NEWBOLER Bicycle Front Light User Manual

1. Introduction

The NEWBOLER Bicycle Front Light is designed to provide powerful illumination for your cycling adventures. Featuring a durable aluminum alloy body, multiple lighting modes, and a high-capacity battery (LIG003 model), it ensures visibility and safety on the road or trail. The LIG003 model also includes a convenient power bank function for charging other devices.

2. Safety Information

• Do not look directly into the light beam to avoid eye injury.
• Keep the device away from children.
• Ensure the light is securely mounted before riding.
• While the light is waterproof for daily use (IPX6/IP65), avoid prolonged submersion in water.
• Do not disassemble or modify the light, as this may void the warranty and pose a safety risk.
• Use only the provided or recommended charging cables and adapters.

3. Package Contents

Please check the package for the following items:

• NEWBOLER Bicycle Front Light (LIG003 or LIG013 model)
• Handlebar Mounting Bracket(s) (Normal or Extend, quantity may vary by model)
• USB Type-C Charging Cable
• User Manual (this document)

4. Specifications

4.1. Model: LIG003 (14000mAh, 4500LM)

Figure 1: LIG003 Product Information and Dimensions

Figure 2: LIG003 Light Modes and Runtimes

4.2. Model: LIG013 (2000mAh, 3000LM)

Figure 3: LIG013 Model Overview

5. Setup and Installation

Your NEWBOLER Bicycle Front Light comes with mounting brackets for easy installation on your bicycle handlebar. There are two main types of brackets: Normal and Extend. The installation process is similar for both.

5.1. LIG003 Model Installation (Double Aluminum Alloy Brackets)

1. Step 1: Place the base of the bracket over your bicycle handlebar. If needed, use spacers to ensure a snug fit.
2. Step 2: Adjust the position of the base and tighten the base screws to secure it.
3. Step 3: Install the first two brackets onto the base in the same manner, ensuring they are firmly attached.
4. Step 4: Carefully push the bicycle light into place on the secured base. Ensure it slides fully into the mounting slot.
5. Step 5: Tighten the screws on the light's base to fix it securely to the bracket.
6. Step 6: Verify that the light is stable and does not wobble.

Figure 4: LIG003 Installation Steps

Figure 5: LIG003 Double Aluminum Alloy Brackets

5.2. LIG013 Model Installation (Single Bracket)

1. Step 1: Position the bracket on your bicycle handlebar at the desired location.
2. Step 2: Insert the screw through the bracket and manually tighten it to secure the bracket to the handlebar.
3. Step 3: Slide the bottom of the bicycle light into the bracket along the slide rail until it clicks into place.
4. Step 4: Tighten any additional bottom screws to ensure the light is firmly attached to the bracket.
5. Step 5: Confirm that the installation is complete and the light is stable.

Figure 6: LIG013 Installation Steps

Figure 7: Bracket Types

6. Operating Instructions

6.1. Power On/Off and Mode Selection

• Power On: Press and hold the power button (usually marked with a power symbol) for a few seconds until the light turns on.
• Change Modes: Short press the power button to cycle through the available lighting modes (e.g., Floodlight, Spotlight, High Light, Flash for LIG003; Low Beam, High Beam On, High Beam Full Beam, Flashing for LIG013).
• Power Off: Press and hold the power button again for a few seconds until the light turns off.

Figure 8: LIG003 Light with Data Display and Mode Button

6.2. Charging the Light

The light is equipped with a Type-C charging port.

1. Connect the provided USB Type-C cable to the charging port on the light.
2. Connect the other end of the cable to a suitable USB power source (e.g., wall adapter, computer USB port).
3. The display (LIG003) or indicator light will show the charging status.
4. Charge until the battery indicator shows full (approx. 8 hours for LIG003, 2-4 hours for LIG013).

6.3. Power Bank Function (LIG003 Model Only)

The LIG003 model can be used as a power bank to charge other USB-powered devices.

1. Ensure the bicycle light has sufficient charge.
2. Connect your device's charging cable to the Type-C port on the bicycle light.
3. The light will begin charging your device. The battery power display (0-100) will show the remaining charge.

Figure 9: LIG003 Power Bank Function

Figure 10: LIG003 Battery Features

7. Maintenance

• Cleaning: Wipe the light with a soft, damp cloth. Do not use abrasive cleaners or solvents.
• Storage: Store the light in a cool, dry place when not in use. If storing for an extended period, charge the battery to about 50% every 3-6 months to prolong battery life.
• Waterproofing: While waterproof, avoid direct high-pressure water jets on the charging port or buttons. Ensure the charging port cover (if present) is securely closed.
• Impact Resistance: The aluminum alloy shell is designed to be compression and drop resistant, but avoid severe impacts to prevent damage to internal components.

Figure 11: Daily Life Waterproofing

Figure 12: Strong Aluminum Alloy Shell

8. Troubleshooting

9. User Tips

• For optimal visibility during day and night, use the flashing mode during the day and a steady high-lumen mode at night.
• Regularly check the battery level, especially before long rides, to avoid running out of light.
• When using the power bank function (LIG003), monitor the light's battery level to ensure you have enough power for your ride.
• Adjust the light's angle to illuminate the road ahead without blinding oncoming traffic or pedestrians.

10. Warranty and Support

NEWBOLER products are manufactured to high-quality standards. For warranty information or technical support, please refer to the seller's policies or contact NEWBOLER Official Store directly. Keep your purchase receipt as proof of purchase.