JIKONG JK BMS 3.2/4.3 LCD Monitor

Contents

JIKONG BMS 3.2/4.3 inch Screen Display User Manual

Intelligent Battery Level Indicator for JIKONG BMS Systems

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your JIKONG BMS 3.2-inch and 4.3-inch LCD screen displays. Please read this manual thoroughly before use to ensure proper functionality and safety.

2. Setup

2.1 Unpacking

Carefully remove the display and its accessories from the packaging. Ensure all components are present:

  • JIKONG BMS Display (3.2-inch or 4.3-inch)
  • Connection Cable
  • Mounting accessories (if included with your model)

An example of the packaged 3.2-inch display and accessories:

JIKONG 3.2-inch display in box with accessories

Image: JIKONG 3.2-inch display and accessories as received in packaging.

2.2 Physical Dimensions

Refer to the diagrams below for the physical dimensions of the display units.

3.2-inch Display Dimensions

JIKONG 3.2-inch display rear view with dimensions

Image: Rear view of the 3.2-inch display showing dimensions (100.50mm x 61.50mm x 11.50mm).

4.3-inch Display Dimensions

JIKONG 4.3-inch touch screen display rear view with dimensions

Image: Rear view of the 4.3-inch display showing dimensions (129.4mm x 82mm).

2.3 External Interfaces and Cable Connection

The display connects to the JIKONG BMS via a dedicated cable. The user interface port is used for power supply and serial port signal connection.

  • Socket Type: GH1.25MM-6P, vertical plug-in.
  • Cable Length: Typically 400mm (for 3.2-inch display) or 50mm (for 4.3-inch display). Longer cables may be available.

Pin Definition:

Pin NumberPin NamePin Description
1K-Activation switch
2K+Activation switch
3GNDPower supply ground
4RS-485B485 signal B
5RS-485A485 signal A
6VCCPower Supply Voltage

Connect the provided cable to the '用户接口' (User Interface) port on the back of the display and to the corresponding port on your JIKONG BMS. Ensure the connection is secure.

JIKONG 3.2-inch display with connection cable and power button

Image: 3.2-inch display showing the connection cable and power button.

JIKONG 4.3-inch display connected to a BMS via UART connector

Image: 4.3-inch display connected to a JIKONG V19 PB Serial BMS via UART connector.

3. Operating Instructions

3.1 Turning On/Off

To turn the display on or off, long press the button located on the right side of the display unit.

3.2 Display Appearance and Information

The display provides real-time information about your battery management system. The 3.2-inch display typically shows the following:

JIKONG 3.2-inch display with labeled components

Image: JIKONG 3.2-inch display with key information areas labeled.

  1. MOS Temp: Temperature of the MOSFETs.
  2. SOC (%): State of Charge, indicating the battery's current charge level.
  3. Battery Pack Total Voltage (V): The overall voltage of the battery pack.
  4. Output Current (A): The current being drawn from or supplied to the battery.
  5. Fault Code (ERR): Displays error codes if any issues are detected.
  6. Average Voltage (V): The average voltage across the battery cells.

The 4.3-inch touch screen display offers a more detailed interface:

JIKONG 4.3-inch touch screen display

Image: JIKONG 4.3-inch touch screen display showing various battery parameters.

3.3 Language Selection

The 4.3-inch display supports multiple languages including Chinese, English, Thai, and Vietnamese. Language settings can typically be accessed through the display's menu interface.

3.4 Viewing Cell Information

On the 4.3-inch touch screen display, you can check individual cell pack information, including voltage and status.

JIKONG 4.3-inch touch screen display showing cell pack information

Image: 4.3-inch display showing detailed information for each battery cell.

JIKONG 4.3-inch touch screen display showing individual battery voltage

Image: 4.3-inch display showing individual battery voltages for multiple cells.

3.5 Setting RS485 and CANBUS

The 4.3-inch display allows you to set up RS485 and CANBUS protocols directly from the display interface.

JIKONG 4.3-inch touch screen display showing RS485 and CANBUS settings

Image: 4.3-inch display showing options for RS485 and CANBUS protocol settings.

4. Maintenance

To ensure the longevity and optimal performance of your JIKONG BMS display, follow these maintenance guidelines:

  • Keep the display clean using a soft, dry cloth. Avoid abrasive cleaners or solvents.
  • Ensure the display is not exposed to extreme temperatures or direct sunlight for prolonged periods.
  • Regularly check cable connections for any signs of wear or damage.
  • For detailed maintenance procedures, please refer to the official JIKONG '3.2 Inch Display Use the Maintenance Manual' PDF document, which can be found at JIKONG 3.2 Inch Display Maintenance Manual (PDF).

5. Troubleshooting

If you encounter issues with your JIKONG BMS display, consider the following:

  • No Display/Power: Check all cable connections to ensure they are secure. Verify the power supply voltage is within the specified range (9-12V).
  • Incorrect Readings: Ensure the display is correctly connected to the BMS and that the BMS itself is functioning properly.
  • Warning Information: The display may show warning messages for various conditions, such as over-temperature protection. Address the underlying issue indicated by the warning.
JIKONG 4.3-inch touch screen display showing warning information

Image: 4.3-inch display showing a 'CHARGE OVER TEMPERATURE PROTECTION' warning.

User Tips

  • The 4.3-inch display models are touch-sensitive, allowing for intuitive navigation and control.
  • Ensure compatibility: The V19 display is specifically for JIKONG V19 BMS firmware versions. The classic 4.3 LCD display is compatible with JIKONG BMS firmware versions V15 to V19.

6. Specifications

6.1 General Parameters

ParameterValue (3.2-inch)Value (4.3-inch)
Display CategoryLCDTFT
Size3.2 inch4.3 inch
ResolutionN/A480*272
Operating Temperature-20°C to +70°C-20°C to +70°C
Storage Temperature-30°C to +85°C-30°C to +80°C

6.2 Power Supply Voltage

ParameterLeast ValueRepresentative ValueCrest Value
Service Voltage (V)91112

6.3 Working Environment and Reliability Parameters

ParameterTesting EnvironmentLeast ValueRepresentative ValueCrest Value
Working Temperature (°C)At 12V, humidity 60%-202570
Storage Temperature (°C)---302580
Working Humidity (PH)25°C10%60%90%

6.4 Key Features and Certifications

  • Balance Function: Active Balanced BMS
  • Type: LIFEPO4 Battery BMS
  • Charge and Discharge Port: Common Port BMS
  • Functions: Overcharge Protection, Over Discharge Protection, Overcurrent Protection, Short Circuit Protection
  • Usage Scenario: Power BMS, Energy Storage BMS, 3C Digital BMS
  • Certifications: CE, FCC, RoHS, UL

7. Warranty and Support

JIKONG products are designed for reliability and performance. For any technical assistance or support, please refer to the official JIKONG documentation or contact your vendor. Specific warranty details may vary by region and purchase point; please consult your purchase agreement for more information.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.