1. Introduction
This manual provides detailed instructions for the installation, setup, and operation of your DAKEFPV F405 V3 Flight Control (FC) and Electronic Speed Controller (ESC) stack. Please read this manual thoroughly before use to ensure proper functionality and safety.
2. Safety Information
- Always disconnect the battery before performing any installation, wiring, or maintenance.
- Ensure all connections are secure and correctly polarized to prevent damage to components.
- Soldering should be performed by experienced individuals. Use appropriate soldering equipment and techniques.
- Verify all voltage outputs before connecting sensitive components like receivers. Incorrect voltage can cause permanent damage.
- Keep the stack away from conductive materials and moisture.
- Improper installation or modification can void your warranty.
3. Package Contents
The DAKEFPV F405 V3 stack is available in different configurations. Please verify your package contents against the options below.
Option 1 - DAKEFPV F405 70A 30x30 STACK

This option includes:
- DAKEFPV F405 Flight Controller x 1
- DAKEFPV BLS 70A 4 in 1 ESC x 1
- 35V 1000uF Low ESR Capacitor x 1
- M3 Nylon Nut x 5
- M3 silicone O Ring x 5
- M3*8mm Silicone Grommets (for FC) x 1
- M3*8.1mm Silicone Grommets (for ESC) x 1
- SH 1.0mm 25mm-length 8pin Cable (for FC-ESC connection) x 1
- GPS 6-pin cable, Analog VTX 6-pin cable, Dual-camera 6-pin cable x 1, Receiver 4-pin cable
- M3*30mm Inner-hexagon Screws x 5
- XT60 Power Cable (70mm) x 1
Note: When the ESC tail faces the drone's front, use the 8-pin cable for FC and ESC connection; both ends plug interchangeably.
Option 2 - DAKEFPV F405 30x30 FC (Flight Controller only)

This option includes:
- DAKEFPV F405 Flight Controller x 1
- Silicone Grommets (random colors) x 8, hexagon screws x 5, hexagon nuts x 5, silicone rings x 5
- FC12-pin to ESC 8-pin cable, LED/buzzer 4-pin cable x 1
Option 3 - DAKEFPV 8S 70A 4 in 1 ESC (ESC only)

This option includes:
- DAKEFPV 8S 70A 4 in 1 ESC
- 35V 1000uF Low ESR Capacitor (For 12S ESC, a 63V 1000uF Capacitor is sent)
- FC 12-pin to ESC 8-pin cable (for connecting FC to ESC)
- XT60 x 1
4. Product Overview
The DAKEFPV F405 V3 Flight Controller and ESC stack offers high performance and rich features for FPV drones.
4.1. Key Features
- Flight Controller: F405 main control chip, Betaflight firmware support, 16M onboard FLASH (black box), barometer, 4 groups of LED light bar pads, DJI pads.
- ESC: Upgraded to 70A continuous current (peak 280A for 10s), supports 6S/4S motors, aluminum alloy heat sink.
- Power: 3-8S LiPo input, 12V 3A + 5V 3A dual independent BEC.
- Gyro: ICM42688P gyroscope with independent LDO power supply and 22uF ultra-large filtering tantalum capacitor.
- Compatibility: Fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1 (no wire changes needed).
- Motor Support: Supports 8 motors and 4 servos, can be used for Y6/fixed-wing aircraft.
- Connectivity: 8 UARTs, ample pads for custom connections.
- Battery Indicator: 4-level battery capacity indicator on the FC.

Figure 1: DAKE F405 BLS 70A Stack Features Overview

Figure 2: Detailed Features of the F405 Flight Controller
5. Setup and Installation
5.1. Stack Assembly
The F405 Flight Controller and ESC are designed to be stacked. Ensure correct orientation and secure mounting.

Figure 3: F405 Flight Controller + 70A ESC Stack
Video 1: Product Overview and Assembly Demonstration
5.2. Important Stack Installation Note

When installing your stack, adhere to the standard mounting method. The orientation of the gyro and motor sequence can be adjusted through settings. If you opt for an inverted manner, be extra careful about the space between the frame, the FC, and the ESC.
It's critical to swap the silicon pads when changing the positions of the FC and the ESC, as illustrated in the diagram. This step is vital to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Please be aware that any damage resulting from improper installation of this nature is not covered under the Warranty.

Figure 4: Ensure sufficient space between FC and ESC components.
5.3. Wiring Diagram
Refer to the comprehensive wiring diagram for connecting all components to the F405 Flight Controller and ESC.

Figure 5: Connection with the FC & Motors
5.4. Specific Connections
5.4.1. SBUS Receiver Connection

When using an SBUS receiver, the SBUS signal wire of the receiver must be connected to the SBUS pad on the front side of the flight controller (this pad internally uses UART2).
If you are also using the DJI Air Unit (O3/Link/Vista/Air Unit V1), you will need to disconnect the SBUS signal wire from the Air Unit harness. Failure to do so will prevent the SBUS receiver from being properly recognized by the flight controller. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.
WARNING: Do NOT connect this wire if using an external SBUS receiver to ensure it works properly. Always verify the voltage output of the receiver connection point before connecting your receiver to prevent damage.
5.4.2. ELRS Receiver Connection

We recommend connecting the ELRS receiver's TX and RX to the T2 and R2 pads on the flight controller. However, when using the DJI Air Unit simultaneously, some ELRS receivers may not be recognized properly by the flight controller. If you encounter this issue, you need to disconnect the SBUS signal wire from the Air Unit harness. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.
5.4.3. DJI Air Unit Connection
The F405 FC is designed for direct plug-in compatibility with DJI Air Units.

Figure 6: Cable Connection vs DJI O3 Air Unit (Use 6-pin cable comes with the O3 Air Unit)

Figure 7: Cable Connection vs RunCam Link/Caddx Vista Air Unit (Use 6-pin cable comes with the H743 stack)

Figure 8: Cable Connection vs DJI Air Unit V1 (Use 6-pin cable comes with the H743 stack)
5.5. Powering Up and Protection

To prevent the stack from being burnt out by voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor included in the package. The onboard TVS protection diode and Japanese TDK SMD filter capacitors further enhance power stability.
6. Operating Instructions
6.1. LED Light Bar Pads

The LED pads at the corners of the flight controller allow you to decorate your aircraft with your favorite LED light strips. A single press of the BOOT button lets you switch between different lighting modes. A long press of the BOOT button switches to the LED light effect control mode, and short presses toggle between various preset light effects.
6.2. Battery Capacity Indicator

On the side of the flight controller, you will find a 4-level battery capacity indicator. As soon as you connect the battery, you can instantly see the battery level, saving you the hassle of needing to put on glasses to check the battery status.
7. Maintenance
- Regularly inspect all solder joints and connections for signs of wear or damage.
- Keep the FC and ESC clean and free from dust and debris. Use compressed air or a soft brush for cleaning.
- Ensure adequate airflow around the ESC to prevent overheating, especially during demanding flights.
- Periodically check for firmware updates for both the FC (Betaflight) and ESC to ensure optimal performance and access to new features.
8. Troubleshooting
- Receiver Not Recognized: If using an external SBUS or ELRS receiver alongside a DJI Air Unit, ensure the SBUS signal wire from the Air Unit harness is disconnected.
- Component Damage on Power-up: Always use the recommended Low ESR capacitor to mitigate voltage spikes. Double-check all wiring, especially power and signal lines, before connecting the battery. Verify voltage outputs on FC pads before connecting sensitive components.
- Short Circuit after Installation: Re-check the spacing between the FC and ESC, especially around the USB port. Ensure silicon pads are correctly placed to prevent contact.
- ESC Overheating: Ensure proper ventilation and consider propeller balance. Verify motor and ESC settings in your flight controller software.
- Flight Instability: Check gyro orientation and motor sequence settings in Betaflight. Ensure all motors are spinning in the correct direction.
9. Specifications
9.1. DAKEFPV F405 Flight Controller
| Feature | Specification |
|---|---|
| Main Control Chip | STM32F405 |
| Gyroscope | ICM42688P |
| Input Voltage | 3-8S LiPo |
| BEC Output | 5V 3A, 12V 3A |
| OSD | Yes |
| Black Box | 16MB Flash |
| UART Ports | 8 |
| Mounting Holes | 30.5 x 30.5 mm (M4 holes) |
| Dimensions | 36 x 36 x 8 mm |
| Weight | 10.5g |
9.2. DAKEFPV BLS 70A 4-in-1 ESC
| Feature | Specification |
|---|---|
| Product Name | DAKE BLS 70A 4 in 1 ESC |
| Firmware | BLHeli_S / BlueJay |
| Input Voltage | 3-8S LiPo |
| Continuous Current | 70A x 4 |
| Burst Current | 80A x 4 (10s) |
| Built-in Capacitor | 1000uF high-frequency capacitor (package included) |
| ESC Protocol | Dshot300/Dshot600/PWM/Bi-directional Dshot |
| ESC Telemetry | Yes |
| Mounting Holes | 30.5 x 30.5 mm (M4 holes) |
| Dimensions | 42.4*42.6*6.5mm |
| Weight | 23.5g |

Figure 9: Dimensions of the F405 Stack
10. User Tips
- Verify Voltage: Before connecting any receiver, always use a multimeter to verify the voltage output on the FC pins to ensure it matches your receiver's requirements (e.g., 5V). Some users have reported issues with incorrect voltage on receiver connection points.
- Capacitor for High Voltage: While a 35V capacitor is included, for 8S setups, some users recommend a higher voltage capacitor (e.g., 63V) for added protection against voltage spikes.
- Check ESC Markings: Upon receiving your ESC, verify any markings or documentation to confirm the voltage and current ratings match your order, as some users have noted discrepancies between product images and actual items.
- Ample UARTs: The F405 FC offers plenty of UARTs, providing flexibility for connecting various peripherals.
- Good Value: Many users find this stack to be a cost-effective solution that performs comparably to more expensive alternatives.
11. Warranty and Support
DAKEFPV products are designed for high performance and reliability. Please refer to the safety information and installation notes carefully. Damage resulting from improper installation, incorrect wiring, or unauthorized modifications may not be covered under warranty.
For technical support, firmware updates, or further assistance, please visit the official DAKEFPV website or contact their customer service.