NJTY V8

Contents

NJTY Fingerprint Padlock V8 User Manual

Model: V8

Introduction

The NJTY V8 Fingerprint Padlock is a smart security device that combines high technology and convenience, designed for users who seek security and efficiency. This manual provides detailed instructions on how to set up, operate, maintain, and troubleshoot your padlock.

Two NJTY V8 Fingerprint Padlocks, one yellow and one black, showing the fingerprint sensor.
NJTY V8 Fingerprint Padlock in yellow and black.
Comparison of a fingerprint padlock and a traditional padlock with a key.
Fingerprint Padlock vs. Traditional Padlock: Keyless convenience.
Key features of the NJTY Fingerprint Padlock: 20 groups fingerprint storage, self-developed chip, long standby time, 0.5s quick unlock, 99% recognition rate, sturdy lock body, USB charging, weight only 72g.
Key Features: 20 fingerprints, 0.5s unlock, USB charging, lightweight.

Setup Instructions

Upon initial use, the padlock is in "experience mode," allowing any fingerprint to unlock it. You must register your own fingerprints for security.

1. Light Indications

  • Fingerprint verification success (factory state): Blue light flashes once.
  • Fingerprint verification success: Green light flashes once.
  • Fingerprint verification failed: Red light flashes three times.
  • Low power alarm: After successful fingerprint verification, the green light flashes once, and the red light flashes three times.

2. Registering the First Fingerprint

If registration times out, you will need to restart. The red light will flash once during a registration timeout. By default, the first registration sets up two fingerprints.

  1. Press and hold your finger on the sensor until the blue-green light (sky blue) illuminates continuously, then lift your finger.
  2. Begin registering your fingerprints:
  3. Lift and press your finger ten times continuously until the green light stops, indicating the first fingerprint has been successfully registered.
  4. After the first fingerprint is successfully registered, the blue light will illuminate. Replace with a second new finger, lift and press it ten times continuously until the green light stops, indicating the second fingerprint has been successfully registered.

Note: When inputting a fingerprint, lift your finger after each press; do not keep it pressed down. During recording, move your finger up, down, left, and right to avoid pressing the same part of the finger ten times.

Diagram showing light indications for fingerprint verification and steps for registering and adding fingerprints.
Visual guide for light indications and fingerprint registration steps.

3. Adding a New Fingerprint

  1. After successfully verifying with an already registered finger, press and hold until the blue-green light illuminates, then lift your finger.
  2. Begin inputting the new fingerprint: lift and press your finger ten times continuously until the green light stops, indicating the new fingerprint has been successfully registered.

4. Setting an Emergency Morse Password

This feature allows you to unlock the padlock using a sequence of presses, useful if fingerprint access is unavailable. (Note: After factory reset, all fingerprints cannot be restored via Morse code.)

  1. After unlocking the fingerprint, press and hold the blue light (do not lift) until the white light illuminates, then release.
  2. After releasing, the green light will illuminate. Each press of the fingerprint sensor counts as one number (e.g., 5 presses = number 5). Press the set number of times and wait for the blue light to illuminate.
  3. Once the blue light illuminates, press the set number of times (e.g., 6 presses = number 6). After pressing the set number of times, wait for the light to turn off.
  4. The number of presses from the green light and the blue light form a two-digit number (e.g., 56). Remember this password.

Important Notes for Morse Code:

  • If no emergency unlock password is set, the default password is 33. If one is set, the default password becomes invalid.
  • After a factory reset, the set password becomes invalid and reverts to the default password.
  • If a timeout occurs during emergency unlock password setup or use, you will exit and need to restart. A red light flashes once for setup timeout, and twice for use timeout.

Operating Instructions

1. Unlocking with Fingerprint

Simply place a registered finger on the fingerprint sensor. The padlock will unlock in approximately 0.5 seconds if the fingerprint is recognized.

Video demonstrating the quick 0.5-second fingerprint unlock feature.
Image highlighting the 0.5s quick unlock feature with a fingerprint graphic.
Fingerprint is the key: 0.5s quick unlock.

2. Using the Emergency Morse Password

If fingerprint unlocking fails or is unavailable:

  1. Press and hold any finger on the sensor until the white light flashes, then release.
  2. After releasing, the green light will illuminate. Press the previously set number of times (e.g., 5 times), then wait for the blue light to illuminate.
  3. Once the blue light illuminates, press the set number of times (e.g., 6 times), then wait for the lights to turn off.
  4. If the red light flashes before the lights turn off, the password is incorrect. If the green light flashes, the password is correct.
  5. If the password is correct, the lock will automatically open and revert to factory settings, requiring new fingerprint registration.

Maintenance

1. Charging the Padlock

The padlock is equipped with a 200mAh rechargeable Li-battery and uses a TYPE-C USB interface for charging. When the low power alarm activates (green light flashes once, red light flashes three times after successful fingerprint verification), it's time to charge.

  • Connect the padlock to a standard USB charger, power bank, or computer USB port using a TYPE-C cable.
  • The padlock can be charged directly, eliminating the need for frequent battery replacement.
Image showing the padlock being charged via a USB cable connected to a power bank.
The padlock can be charged directly via USB.
Graphic illustrating long-lasting battery life with a clock and battery icon.
Enjoy long-lasting battery life with the 200mAh rechargeable battery.

2. Cleaning and Storage

  • Wipe the padlock with a soft, dry cloth to remove dust and dirt.
  • Avoid using abrasive cleaners or solvents that could damage the finish or internal components.
  • Store the padlock in a dry environment, away from extreme temperatures and direct sunlight.

Troubleshooting

1. Fingerprint Not Recognized

  • Symptom: Red light flashes three times after attempting to unlock.
  • Solution:
    • Ensure your finger is clean and dry.
    • Try different angles or parts of your registered finger.
    • If multiple fingerprints are registered, try another registered finger.
    • If the issue persists, try re-registering your fingerprint (see "Registering the First Fingerprint" or "Adding a New Fingerprint" in Setup).
    • Consider using the emergency Morse password if access is urgent.

2. Padlock Not Responding / Low Power

  • Symptom: Padlock does not respond to fingerprint, or low power alarm (green light flashes once, red light flashes three times).
  • Solution:
    • Charge the padlock using a TYPE-C USB cable.
    • Ensure the charging cable and power source are working correctly.

3. Morse Password Incorrect

  • Symptom: Red light flashes before lights turn off during emergency Morse password entry.
  • Solution:
    • Double-check the sequence and number of presses for your Morse password.
    • If you forgot your custom Morse password, the default is 33 (if no custom password was set).
    • If the issue persists, you may need to perform a factory reset (see "Restoring Factory Settings" below).

4. Restoring Factory Settings

This will erase all registered fingerprints and reset the Morse password to default (33 if not set). All fingerprints cannot be restored after this process.

  1. After successful fingerprint verification, press and hold the blue-green light (do not lift) until it illuminates continuously.
  2. The white light will illuminate (continue to press and hold).
  3. Continue holding until the red light illuminates, then release. The green light will flash once, indicating all fingerprints have been cleared and the factory state is restored.

Specifications

FeatureSpecification
Model NumberV8
Unlocking MethodFingerprint
Supported Users20 Fingerprints
Local Management FunctionSupported
Power Supply ModeRechargeable Li-battery
Battery Capacity200mAh
Working Current<50mA
Power InterfaceTYPE-C USB
Working Temperature-20°C to 60°C
Relative Humidity20%~85% (non-condensation)
Antistatic Capacity (ESD)Contact discharge 8KV, non-connected discharge 15KV
Body Size8.3 x 5 x 1.7 cm (3.3 x 2 x 0.7 inch)
Shackle Diameter0.5 cm (0.2 inch)
Weight72g
MaterialAluminum Alloy + ABS
Recommended Usage ScenariosWardrobe, bedside table, shoe cabinet, drawers, luggage, gym lockers, gates.
Parameter table for the Portable Mini Padlock, listing Fingerprint Unlock, Local Management Function, Support Number of Users (20), Shackle Diameter (0.5cm/0.2in), Body Size (8.3x5x1.7cm / 3.3x2x0.7inch), and Material (Aluminum Alloy + ABS).
Detailed specifications for the V8 Fingerprint Padlock.
Collage of images showing the padlock used in various scenarios: on a cabinet, on a refrigerator, on a wire mesh cage, on a gate, and on a backpack.
Widely used for many places, ensuring valuables are secure.

User Tips

  • Compact Design: The padlock is noted for its thin and compact design, making it highly portable for luggage, backpacks, or small cabinets.
  • Battery Life: Keep an eye on the low power alarm (green light then three red flashes) and charge promptly to avoid interruptions. Regular charging ensures consistent performance.
  • Reset Procedure: Familiarize yourself with the factory reset procedure using the Morse code, as this is the primary method to clear all fingerprints or reset the device if issues arise.

Frequently Asked Questions (FAQ)

Q: How long does the battery last?
A: The padlock has a 200mAh rechargeable Li-battery. Battery life depends on usage frequency. The low power alarm (green light flashes once, red light flashes three times after successful fingerprint verification) indicates it's time to charge.
Q: How do I reset the padlock?
A: To reset the padlock to factory settings, follow these steps:
  1. After successful fingerprint verification, press and hold the blue-green light (do not lift) until it illuminates continuously.
  2. The white light will illuminate (continue to press and hold).
  3. Continue holding until the red light illuminates, then release. The green light will flash once, indicating all fingerprints have been cleared and the factory state is restored.
Note that all registered fingerprints will be erased, and the Morse password will revert to default.

Warranty and Support

For detailed product information and support, please refer to the official user manual PDF:

User Manual (PDF): View User Manual PDF

For further assistance, please contact NJTY Official Store customer service.

Certifications and authority detection logos including FC, RoHS, CE, UL, WEEE, ISO 9001:2015.
Authority Detection and Certifications.
Images of NJTY factory and automation equipment, highlighting company strength.
NJTY Company Strength: Cutting-edge production technology and rigorous quality control.

© 2024 NJTY. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.