The solar panel will automatically absorb sunlight and store electrical energy. Place the light fixture in direct sunlight. 6-8 hours of sufficient sunlight can provide 8-12 hours of nighttime lighting (actual duration depends on weather and sunlight intensity).

6.3. Lighting Modes

The solar motion light has 3 lighting modes. A short press of the "MODE" button cycles through these modes:

  1. Mode 1 (Sensor with Low Brightness): Lights are set on low brightness at all times and will illuminate brightly when motion is detected.
  2. Mode 2 (Sensor Only): Lights will be off and will illuminate brightly when motion is detected. The light turns off after a 30-second delay when no one is around, making it more energy-efficient.
  3. Mode 3 (Constant Low Brightness): Lights will be on low light throughout the night, and the motion sensor is inactivated.
Sensor Mode (high brightness then low brightness then off) vs ON Mode (keep lighting all the time)

Figure 9: Lighting Modes

6.4. Product Demonstration Video

Video 1: Product features and motion sensor demonstration.

7. Maintenance

  • Cleaning: Regularly clean the solar panel to ensure it is free of dust, dirt, and debris. A clean panel ensures optimal sunlight absorption and charging efficiency.
  • Storage: If storing the light for an extended period, turn it off and store it in a dry place, away from direct sunlight and out of reach of children.
  • Inspection: Periodically inspect the light for any signs of damage. Do not use if the product is damaged.

8. Troubleshooting

  • Light not turning on:
    - Ensure the power switch is in the "ON" or "Auto" position.
    - Verify the solar panel is receiving sufficient direct sunlight for charging (6-8 hours recommended).
    - Check for any obstructions blocking the solar panel.
  • Light not detecting motion:
    - Ensure the light is set to Mode 1 or Mode 2 (motion sensor active modes).
    - Check the sensor area for any obstructions.
    - The dual sensors provide a 180° detection range; ensure movement occurs within this range.
  • Short lighting duration:
    - The solar panel may not be receiving enough direct sunlight for a full charge. Relocate the light or clear obstructions.
    - The solar panel might be dirty; clean it regularly.
    - Extreme weather conditions (e.g., prolonged cloudy or rainy days) can affect charging and battery performance.

9. User Tips

  • The 6000mAh battery provides extended lighting, often lasting well beyond a single night, especially in sensor modes.
  • For models with a detachable solar panel (e.g., YL002-12B), consider installing the panel in a separate, sunnier location for optimal charging.
  • Utilize the adjustable lamp heads to direct light precisely where needed, maximizing coverage and effectiveness.
  • If your model includes a remote control (e.g., YL002-12B, YL002-12C), use it to easily switch between lighting modes after installation, especially in hard-to-reach areas.
  • The dual motion sensors offer a wide 180° detection angle, effectively covering large areas.
  • The light is highly effective for illuminating areas within 2-3 meters for security and visibility.

10. Warranty & Support

10.1. Warranty

This product comes with a 1-year warranty from the date of purchase. Please retain your proof of purchase for any warranty claims.

10.2. Further Documentation

A detailed user manual in PDF format is available for download. You can view it here: User Manual (PDF)

10.3. Contact Information

  • Manufacturer: Shenzhen Jindian Electronic Technology Co., Ltd.
    No. 9, Tianyang 1st Road, Datianyang Industrial Zone, Dongfang Community, Songgang Street, Bao'an District, Shenzhen City, Guangdong Province
    Email: service@intelamp.com
  • EU Authorized Representative: SUCCESS COURIER SL
    CALLE RIO TORMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3, Fuenlabrada, Madrid, 28947 Spain
    Email: successservice2@hotmail.com

11. Compliance Information

This product must comply with all applicable safety and regulatory requirements in the market where it is sold. Our company has assessed the requirements and regulations applicable to this product based on its actual product type, function, and target market. The product meets the testing requirements of Shenzhen BCTC.

CE Mark

CE Marking


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.