OBDOK CTB007 PRO

Contents

WOYO CTB007 PRO ECU Testing OBD2 Breakout Box Instruction Manual

Model: CTB007 PRO

1. Introduction

The WOYO CTB007 PRO is a professional OBD-II breakout box and ECU testing tool designed for comprehensive automotive diagnostics, development, and bench testing. It provides convenient access to all OBD-II pins, monitors live voltages with true RMS, offers optional CAN termination, and facilitates safe and fast hookup of other diagnostic and programming devices. This manual provides essential information for the safe and effective use of your device.

2. Important Safety Notes

  • This device is intended for professional use only. Incorrect pin bridging or inappropriate termination can lead to damage of ECUs or vehicle wiring.
  • Pins 3/11 are OEM-defined; only use the MS-CAN terminator when the vehicle explicitly implements CAN on these pins.
  • The real-time voltage display provides a quick health check and should not be considered a replacement for an oscilloscope for detailed waveform analysis.

3. Features

  • 12 V / 24 V Compatible Circuit Tester: Robust design suitable for passenger cars and commercial vehicles.
  • Real-time OBD-II Pin Voltage Monitor (VRMS / true RMS): Monitors power/ground integrity (e.g., pin 16 (+B) and pins 4/5 (grounds)) and bus activity on CAN / K-Line. A green background indicates dynamic values.
  • 120 Ω CAN Termination Switches: Inserts a 120 Ω resistor across the CAN pair to compensate for missing termination during single-ECU or small bench networks, improving signal integrity and reducing reflections. Supports HS-CAN (pins 6 ↔ 14) and OEM/MS-CAN (pins 3 ↔ 11, vehicle-dependent).
  • Bench Testing Support: Provides convenient connectivity for IGN/START activation or external wake-up tools, allowing ECUs to be powered and exercised on the bench.
  • Signal Status Indication: Pin background flashing green indicates a dynamic signal.
  • High/Low Voltage Audible Alarms: Alerts for low voltage (< 11.8 V for 12V systems, < 23.6 V for 24V systems) with a slow beep, and high voltage (> 15.5 V for 12V systems, > 31 V for 24V systems) with a fast beep.
  • Ground Status Indication: Pins 4 or 5 display 'OPEN' when no ground is detected, and 'GND' when a valid ground is present.
  • Quick Jumper Function (Technician Use Only): Allows trained technicians to momentarily bridge selected OBD pins via current-limited paths for OEM-approved procedures.
  • Battery Replacement Memory Saver: Maintains vehicle power (12 V/24 V) during battery changes to preserve vehicle settings.
  • Convenient Connectivity: Features a 70 cm or 150 cm extension lead for rapid hookup to other diagnostic/programming tools. Supports 1mm/2mm/4mm banana plugs.

4. Specifications

AttributeValue
Input Voltage9.0-32.0VDC
Maximum Load2.0A
Resolution0.1V
Probes Socket16P*2.0mm
Overload ProtectionYes, PTC Fuse (Self-Healing)
Reverse Polarity ProtectionYes
Protocol StandardPWM(J1850), VPW(J1850), ISO 9141-2, DIS/ISO 14230-4, CAN(J-2284)
Operating Temperature-20℃-85℃, Humidity<70%
Banana Socket2mm*10; 2mm to 4mm*2
OBD Cable Length70cm (27.5inch) / 150cm (59inch)
Power Cable Connector5.5×2.1 mm
Item Weight0.4kg
External Testing CertificationCE
Software UpdateNo
ElectronicNo
Wireless SupportNo
Is Batteries IncludedNo
High-concerned chemicalNone

5. Setup

5.1 Powering the Device

The WOYO CTB007 PRO requires an external power input of 9–32 V DC via a 5.5 × 2.1 mm barrel connector. Ensure the selected voltage (12 V or 24 V) matches the vehicle battery or the module under test.

5.2 Connecting for ECU Bench Testing

For testing an ECU on a bench, connect the CTB007 PRO to the ECU and a 9V-32V DC power supply (12V 5.5*2.1mm). This setup provides convenient connectivity for IGN/START activation or external wake-up tools, allowing ECUs to be powered and exercised outside the vehicle.

Diagram showing WOYO CTB007 PRO connected to an ECU on a bench with a power supply and diagnostic tools.
Figure 1: ECU Bench Testing Setup

5.3 Battery Replacement Memory Saver Setup

The CTB007 PRO can be used to maintain vehicle power during battery changes, preserving ECU data and settings. Follow these steps:

  1. Close the car and ensure the ignition key is off.
  2. Connect the CTB007 PRO to a 12V/24V power supply (either DC 12V 5.5*2.1mm or directly to battery PIN 5 & PIN16).
  3. Power the car via the OBDII plug using the CTB007 PRO to save ECU data.
  4. Proceed to replace the old battery with a new one.
Diagram illustrating the steps for using the CTB007 PRO as a battery replacement memory saver.
Figure 2: Battery Replacement Memory Saver Connection

6. Operating Instructions

6.1 OBD2 Diagnosis

Connect the CTB007 PRO to your vehicle's OBD2 port. It is suitable for OBD2/OBD1 systems (using an OBD2 to OBD1 adapter if necessary) and supports cars, trucks, and motorcycles. It is not suitable for Tesla vehicles. The device can be connected to a diagnostic scanner or PC software for comprehensive vehicle analysis.

Image showing the CTB007 PRO connected to a car's OBD2 port and a multimeter.
Figure 3: OBD2 Diagnosis Connection

6.2 Real-time Pin Voltage Monitoring

The integrated LCD displays real-time VRMS data directly for each pin. This allows for quick checks of power/ground integrity and bus activity. A green background on the display indicates a dynamic signal.

Close-up of the CTB007 PRO LCD showing real-time voltage and current readings.
Figure 4: Real-time Voltage Display

6.3 CAN Termination Switches

The device features 120 Ω CAN termination switches to compensate for missing termination in single-ECU or small bench networks. This improves signal integrity and reduces reflections.

  • HS-CAN: Use for pins 6 ↔ 14 (standard).
  • OEM/MS-CAN: Use for pins 3 ↔ 11 (if present and vehicle-dependent).

Important: Use termination only for bench testing or scenarios with missing terminators. Keep the switches OFF during normal vehicle use to avoid over-termination.

Diagram showing the CAN termination switches and their corresponding pins.
Figure 5: CAN Termination Switches

6.4 Ground Status Indication

The device can detect the vehicle's ground signal on pins 4 and 5. If the ground is normal, it will display 'GND'. If no ground is detected, it will display 'OPEN'.

Diagram showing the CTB007 PRO detecting ground signal on pins 4 and 5, displaying GND or OPEN.
Figure 6: Ground Status Detection

6.5 Using with Multimeter/Oscilloscope

The CTB007 PRO supports 1mm/2mm/4mm banana plugs, allowing you to connect a multimeter or oscilloscope to test more data from the 16 OBD-II pins for advanced diagnostics.

Diagram showing the CTB007 PRO connected to a car, power, and a multimeter/oscilloscope.
Figure 7: Connecting to External Test Equipment

6.6 Operational Video

Watch this video for a demonstration of a similar WOYO EPS Tester, illustrating the general testing process and device interaction:

Video 1: WOYO PL118 EPS Tester Demonstration (illustrative of general testing process)

7. Maintenance

  • Keep the device clean and free from dust and moisture. Use a soft, dry cloth for cleaning.
  • Store the CTB007 PRO in a cool, dry place when not in use.
  • Avoid dropping the device or subjecting it to strong impacts.
  • Regularly inspect cables and connectors for any signs of wear or damage. Replace if necessary.

8. Troubleshooting

  • No Power/Display: Ensure the external power supply is correctly connected and provides the correct voltage (9-32V DC). Check the power cable connector (5.5x2.1mm).
  • 'OPEN' displayed for Ground Pins (4 or 5): Verify the vehicle's ground connection. If testing on a bench, ensure the ECU has a proper ground connection.
  • Audible Alarms (High/Low Voltage): Check the vehicle's battery voltage or the external power supply. Address any voltage irregularities before proceeding with diagnostics.
  • Unstable Signal Readings: Ensure all connections are secure. If using CAN termination, verify it's applied correctly for the specific scenario (bench testing, missing terminator). Avoid over-termination.

9. User Tips

  • Always refer to the vehicle's specific service manual for accurate pin assignments and diagnostic procedures.
  • When using the device for ECU bench testing, ensure the ECU is properly secured and all connections are stable.
  • For advanced diagnostics, utilize the banana plug connections to integrate with multimeters or oscilloscopes for more detailed signal analysis.
  • Keep the device's firmware updated (if applicable, though this model states 'No Software Update' in specifications, general advice for similar tools).

10. Warranty and Support

For detailed warranty information and technical support, please refer to the official user manual PDF or contact the manufacturer directly.

A comprehensive user manual (PDF) is available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.