DAKEFPV F722

Contents

DAKEFPV F722 Flight Controller and ESC Stack User Manual

For FPV Drones and Remote Control Aircraft

1. Introduction

This manual provides detailed instructions for the DAKEFPV F722 Flight Controller Board and its accompanying Electronic Speed Controller (ESC) stack. Designed for high-performance FPV drones and remote control aircraft, this system offers advanced features such as a built-in barometer, On-Screen Display (OSD), and support for various power configurations. Please read this manual thoroughly before installation and operation to ensure safe and optimal performance of your device.

2. Safety Information

  • Always handle electronic components with care to avoid electrostatic discharge.
  • Ensure all power connections are correct before applying power. Incorrect polarity can cause severe damage.
  • Soldering should be performed by experienced individuals. Use appropriate safety gear and ventilation.
  • Never operate your FPV drone or aircraft in unsafe conditions or near people, animals, or property.
  • Disconnect the battery before performing any maintenance or modifications.
  • Keep the flight controller and ESC away from water and moisture.
  • Damage resulting from improper installation or use is not covered under warranty.

3. Package Contents

The DAKEFPV F722 system is available in several configurations. Please verify the contents of your package against the list below.

Option 1 - DAKEFPV F722 120A 30x30 STACK

Package contents for DAKEFPV F722 120A 30x30 STACK
Package contents for DAKEFPV F722 120A 30x30 STACK
  • DAKEFPV F722 Flight Controller x 1
  • DAKEFPV BLS 120A 4 in 1 ESC x 1
  • 35V 1000uF Low ESR Capacitor x 1
  • M3 Nylon Nut x 5
  • M3 Silicone O Ring x 5
  • M3*8mm Silicone Grommets (for FC) x 1
  • M3*8.1mm Silicone Grommets (for ESC) x 1
  • SH 1.0mm 25mm-length 8pin Cable (for FC-ESC connection) x 1
  • SH 1.0mm 75mm-length 8pin Cable x 1
  • M3*30mm Inner-hexagon Screws x 5
  • GPS 6pin cable, Analog VTX 6pin cable, dual-camera 6pin cable x 1
  • XT60 Power Cable (70mm) x 1

Note: When the ESC tail faces the drone's front, use cable #8 for FC-ESC connection. Both ends plug interchangeably.

Option 2 - DAKEFPV F722 120A 30x30 FC

Package contents for DAKEFPV F722 120A 30x30 FC
Package contents for DAKEFPV F722 120A 30x30 FC
  • DAKEFPV F722 Flight Controller x 1
  • Silicone Grommets (random colors) x 8, hexagon screws x 5, hexagon nuts x 5, silicone rings x 5
  • FC12-pin to ESC 8-pin cable, LED/buzzer 4-pin cable x 1
  • GPS 6-pin cable, analog VTX 6-pin cable, dual-camera 6-pin cable x 1, receiver 4-pin cable

Option 3 - DAKEFPV 12S 120A 4 in 1 ESC

Package contents for DAKEFPV 12S 120A 4 in 1 ESC
Package contents for DAKEFPV 12S 120A 4 in 1 ESC
  • DAKEFPV 12S 120A 4 in 1 ESC x 1
  • 35V 1000uF Low ESR Capacitor (Buy 12S ESC Send 63V1000uf Capacitor)
  • FC 12-pin to ESC 8-pin cable (for connecting FC to ESC)
  • XT60 x 1

4. Specifications

General Product Information

  • Brand: DAKEFPV
  • Model Number: F722
  • Material: Metal
  • For Vehicle Type: Airplanes (FPV Drones)
  • Remote Control Peripherals/Devices: Receivers
  • Recommend Age: 14+ years
  • Certification: CE

DAKE F722 30x30 Flight Controller

Specifications table for DAKE F722 Flight Controller
Detailed specifications for the F722 Flight Controller
FeatureSpecification
Product NameDAKE F722 30 x 30 Flight Controller
Main Control ChipSTM32H743
GyroscopeICM42688P
USB Interface TypeType-C
BarometerBuilt-in
OSD ChipAT7456E
BluetoothNone
WIFINot supported
DJI Air Unit ConnectionSupports 6pin direct plug, two wiring methods
6-pin DJI Air Unit Direct PlugSupports DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1 (no wiring changes needed)
FLASH Memory16MB
AmmeterSupported
Input Voltage3-8S LiPo
UART Ports8 groups
Buzzer PadsSupports BZ+, BZ- buzzer access 5V
BOOT ButtonPress and hold during power-up for DFU mode (firmware flashing)
RSSI PadSupported (top right pad)
SmartPort/F.PortNot supported
Flight Firmware TypeBetaFlight (default), ArduPilot
Firmware Target NameDAKEFPVF722
Mounting Hole30.5 x 30.5 mm (4mm hole)
Size36 x 36 x 8 mm
Weight10.5g

DAKE 12S 120A 4 in 1 ESC

Specifications table for DAKE 12S 120A 4 in 1 ESC
Detailed specifications for the 12S 120A 4 in 1 ESC
FeatureSpecification
Product NameDAKE 12S 120A 4 in 1 ESC
FirmwareBLHeli_s / BlueJay
Input Voltage3-8S LiPo
Max Current120A x 4
Peak Current125A x 4 (10S)
Built-in TVS DiodeYes
External Capacitor1000uF low ESR capacitor (included)
ESC Communication ProtocolDshot300/Dshot600/PWM/Bi-directional Dshot
Output VoltageVBAT
Ammeter OutputSupported (Scale=400, Offset=0)
Temperature SensorNot supported
Mounting Hole30.5 x 30.5 mm (4mm hole)
Size45.4 x 42.8 x 6.5 mm
Weight23.5g

Dimensions

Dimensions of F722 Flight Controller and ESC
Physical dimensions of the F722 Flight Controller and ESC
  • FC Mounting Hole: 30.5 x 30.5 mm
  • FC Size: 36 x 36 x 8 mm
  • ESC Mounting Hole: 30.5 x 30.5 mm
  • ESC Size: 45.4 x 42.8 x 6.5 mm
  • Stack Height: 15.8 mm (approx.)

5. Setup

Component Overview

F722 Flight Controller Layout Diagram
F722 Flight Controller Layout with key components and pads labeled
BLS 120A 4-in-1 ESC Layout Diagram
BLS 120A 4-in-1 ESC Layout showing motor pads and power connections

Installation Notes

Important Stack Installation Note
Critical considerations for stack installation
  • Standard Mounting: Always adhere to the standard mounting method for your stack.
  • Orientation: The orientation of the gyroscope and motor sequence can be adjusted through software settings.
  • Inverted Mounting: If you choose an inverted mounting configuration, pay extra attention to ensure sufficient space between the frame, the Flight Controller (FC), and the Electronic Speed Controller (ESC).
  • Silicon Pads: It is critical to swap the silicon pads when changing the positions of the FC and the ESC. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit.
  • Warranty: Please be aware that any damage resulting from improper installation of this nature is not covered under the product warranty.

Wiring Diagrams

Refer to the following diagrams for proper wiring of your DAKEFPV F722 Flight Controller and ESC stack with various peripherals.

Detailed Wiring Diagram for F722 Flight Controller with various peripherals
Comprehensive wiring diagram for the F722 Flight Controller
Connection with FC & Motors and SBUS/ELRS receiver notes
Wiring for FC to Motors and important notes for SBUS/ELRS receivers
  • FC & ESC Connection: The Flight Controller and ESC can be connected via direct soldering or using the included 8-pin cable.
  • Powering Up: To prevent damage from voltage spikes, it is strongly recommended to use the included Low ESR capacitor when powering up the stack.
  • SBUS Receiver: The SBUS signal wire from your receiver must be connected to the dedicated SBUS pad on the front side of the flight controller. This pad internally uses UART2.
  • ELRS Receiver: We recommend connecting the ELRS receiver's TX and RX to the T2 and R2 pads on the flight controller. If you encounter issues with ELRS receivers not being recognized when using a DJI Air Unit simultaneously, you may need to disconnect the SBUS signal wire from the Air Unit harness.

DJI Air Unit Connections

Cable Connection vs DJI O3 Air Unit and RunCam Link/Caddx Vista Air Unit
Connection diagrams for DJI O3 Air Unit and RunCam Link/Caddx Vista Air Unit
  • DJI O3 Air Unit: Use the 6-pin cable provided with the O3 Air Unit for connection.
  • RunCam Link/Caddx Vista Air Unit: Use the 6-pin cable that comes with the H743 stack (refer to accessory No. 11 in Package Option 1). The F722 FC is fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1 without needing to change wiring.

6. Operating Instructions

Battery Capacity Indicator (LiPo Checker)

F722 Flight Controller with LiPo checker feature and pinout diagram
Integrated 4-level battery capacity indicator on the FC

The F722 Flight Controller features a convenient 4-level battery capacity indicator. Once the battery is connected, you can instantly check the battery level directly on the FC, eliminating the need for an external LiPo checker.

LED Light Bar Control

LED light bar pads connection on F722 FC
Connecting and controlling LED light bars

The LED pads on the corners of the flight controller allow you to connect and customize LED light strips for your aircraft. A single press of the BOOT button lets you switch between different lighting modes. To activate the onboard LED effect control mode, long press the BOOT button. Short presses of the BOOT button will then toggle between various preset light effects.

Black Box Functionality

Built-in 16MB large memory FLASH feature
The 16MB onboard FLASH memory for flight data recording

The F722 Flight Controller includes a built-in 16MB FLASH memory, acting as a 'black box'. This continuously records flight status data, including sensor readings, control commands, and fault codes. This data can be retrieved for accident analysis, even in the event of a crash or power outage.

Firmware

The flight controller comes pre-installed with BetaFlight firmware. It also supports ArduPilot. Firmware updates and configuration can be done via the respective configurator software (e.g., BetaFlight Configurator) by connecting the FC to your computer via the Type-C USB port and entering DFU mode (press and hold BOOT button while powering up).

7. Maintenance

  • Regularly inspect all solder joints and connections for signs of wear or damage.
  • Keep the boards clean from dust, dirt, and debris. Use compressed air or a soft brush if necessary.
  • Ensure proper cooling for the ESC, especially during high-current operations. The 120A ESC features an aluminum alloy heat sink for improved heat dissipation.
  • Check for firmware updates periodically to benefit from new features and bug fixes.

8. Troubleshooting

ProblemPossible CauseSolution
Flight Controller not powering onIncorrect power connection, damaged board, faulty battery.Verify battery connection and polarity. Check for visible damage. Test with a known good battery.
Motors not spinning/respondingIncorrect ESC wiring, ESC not calibrated, motor desync, faulty motor/ESC.Check motor wiring to ESC. Calibrate ESCs via BetaFlight. Ensure motor direction is correct. Inspect motors and ESC for damage.
Receiver not detected (SBUS/ELRS)Incorrect wiring, wrong UART selected, SBUS signal wire conflict.Verify receiver wiring to the correct FC pads (SBUS pad for SBUS, T2/R2 for ELRS). Ensure correct UART is enabled in BetaFlight. If using DJI Air Unit with ELRS, try disconnecting the SBUS signal wire from the Air Unit harness.
OSD not displaying informationOSD disabled in firmware, incorrect video connection.Enable OSD in BetaFlight Configurator. Check video input/output connections.
Flight Controller not connecting to computer (DFU mode)Incorrect driver, faulty USB cable, BOOT button not pressed correctly.Install Zadig drivers (if on Windows). Try a different USB cable. Ensure BOOT button is held down while plugging in USB.

User Tips

  • Always perform a dry run (without propellers) after any wiring changes or firmware updates to ensure all components are functioning as expected.
  • Utilize the built-in 16MB black box flash memory for flight logging. This data is invaluable for diagnosing flight performance issues or post-crash analysis.
  • Take advantage of the 4-level battery capacity indicator on the FC for quick battery status checks before and after flights.
  • For optimal performance and longevity, ensure your ESC has adequate airflow, especially the upgraded 120A version with its aluminum alloy heat sink.

9. Warranty & Support

DAKEFPV products are manufactured to high standards. For specific warranty details, please refer to the seller's policy at the time of purchase. Generally, the warranty covers manufacturing defects but does not cover damage caused by:

  • Improper installation or wiring.
  • Misuse, abuse, or negligence.
  • Unauthorized modifications or repairs.
  • Accidents, crashes, or external forces.
  • Voltage spikes or incorrect power input (use of the recommended Low ESR capacitor is crucial).

For technical support or inquiries, please contact your retailer or the DAKEFPV customer service channel provided at the point of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.