1. Introduction
The WOYO CTB007 PRO is a professional 12V/24V circuit-test and signal-access tool designed for automotive diagnostics, development, and bench testing. This device allows users to expose every OBD-II pin, monitor live voltages (true RMS), provide optional CAN termination, and safely and quickly connect other diagnostic or programming devices. It is an essential tool for technicians working with passenger cars and commercial vehicles.
2. Key Features
- 12V / 24V Compatible Circuit Tester: Robust design suitable for both passenger cars and commercial vehicles.
- Real-time OBD-II Pin Voltage Monitor (VRMS / true RMS): Monitors power/ground integrity (e.g., pin 16 (+B) and pins 4/5 (grounds)) and bus activity on CAN / K-Line. A green background on the LCD indicates dynamic values, signifying active signals.
- 120 Ω CAN Termination Switches: Inserts a 120 Ω resistor across the CAN pair to compensate for missing termination during single-ECU or small bench networks, improving signal integrity and reducing reflections. Supports HS-CAN (pins 6 ↔ 14) and OEM/MS-CAN (pins 3 ↔ 11, vehicle-dependent).
- Bench Testing Support: Provides convenient connectivity for IGN/START activation or external wake-up tools, enabling ECUs to be powered and exercised on the bench.
- High/Low Voltage Audible Alarms: Alerts users to voltage anomalies. Slow beep for low voltage (< 11.8 V for 12V systems, < 23.6 V for 24V systems) and fast beep for high voltage (> 15.5 V for 12V systems, > 31 V for 24V systems).
- Ground Status Indication: Pins 4 or 5 display "OPEN" when no ground is detected and "GND" when a valid ground is present.
- Quick Jumper Function: Allows trained technicians to momentarily bridge selected OBD pins via current-limited paths for OEM-approved procedures.
- Battery Replacement Memory Saver: Maintains vehicle power (12V/24V) during battery changes to preserve vehicle settings.
- Convenient Connectivity: Features a 70 cm or 150 cm extension lead for rapid hookup to other diagnostic/programming tools and an external power input (9–32 V DC, barrel 5.5 × 2.1 mm).
3. Package Contents
The WOYO CTB007 PRO package includes the following components:
- WOYO CTB007 PRO OBD2 Breakout Box Unit
- 2mm to 4mm Banana Adapter Plugs (2 pieces)
- Optional: CTBC001 ECU Breakout Leads (included if "and Cable" model is selected)
4. Setup Instructions
Follow these steps to set up your WOYO CTB007 PRO for various diagnostic tasks:
- Connecting to Vehicle OBD2 Port:
Locate your vehicle's OBD2 port (typically under the dashboard). Plug the CTB007 PRO's OBD2 connector into the vehicle's port. The device will power on automatically.
Image: CTB007 PRO connected to a car's OBD2 port for diagnosis, compatible with OBD2/OBD1 systems (excluding Tesla).
- ECU Bench Testing Setup (with optional CTBC001 ECU breakout leads):
For bench testing, connect the CTB007 PRO to the ECU using the CTBC001 breakout leads. Ensure proper pin connections according to the ECU's wiring diagram. Provide external power (9-32V DC) to the CTB007 PRO via the barrel connector.
Image: Setup for ECU testing on a bench, demonstrating connection of the CTB007 PRO to an ECU using breakout leads and a scanner/code reader.
- Battery Replacement Memory Saver Setup:
To use the memory saver function, connect the CTB007 PRO to a 12V/24V power supply (e.g., another vehicle battery or a power adapter) via the external power input. Then, connect the CTB007 PRO to the vehicle's OBD2 port before disconnecting the vehicle's main battery. This maintains power to the ECU.
Image: Diagram illustrating the Battery Replacement Memory Saver function, showing how to connect the CTB007 PRO to a 12V/24V power supply to maintain ECU data during battery changes.
5. Operating Instructions
The WOYO CTB007 PRO offers several diagnostic capabilities:
5.1. Reading Real-time VRMS Data
Once connected, the LCD display will show the real-time VRMS (true RMS) values for each of the 16 OBD-II pins. If a pin detects a pulse or waveform signal, its background color will flash green, indicating a dynamic signal.

Image: Close-up of the Digital LCD Display showing real-time VRMS readings for OBD-II pins. It also highlights the PIN 16 High/Low Voltage Audible Alarms with specific voltage thresholds for 12V and 24V systems.
5.2. Using 120 Ω CAN Termination Switches
The CTB007 PRO features switches to activate a 120 Ω resistor across specific CAN pairs. This is useful for bench testing single ECUs or small networks where termination might be missing. Ensure these switches are OFF during normal vehicle use to prevent over-termination.
- HS-CAN: Use the switch for pins 6 ↔ 14.
- OEM/MS-CAN: Use the switch for pins 3 ↔ 11 (check vehicle specifications for applicability).

Image: Detailed view of the 120 Ω CAN Termination Switches, explaining how to activate the 120 Ω resistor for HS-CAN and OEM/MS-CAN.
5.3. Ground Signal Detection
The display for pins 4 and 5 will show "GND" if a valid ground signal is detected, and "OPEN" if no ground is present. This helps quickly verify ground integrity.
5.4. Using with External Diagnostic Tools
The CTB007 PRO can be used in conjunction with multimeters, oscilloscopes, or diagnostic scanners/code readers for more in-depth analysis. Simply connect your external tool to the appropriate banana sockets on the CTB007 PRO.

Image: Illustration of using the CTB007 PRO with a multimeter or oscilloscope to test various OBD-II pins, showing the versatility of the breakout box for detailed signal analysis.
5.5. Quick Jumper Function (Technician Use Only)
This function allows a trained technician to temporarily bridge selected OBD pins. This should only be used for OEM-approved procedures (e.g., make-specific communication or synchronization tasks) and with extreme caution to avoid damage to ECUs or wiring.
5.6. Product Demonstration Video
Video: This demonstration showcases the WOYO CTB007 PRO in action, including unboxing, connecting to an OBD2 port, viewing VRMS data on the LCD, testing CAN lines, ECU bench testing with breakout leads, and highlighting its reverse polarity protection.
6. Maintenance
- Cleaning: Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Storage: Store the CTB007 PRO in a cool, dry place away from direct sunlight and extreme temperatures.
- Overload Protection: The device is equipped with a self-healing PTC fuse for overload protection. In case of an overload, the fuse will temporarily open and reset once the fault is cleared.
- Cable Care: The PET braided tube cable is robust and durable. Avoid sharp bends or excessive pulling to prolong its lifespan.

Image: Features of the PET Braided Tube Cable, emphasizing its robust, durable, insulating, temperature-resistant, and flexible properties.
7. Troubleshooting
- Device Not Powering On: Ensure the OBD2 connector is securely plugged into the vehicle's port or that external power is correctly supplied (for bench testing). Check the vehicle's battery voltage.
- Incorrect VRMS Readings: Verify all connections are secure. Ensure the vehicle's ignition is on (if required for specific signals). If using external tools, confirm their proper functioning.
- No Dynamic Signal Indication (Green Flash): Check if the vehicle system or ECU is active and generating signals on the tested pins.
- Audible Alarms Triggering: If high or low voltage alarms sound, immediately check the vehicle's battery voltage and the integrity of the power supply to the OBD2 port.
- Reverse Polarity Protection: The CTB007 PRO features reverse polarity protection. If positive and negative connections are accidentally mixed, the device will not be damaged, preventing PCB burn-out.
8. User Tips
- Always refer to your vehicle's service manual for specific pinout diagrams and diagnostic procedures.
- When performing ECU bench testing, double-check all connections to avoid accidental short circuits or incorrect voltage application.
- The real-time voltage display is a quick check; for detailed waveform analysis, an oscilloscope is recommended.
9. Specifications
| Attribute | Value |
|---|---|
| Model Name | CTB007 PRO |
| Input Voltage | 9.0-32.0VDC |
| Maximum Load | 2.0A |
| Resolution | 0.1V |
| Overload Protection | Yes, PTC Fuse (Self-Healing) |
| Reverse Polarity Protection | Yes |
| Protocol Standard | PWM(J1850), VPW(J1850), ISO 9141-2, DIS/ISO 14230-4, CAN(J-2284) |
| Operating Temperature | -20℃-50℃, Humidity<70% |
| Banana Socket | 2mm*10; 2mm to 4mm*2 |
| OBD Cable Length | 70cm (27.5inch) / 150cm (59inch) |
| Power Cable Connector | 5.5×2.1 mm |
| Item Weight | 0.4kg |
| External Testing Certification | CE |

Image: Product dimensions and a detailed specifications table for the WOYO CTB007 PRO.

Image: A visual representation of the CTB007 PRO's dimensions, showing its compact size for portability and ease of use.
10. Warranty and Support
For any technical assistance, warranty claims, or product inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.