1. Introduction
Congratulations on your purchase of the E43 Mosquito RTF (Ready-To-Fly) RC Airplane. This indoor mini plane is designed for beginners and parkflyer enthusiasts, offering stable flight characteristics and easy control. This manual provides essential information for safe assembly, operation, maintenance, and troubleshooting to ensure an enjoyable flying experience.

2. Safety Information
- Always operate the aircraft in open areas, away from people, animals, and obstacles.
- Do not fly near power lines, roads, or water bodies.
- Ensure the battery is fully charged before each flight.
- Keep fingers clear of the propeller when the aircraft is powered on.
- Adult supervision is recommended for users under 14 years of age.
- Store the aircraft and battery in a cool, dry place, away from direct sunlight and heat sources.
3. Package Contents
The E43 Mosquito RTF package includes the following components:
- E43 360mm Wingspan Mosquito Aircraft
- Brushed-614 Motor (pre-installed)
- 4-inch / 100mm Propellers (3 pieces, including spares)
- Brushed 1S/2A Electronic Speed Controller (ESC, pre-installed)
- 1S 120mAh Battery
- e-FHSS Receiver & Transmitter (Remote Control)
- Landing Gear
- USB Charging Cable

4. Specifications
| Feature | Specification |
|---|---|
| Brand | Dancing Wings Hobby |
| Model | E43 Mosquito |
| Wingspan | 360mm |
| Material | Mixed materials (primarily foam with metal components) |
| Motor | Brushed-614 |
| Propeller | 4 inch / 100mm (3 pieces) |
| ESC | Brushed 1S/2A |
| Battery | 1S 120mAh |
| Receiver & Transmitter | e-FHSS |
| Recommended Age | 14+ years |
| Package Dimensions (L x W x H) | 50cm x 20cm x 10cm |
| Package Weight | 0.5 kg |
5. Setup
5.1 Assembly
The E43 Mosquito is an RTF model, meaning most components are pre-assembled. You may need to attach the landing gear and ensure the propeller is securely fastened. Refer to the included diagrams for visual guidance.

5.2 Battery Charging
Use the provided USB charging cable to charge the 1S 120mAh battery. Connect the battery to the charger, and then plug the charger into a USB power source (e.g., computer, USB wall adapter). The indicator light on the charger will show the charging status (typically red for charging, green for fully charged). Do not overcharge the battery.
5.3 Transmitter Battery Installation
Install the required batteries (not included, typically AA or AAA) into the remote control transmitter, observing correct polarity.
5.4 Binding (Frequency Matching)
The aircraft and transmitter need to be bound to each other for communication. Follow these steps:
- Ensure the transmitter is OFF and the throttle stick is at its lowest position.
- Connect the fully charged battery to the receiver on the aircraft. The receiver's indicator light will flash slowly.
- Wait for the receiver's indicator light to start flashing rapidly.
- While holding down the upper left button on the transmitter, turn the transmitter ON.
- The orange light on the transmitter will stay on, and the receiver's light will also become solid, indicating successful frequency matching.
Note: If binding fails, unplug the receiver battery and plug it in again, then repeat steps 2-5.
6. Operating Instructions
6.1 Pre-Flight Check
- Ensure all control surfaces (rudder, elevator) move freely and correctly in response to transmitter inputs.
- Check that the propeller is securely attached and free from damage.
- Verify the battery is fully charged and securely connected.
- Confirm the flying area is clear and safe.
6.2 Take-off
Place the aircraft on a flat surface. Slowly increase the throttle. As the aircraft gains speed, gently apply elevator input to lift off. For hand launches, gently toss the aircraft forward with a slight upward angle while applying throttle.
6.3 Flight Controls
- Throttle (Left Stick Up/Down): Controls motor speed and altitude.
- Rudder (Left Stick Left/Right): Controls yaw (turning left or right).
- Elevator (Right Stick Up/Down): Controls pitch (nose up/down for climbing/descending).
6.4 Landing
Reduce throttle gradually to decrease altitude. Maintain control with elevator and rudder. Aim for a gentle descent and allow the aircraft to glide to a soft landing. Once on the ground, fully reduce throttle.
7. Maintenance
- Cleaning: Wipe the aircraft gently with a soft, dry cloth after each flight to remove dirt or debris.
- Propeller Check: Regularly inspect propellers for cracks, bends, or damage. Replace damaged propellers immediately to ensure safe and efficient flight.
- Battery Care: Do not fully discharge the battery. Charge it before storage if it will not be used for an extended period. Disconnect the battery from the aircraft when not in use.
- Structural Integrity: Periodically check the foam body and carbon fiber rods for any damage. Minor damage can often be repaired with foam-safe glue.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Aircraft does not respond to transmitter. | Not bound, low battery (aircraft or transmitter), transmitter off. | Perform binding procedure. Charge/replace batteries. Turn on transmitter. |
| Motor not spinning or weak thrust. | Low aircraft battery, damaged propeller, motor issue. | Charge aircraft battery. Replace propeller. Contact support if motor is faulty. |
| Aircraft flies erratically or drifts. | Control surfaces not centered, wind interference, damaged control linkage. | Check and adjust trim on transmitter. Fly in calm conditions. Inspect linkages. |
| Binding fails repeatedly. | Incorrect procedure, interference. | Ensure throttle is at zero. Unplug and replug receiver battery before re-attempting binding. Try in a different location away from other electronics. |
9. User Tips
- For beginners, start by practicing in a large, open indoor space or a very calm outdoor area with minimal wind.
- Practice gentle throttle control to maintain a stable altitude before attempting complex maneuvers.
- Always perform a range check before the first flight of the day to ensure reliable signal.
- Consider using a flight simulator to get accustomed to RC controls before flying your actual model.
10. Warranty and Support
For any issues, technical support, or warranty claims, please contact the seller or manufacturer directly. Keep your proof of purchase for reference.