JIKONG JK-B2A8S20P-HC

Contents

JIKONG JK BMS V19 Smart BMS User Manual

Model: JK-B2A8S20P-HC

Brand: JIKONG

JIKONG JK BMS V19 Smart BMS main product image with key features

1. Safety Information

Please read this manual carefully before installation and operation. Failure to follow instructions may result in damage to the BMS, battery pack, or personal injury.

  • Always wear appropriate personal protective equipment (PPE) when working with batteries.
  • Ensure all wiring is correct and secure before applying power. Incorrect wiring can cause severe damage or fire.
  • Do not short-circuit the battery terminals or BMS connections.
  • Keep the BMS away from water, moisture, and flammable materials.
  • Do not attempt to open or modify the BMS unit.
  • Work in a well-ventilated area.
  • This BMS is designed for Li-ion, LiFePo4, and LTO battery types. Ensure your battery chemistry matches the BMS settings.

2. Package Contents

Verify that all items are present in your package:

  • JIKONG JK BMS Unit (Model: JK-B2A8S20P-HC)
  • Operating Manual (PDF available online)
  • Mounting Screws (typically 4 or 6, depending on model)
  • NTC Temperature Sensor (40cm)
  • Activation Switch (50cm)
  • Balance Wires (70cm)
  • CAN Cable (25cm, for models with CAN function)

Note: Specific components may vary slightly based on the exact model variant.

Packing list for JK-B2A8S20P-HC model

Figure 2.1: Typical Package Contents for JK-B2A8S20P-HC

3. Specifications

The JIKONG JK BMS V19 offers robust features for battery management. Below are the key specifications:

FeatureSpecification (JK-B2A8S20P)
Number of Battery Strings (Li-ion)3S-8S
Number of Battery Strings (LiFePo4)4S-8S
Number of Battery Strings (LTO)6S-8S
Balance MethodActive Balance (Full State On)
Balance Current2A
Conductive Resistance in Main Circuit0.3mΩ
Continuous Discharge Current200A
Continuous Charge Current200A
Maximum Discharge Current [MAX 2min]300A
Over Charge Protection10-200A
Other Interfaces (Customized)RS485, CANBUS HEAT
Size (mm)153*126*18 (approx.)
Wiring OutputCommon Port
Single Cell Voltage Range1-5V
Voltage Acquisition Accuracy±5mV
Over Charge Protection Voltage1.2-4.35V Adjustable
Over Current Detect Delay2-120S Adjustable
Temperature Detection1 Pcs
Temp ProtectionYes
Short Circuit ProtectionYes
Coulomb CounterYes
Bluetooth FunctionSupport for Android/iOS

For detailed specifications of other models, please refer to the official PDF manual.

Table of JIKONG Product Specifications for different BMS models

Figure 3.1: JIKONG Product Specifications Overview

4. Setup and Installation

4.1. Wiring Diagram

Proper wiring is critical for the safe and correct operation of your BMS. Follow the diagram carefully:

Detailed wiring diagram for connecting the BMS to a battery pack, load, and charger

Figure 4.1: BMS Wiring Diagram

  • B- (Battery Negative): Connect the main negative terminal of your battery pack to the B- terminal on the BMS.
  • P- (Load/Charger Negative): Connect the negative terminal of your load and charger to the P- terminal on the BMS.
  • Balance Wires: Connect the balance wires from your battery pack to the sampling port on the BMS. Ensure the order is correct, starting from the first cell's positive terminal (B1) up to the last cell's positive terminal (B+).
  • Heating Cable (if applicable): Connect the heating cable to the designated port on the BMS and to your heating element.
  • NTC Sensor: Place the NTC temperature sensor on a representative cell or within the battery pack for accurate temperature monitoring. Connect it to the NTC port on the BMS.
  • Other Ports: Connect optional accessories like RS485, CAN, GPS, or display units to their respective ports as needed.

Important: Double-check all connections before proceeding to activation. Incorrect wiring can permanently damage the BMS and battery.

4.2. Device Activation

The BMS does not have a physical power-on switch. It activates under specific conditions:

  1. Pre-Activation Check: Before starting, ensure all balance cables are correctly connected, and the main P- and B- connections are secure. Verify the BMS is firmly mounted to the battery pack.
  2. Charging Activation: The BMS is designed for charging activation. After the battery pack assembly is complete, connect a charger. The charger voltage must be at least 2V higher than the current battery pack voltage for the BMS to power on.
  3. Key/Display Activation: If you have an optional display screen or activation button, connect it to the BMS. You can then activate the BMS by pressing the button or through the display interface.

5. Operating Your JIKONG JK BMS

5.1. Smart BT APP Operation

The JIKONG JK BMS can be fully managed and monitored via its dedicated smartphone application.

  1. APP Download:
    • iOS: Search for
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.