Introduction
Thank you for choosing the Weikav MAX102 Mechanical Keyboard Kit. This high-performance keyboard kit features a durable aluminum alloy construction, tri-mode connectivity (2.4G wireless, Bluetooth, wired), hot-swappable switches, a large 10000mAh battery, and customizable RGB lighting. This manual provides detailed instructions for setting up, operating, and maintaining your keyboard to ensure optimal performance and longevity.
Package Contents
Please check the package for the following items:
- Weikav MAX102 Mechanical Keyboard Kit (unassembled, without keycaps and switches)
- 2-in-1 Key Puller
- USB Cable
- User Manual (this document)
- Warranty Card
Note: Keycaps and switches are for display purposes only and are not included with the kit unless specified by your retailer.
Setup Guide
1. Assembly (if applicable)
The MAX102 is a keyboard kit, meaning it typically requires assembly of switches and keycaps. Ensure you have compatible 3-pin or 5-pin hot-swappable mechanical switches and keycaps.
- Carefully align each switch with the hot-swap socket on the PCB and press firmly until it clicks into place. Ensure the pins are straight to avoid bending.
- Once all switches are installed, place the desired keycaps onto the switches.
2. Initial Charging
Before first use, it is recommended to fully charge the keyboard. Connect the provided USB cable to the keyboard's USB-C port and to a power source (e.g., computer USB port or USB wall adapter). The charging indicator (if present) will show charging status.
3. Connectivity Modes
The MAX102 supports three connection modes: 2.4G Wireless, Bluetooth, and Wired USB-C.
Switching Modes:
The tri-mode switch is discreetly located below the TAB key. To access it, gently lift the keycap above the switch. Toggle the switch to the desired position (ON/OFF for wireless modes).
2.4G Wireless Mode:
- Ensure the keyboard's mode switch is set to wireless (ON).
- Press FN + R to activate 2.4G mode.
- Retrieve the 2.4G USB receiver from its storage compartment on the back of the keyboard.
- Plug the USB receiver into an available USB port on your computer. The keyboard should connect automatically.
Bluetooth Mode:
The keyboard can pair with up to 3 Bluetooth devices.
- Ensure the keyboard's mode switch is set to wireless (ON).
- Press FN + Q, FN + W, or FN + E to select a Bluetooth channel. The corresponding key will flash, indicating pairing mode.
- On your device (computer, tablet, phone), search for Bluetooth devices and select "Weikav MAX102" (or similar) to pair.
- Once paired, the key will stop flashing and remain lit.
- To switch between paired Bluetooth devices, press FN + Q/W/E for the desired channel.
Wired Mode:
- Connect the USB-C cable to the keyboard and to your computer.
- Press FN + T to activate wired mode.
- The keyboard will function as a standard wired keyboard.
Operating Instructions
1. Lighting Control
The MAX102 features 16 million color RGB ARGB lighting with various effects and geometric decorative lights.
- Adjust Light Effect Modes: Press FN + ~ (tilde) key to cycle through different light effect modes (e.g., constant on, breathing, off).
- Adjust Single-Color Lighting: Press FN + Key (specific key not detailed, typically arrow keys or dedicated lighting keys) to adjust single-color lighting. Available colors include yellow, light blue, purple, white, blue, red, green.
2. Key Customization (QMK/VIA)
The MAX102 fully supports QMK and VIA, allowing for easy programming of each key and open-source firmware customization. This enables layout customization, quick shortcuts, and other feature modifications.
- Driver Software: The keyboard uses a self-developed web page-driven driver and VIA key modification software.
- Web Version Driver: Access the web-based driver at https://weikavmax102.hsgaming.cn/ for advanced customization.
3. Magnetic Quick Release
The keyboard features an innovative magnetic contact pin design for quick release and connection, enhancing stability and ease of disassembly.
Maintenance
1. Cleaning
- Use a soft, dry cloth to wipe the surface of the keyboard.
- For deeper cleaning, use the provided key puller to remove keycaps. A can of compressed air can be used to remove dust and debris from between switches.
- Keycaps can be cleaned with mild soap and water, then thoroughly dried before reattaching.
- Avoid using harsh chemicals or abrasive materials that could damage the aluminum alloy finish or keycap legends.
2. Hot-Swappable Switches
The MAX102 supports hot-swappable switches, allowing you to change switches without soldering. Use the provided switch puller to carefully remove switches. When inserting new switches, ensure the pins are aligned correctly with the PCB sockets to prevent damage.
Troubleshooting
- Keyboard not responding:
- Check the battery level and charge the keyboard if necessary.
- Ensure the correct connection mode (2.4G, Bluetooth, or Wired) is selected.
- For 2.4G, ensure the USB receiver is securely plugged in.
- For Bluetooth, re-pair the device if connection is lost.
- Try connecting via wired mode to rule out wireless issues.
- Keys not registering or double-typing:
- This could indicate a faulty switch. Since the keyboard is hot-swappable, try replacing the problematic switch.
- Ensure switches are fully seated in their sockets.
- Lighting issues:
- Ensure the keyboard is powered on.
- Cycle through lighting modes using FN + ~.
- Check the driver software for lighting settings.
- Customization software (VIA/QMK) not detecting keyboard:
- Ensure the keyboard is connected via wired mode.
- Verify that the correct firmware is installed and the software is up to date.
- Refer to the official QMK/VIA documentation or the provided web driver link for specific instructions.
Specifications
| Feature | Detail |
|---|---|
| Product Name | Vega MAX-102 3-Mode Aluminum Mechanical Keyboard |
| Color Options | Black Anode, Anode Red, Anode Silver, Electrophoretic Powder (Pink), Electrophoresis Milky White |
| Technology | 220 mesh anodized / 220-mesh electrophoresis |
| Shell Material | National standard 6063 aluminum alloy |
| Magnetic Contact Pin | 8PIN gold-plated Magnetic Pogo Pins + Ball Locks Quick Release |
| Structure | PCB - Particle GASKET Structure |
| Decorative Part | Back: Metal Brushed Backplate (Sand Gold + Gunmetal Gray), Anodized Storage Compartment Cover Plate; Positive: Plated Decorative Parts |
| Lighting | 16 million color RGB ARGB lights |
| Light Strip Features | Front electroplated decorative light strip, side geometric decorative lights |
| Positioning Plate | FR4 positioning plate |
| PCB | 1.2MM Single-Key Slot Black Core PCB |
| Open Source QMK/VIA | Supports QMK/VIA tri-mode |
| Battery Capacity | 10000mAh large capacity battery |
| Five-Layer Padding | PO sandwich cotton + PO axis lower pad + PET voice pad + PO axis seat cotton + PET insulating pad |
| Accessories | 2-in-1 key puller, USB cable, user manual, warranty card |
| Driver | Self-developed web page-driven + VIA key modification |
| Size | Length 400mm * Width 130.5mm * Front height 29mm * Rear height 40mm |
| Package Weight | Kit ~ 2100g, Final product ~ 2230g |
| Full Size Keyboard | Yes |
| Wrist Support | No |
| Battery Included | Yes |
| Operation Style | Mechanical |
| Language | English |
| Keyboard Standard | 100 Keys |
| Application | Desktop, Laptop |
| Type | 2.4Ghz Wireless |
| Brand Name | Ajazz |
| Origin | Mainland China |
User Tips
- Optimize Battery Life: To maximize the 10000mAh battery life, consider turning off RGB lighting when not needed, especially during wireless use.
- Experiment with Switches: Take advantage of the hot-swappable design to try different switch types (linear, tactile, clicky) to find your preferred typing experience.
- Customization Depth: Explore the QMK/VIA software to fully customize key assignments, macros, and lighting effects to suit your workflow or gaming style.
- Secure Wireless Connection: For critical tasks or gaming, the 2.4G wireless mode generally offers lower latency than Bluetooth.
Warranty and Support
The Weikav MAX102 Mechanical Keyboard Kit comes with a warranty as detailed on the included warranty card. For technical support, troubleshooting assistance, or warranty claims, please contact your retailer or the manufacturer directly. Keep your purchase receipt and warranty card for future reference.
