FGHGF AMIBOT Animal Premium H2O Connect X782, Spirit Motion X810, Origin X910SKD, Animal Motion X910, Domoova DRV100

Contents

Side Brush Motor Instruction Manual

For AMIBOT Animal Premium H2O Connect X782, Spirit Motion X810, Origin X910SKD, Animal Motion X910, Domoova DRV100

Introduction

This document provides essential information for the safe and effective installation, operation, and maintenance of your replacement side brush motor. This motor is designed for specific AMIBOT and Domoova robot vacuum cleaner models to ensure optimal cleaning performance. Please read this manual thoroughly before proceeding with installation.

Safety Information

  • Always power off and unplug your robot vacuum cleaner before attempting any installation or maintenance.
  • Use appropriate tools for disassembly and assembly to prevent damage to the robot or injury.
  • Keep small parts away from children and pets.
  • If you are unsure about any step, consult a qualified technician or the robot vacuum's original manual.

Package Contents

Your package should contain the side brush motor(s) as ordered. Please verify the contents upon receipt.

Two side brush motors, one for left and one for right side, with wiring and mounting plates.
Image: Two side brush motors, showing the top view with circuit boards and connectors. These are typically installed as left and right units.

Setup and Installation

Follow these general steps to replace the side brush motor. Specific disassembly instructions may vary by robot vacuum model; refer to your robot's original service manual if available.

  1. Power Off: Ensure your robot vacuum cleaner is completely powered off and disconnected from its charging base.
  2. Access Side Brush Area: Carefully turn the robot vacuum upside down. Locate the side brush assembly. You may need to remove the side brush itself first.
  3. Remove Old Motor:
    • Unscrew any retaining screws holding the side brush motor cover or the motor assembly in place.
    • Gently disconnect the electrical connector from the old motor.
    • Remove the old motor assembly.
  4. Install New Motor:
    • Identify the correct orientation for the new motor (Left 'L' or Right 'R' if applicable). The images show distinct mounting plates.
    • Connect the electrical connector to the new motor. Ensure it clicks securely into place.
    • Position the new motor assembly into its designated slot.
    • Secure the motor assembly with the retaining screws. Do not overtighten.
  5. Reassemble: Reattach the side brush and any covers that were removed during disassembly.
  6. Test: Place the robot vacuum back on its wheels, power it on, and initiate a cleaning cycle to verify that the side brush spins correctly.
Close-up of a side brush motor, showing the mounting holes and electrical connector. This is identified as the 'L side' variant.
Image: Detailed view of the 'L side' side brush motor, highlighting the mounting points and connector.
Close-up of a side brush motor, showing the mounting holes and electrical connector. This is identified as the 'R side' variant.
Image: Detailed view of the 'R side' side brush motor, highlighting the mounting points and connector.

Operating Instructions

The side brush motor operates automatically as part of your robot vacuum cleaner's cleaning cycle. No direct user interaction with the motor itself is required after installation. Ensure the side brush is free from obstructions for optimal performance.

Maintenance

  • Regular Cleaning: Periodically remove the side brush and clean any hair, dust, or debris that may have accumulated around the brush shaft and motor area. This prevents strain on the motor.
  • Connection Check: Occasionally inspect the electrical connection to the motor to ensure it remains secure.
  • Visual Inspection: Check the motor and its mounting for any signs of wear, damage, or loose screws.

Troubleshooting

ProblemPossible CauseSolution
Side brush not spinning or spinning slowly.
  • Obstruction (hair, debris) around the brush or motor.
  • Loose or disconnected electrical wiring.
  • Faulty motor.
  • Power off the robot and clear any obstructions.
  • Check the electrical connector for a secure fit.
  • If obstructions are cleared and connection is secure, the motor may need replacement.
Unusual noise from the side brush area.
  • Debris caught in the motor or brush mechanism.
  • Improper installation or loose components.
  • Power off the robot and inspect for and remove any debris.
  • Verify that the motor is securely mounted and all screws are tightened.

Specifications

  • Brand: FGHGF
  • Material: Metal, ABS Plastic
  • Vacuum Part Type: Motors
  • Type: Vacuum Cleaner Parts
  • Origin: Mainland China
  • Compatible Robot Vacuum Models:
    • AMIBOT Animal Premium H2O Connect X782
    • AMIBOT Spirit Motion X810
    • AMIBOT Spirit Origin X910SKD
    • AMIBOT Animal Motion X910
    • Domoova DRV100
  • Approximate Package Dimensions (L x W x H): 14 cm x 10 cm x 18 cm
  • Approximate Package Weight: 0.22 kg

User Tips

  • Verify Compatibility: Before purchasing, always double-check that the motor is compatible with your specific robot vacuum model to avoid installation issues.
  • Left vs. Right: Some robot vacuums may use distinct left and right side brush motors. Ensure you order the correct side(s) or a set if both are needed.
  • Gentle Handling: When installing, handle the motor and its delicate wiring with care to prevent damage.

Warranty and Support

For warranty information, please refer to the terms provided by your original seller or contact them directly. For technical support or further assistance with installation, consult the manufacturer of your robot vacuum cleaner or the seller of this replacement part.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.