HGLRC 60A 6S V1 4-in-1 ESC

Contents

HGLRC 60A 6S V1 4-in-1 ESC User Manual

Model: 60A 6S V1 4-in-1 ESC

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your HGLRC 60A 6S V1 4-in-1 Electronic Speed Controller (ESC). Designed for high-performance RC FPV racing and freestyle drones, this ESC features BLHELI_S firmware and supports DShot150/300/600 protocols, ensuring stable output and strong flight capabilities. Please read this manual thoroughly before use to ensure proper setup and safe operation.

Specifications

Feature Detail
Product Name HGLRC 60A 6S V1 ESC
Input Voltage 2-6S Lipo
Ammeter Supported
Continuous Current 60A
Peak Current 65A (5 seconds)
Supported Protocols DShot150/300/600
Firmware Q-H-40 (BLHELI_S)
Size 37mm x 43mm
Mounting Pitch 30.5mm x 30.5mm (M3)
Weight 14g
HGLRC 60A 6S V1 ESC Product Parameters and Components
Figure 1: Product parameters and included components.

This image visually summarizes the key specifications and shows the ESC board alongside its accessories.

HGLRC 60A 6S V1 ESC Dimensions and Weight
Figure 2: Physical dimensions and weight of the ESC and its packaging.

The ESC measures 37mm x 43mm with a 30.5mm x 30.5mm M3 mounting pattern and weighs 14g. The total package weight is approximately 40g.

Setup and Installation

Careful installation is crucial for the performance and longevity of your ESC. Follow these steps for proper setup:

  1. Mounting: Secure the 4-in-1 ESC to your flight controller stack using M3 screws and vibration-damping grommets (if included). Ensure proper orientation as per your flight controller's manual and drone frame design. The mounting pitch is 30.5mm x 30.5mm.
  2. Power Connection: Solder the thick red wire to the 'BAT' pad and the thick black wire to the 'GND' pad on the ESC. These connect directly to your LiPo battery connector. It is highly recommended to solder the included low ESR capacitor across the main battery pads (positive to BAT, negative to GND) to filter voltage spikes and protect the ESC and other components.
  3. Motor Connections: Solder your four motor wires to the corresponding M1, M2, M3, and M4 pads on the ESC. Ensure the motor order and rotation direction match your flight controller's configuration (e.g., Betaflight).
  4. Flight Controller Connection: Connect the signal wire harness from the ESC to your flight controller. This typically involves pads for motor signals (e.g., M1-M4 or S1-S4), current sensor (CUR), and sometimes telemetry. Refer to your flight controller's manual for the exact pinout. The ESC has a 'CUR' pad for current sensor output.
  5. Firmware Configuration: The ESC comes pre-loaded with BLHELI_S firmware (Q-H-40). You can connect the ESC to your computer via your flight controller (using passthrough) and use the BLHeliSuite software to configure settings, update firmware, or reverse motor direction if needed.
HGLRC 60A 6S V1 ESC with included accessories
Figure 3: HGLRC 60A 6S V1 4-in-1 ESC and its accessories, including power wires and capacitor.

This image shows the main ESC board, a capacitor, a signal wire harness, power wires, and mounting grommets, which are essential for installation.

Top view of HGLRC 60A 6S V1 ESC showing solder pads
Figure 4: Top view of the ESC, highlighting the BAT, GND, M1-M4, and CUR solder pads for connections.

This detailed view is critical for identifying the correct solder points for battery input, motor outputs, and current sensor signal.

Operating Instructions

Once installed and configured, the HGLRC 60A 6S V1 4-in-1 ESC operates in conjunction with your flight controller to control the speed and direction of your drone's motors.

  • Power On: Connect your LiPo battery to the drone. The ESC will typically emit a series of beeps indicating it has powered on and is ready.
  • Arming: Arm your drone via your flight controller's arming sequence (e.g., stick commands on your radio transmitter). The motors will typically spin slowly or make a distinct sound to indicate they are armed.
  • Motor Control: The flight controller sends DShot digital signals to the ESCs, which then translate these signals into precise motor speed control. The DShot150/300/600 protocols offer excellent noise immunity and fast response times.
  • Current Monitoring: The integrated ammeter provides current consumption data to your flight controller, allowing for accurate battery monitoring and OSD (On-Screen Display) information.
  • Disarming: Disarm your drone after flight using the designated stick command or switch on your radio.

Maintenance

To ensure optimal performance and extend the lifespan of your HGLRC ESC, follow these maintenance guidelines:

  • Regular Inspection: Periodically check the ESC for any signs of physical damage, loose solder joints, or burnt components.
  • Cleaning: Keep the ESC clean from dust, dirt, and debris. Use a soft brush or compressed air to gently remove any buildup. Avoid using liquids directly on the board.
  • Heat Management: Ensure adequate airflow around the ESC during operation to prevent overheating. Avoid covering the ESC with excessive tape or components that restrict cooling.
  • Capacitor Check: Inspect the external capacitor for any bulging or damage. A damaged capacitor can lead to voltage spikes and ESC failure.
  • Firmware Updates: Occasionally check for new BLHELI_S firmware versions. Updates can improve performance, add features, or fix bugs.

Troubleshooting

If you encounter issues with your HGLRC 60A 6S V1 4-in-1 ESC, refer to the following common problems and solutions:

Problem Possible Cause Solution
Motor not spinning / erratic behavior Loose motor wire, incorrect motor direction, desync, damaged motor/ESC. Check all motor solder joints. Verify motor direction in BLHeliSuite. Adjust motor timing or increase DShot protocol if desyncs occur. Test with a different motor if possible.
ESC gets excessively hot Overcurrent, poor airflow, incorrect motor/prop combination, short circuit. Ensure props are correctly sized for motors. Check for obstructions to airflow. Inspect for any shorts. Reduce throttle limits if consistently overheating.
No power to flight controller / other components Main battery connection issue, damaged ESC power delivery. Verify main battery solder joints (BAT/GND). Check the external capacitor. Ensure no shorts are present.
Current sensor not working Incorrect wiring to flight controller, flight controller not configured for current sensor. Check the 'CUR' signal wire connection. Ensure current sensor is enabled and calibrated in your flight controller software (e.g., Betaflight).

If problems persist, consult online FPV forums or contact HGLRC support for further assistance.

User Tips

  • Solder Quality: Always use a good quality soldering iron and leaded solder for strong, reliable connections. Cold solder joints are a common cause of issues.
  • Capacitor Importance: Do not skip installing the included low ESR capacitor. It significantly reduces electrical noise and protects your ESC from voltage spikes, especially on 6S setups.
  • Motor Wire Length: Keep motor wires as short as possible to minimize electrical noise and resistance, but long enough to allow for easy soldering and maintenance.
  • Insulation: After soldering, ensure all exposed solder joints are properly insulated with heat shrink tubing or liquid electrical tape to prevent short circuits.

Warranty and Support

For warranty claims, technical support, or further inquiries, please contact the retailer or manufacturer directly. Keep your proof of purchase for any warranty-related issues. Specific warranty terms and conditions may vary by region and retailer.

© 2023 HGLRC. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.