1. Introduction
This manual provides essential information for the safe and efficient operation of your PowMr Hybrid Solar Inverter. This device is a multi-functional inverter/charger, combining functions of an inverter, MPPT solar charger, and battery charger to offer uninterruptible power support in a portable size. Its comprehensive LCD display allows user-configurable and easy-accessible button operation such as battery charging current, AC/solar charger priority, and acceptable input voltage based on different applications.
Key Features:
- Pure sine wave output inverter.
- Supports two battery voltage modes: 2300W in 12V battery mode and 4200W in 24V battery mode.
- User-configurable input voltage range for utility grid (for household appliances/personal computers).
- Adjustable charging current via LCD based on battery requirements.
- Capable of powering loads simultaneously from solar energy and utility grid.
- AC input compatible with both mains and generator.
- Automatic restart function upon restoration of mains power.
- Integrated overload, over temperature, and short circuit protection.
- Intelligent battery charging design for optimized battery utilization.
- RS485 port for communication with Battery Management Systems (BMS).
- Cold start function.
- Built-in MPPT solar charge controller with an operating voltage range of 55V~500V and an open circuit voltage of 500Voc.
- Optional WIFI remote monitoring capability.
- Optional RGB lamp indicating inverter status.
2. Setup and Installation
Before installation, ensure the inverter is placed in a well-ventilated area, away from direct sunlight, heat sources, and moisture. It should be mounted vertically on a wall or sturdy surface.
2.1 Component Identification
Familiarize yourself with the inverter's connections and display.


2.2 System Connection Diagram
The following diagram illustrates a typical system connection for the hybrid solar inverter, integrating solar power, utility/generator input, battery storage, and output to home appliances.

Connection Steps:
- Battery Connection: Connect your 12V or 24V lithium or lead-acid battery bank to the designated battery terminals. Ensure correct polarity.
- Solar Panel Connection: Connect your solar PV array to the PV IN terminals. Ensure the PV array MPPT voltage range (55V-500V DC) and maximum open circuit voltage (500V DC) are respected. Max PV array power is 4000W.
- AC Input Connection: Connect the utility grid or a generator to the AC IN terminals. The inverter is compatible with both mains and generator AC inputs.
- AC Output Connection: Connect your home appliances or load to the AC OUT terminals. The inverter provides a single-phase 230V output.
- Grounding: Ensure the inverter is properly grounded according to local electrical codes.
2.3 Battery Type Compatibility
The inverter is compatible with multiple battery types, including AGM, GEL, FLD, LI (Lithium), SLD, and USER-defined settings. When solar energy is present, setting the battery type to 'LI' will activate the lithium battery after 3 seconds.

3. Operating Instructions
3.1 Powering On/Off
- Power On: Ensure all connections are secure. Turn on the battery breaker first, then the AC input breaker (if connected), and finally the solar input breaker (if connected). The inverter will perform a self-test and then begin operation.
- Cold Start Function: The inverter supports a cold start function, allowing it to power on directly from the battery without AC input.
- Power Off: Reverse the power-on sequence: turn off solar input, then AC input, and finally the battery breaker.
3.2 LCD Display and Settings
The LCD display provides real-time operational status and allows configuration of various parameters. Refer to the detailed user manual (PDF, if available) for specific menu navigation and parameter settings, including:
- Setting the input voltage range for the utility grid (e.g., for sensitive electronics or standard appliances).
- Adjusting the battery charging current.
- Configuring AC/solar charger priority.
- Monitoring input/output voltage, frequency, battery status, and load percentage.
3.3 Remote Monitoring (Optional)
If your model includes the optional WIFI module, you can monitor the inverter's performance and status remotely via a dedicated application. Follow the instructions provided with the WIFI module for setup and connection.
3.4 Status Indicator (Optional)
Models with an optional RGB lamp will display different colors to indicate the inverter's operational status (e.g., green for normal operation, yellow for warning, red for fault). Consult the full manual for a complete list of RGB lamp indications.
4. Maintenance
Regular maintenance ensures the longevity and optimal performance of your PowMr Hybrid Solar Inverter.
- Cleaning: Keep the inverter's exterior clean and free from dust. Use a dry, soft cloth. Do not use liquid cleaners.
- Ventilation: Ensure the cooling vents are unobstructed to prevent overheating. Periodically check the cooling fans for proper operation.
- Connections: Periodically check all electrical connections (battery, solar, AC input/output) for tightness and signs of corrosion.
- Battery Health: Monitor your battery bank's health and charge levels. Ensure the intelligent charging design is optimizing battery life.

5. Troubleshooting
The inverter is equipped with protection features to handle various issues. If a fault occurs, the inverter will typically display an error code or status on the LCD and may shut down to protect itself and connected equipment.
- Overload Protection: If the connected load exceeds the inverter's capacity (2300W for 12V mode, 4200W for 24V mode), the inverter will trigger an overload alarm and may shut down. Reduce the load and restart the inverter.
- Over Temperature Protection: If the internal temperature of the inverter becomes too high, it will activate over temperature protection and shut down. Ensure proper ventilation and clear any obstructions from the cooling vents.
- Short Circuit Protection: In case of a short circuit on the output, the inverter will immediately shut down. Identify and resolve the short circuit before restarting.
- No Output: Check all input connections (battery, solar, AC utility/generator). Verify battery voltage is within the operating range. Check for any error codes on the LCD.
6. Specifications
Detailed technical specifications for the PowMr Hybrid Solar Inverter Model POW-HVM4.2K-24V-D.

| Category | Parameter | Value |
|---|---|---|
| General | Model | POW-HVM4.2K-24V-D |
| Certification | CE | |
| Is Smart Device | Yes | |
| Inverter Output | Nominal Input Voltage | 230V |
| Rated Output Power (12V Battery Mode) | 2300VA / 2300W | |
| Rated Output Power (24V Battery Mode) | 4200VA / 4200W | |
| Output Voltage Wave Form | Pure Sine Wave | |
| Output Voltage Regulation | 230V ±5% | |
| Output Frequency | 50HZ / 60HZ | |
| Efficiency & Protection | Peak Efficiency | 94% |
| Surge Capacity | 2 * Rated Power for 5 Seconds | |
| Overload/Over Temperature/Short Circuit | Protection Included | |
| No Load Power Consumption (12V) | 20W | |
| No Load Power Consumption (24V) | 30W | |
| Battery | Nominal DC Input Voltage (12V Mode) | 12V |
| Nominal DC Input Voltage (24V Mode) | 24V | |
| Cold Start Voltage (12V / 24V) | 11.5V / 23V | |
| Utility Charging Mode | Charging Current (UPS) | 100A |
| Floating Charging Voltage (12V) | 13.5V | |
| Floating Charging Voltage (24V) | 27V | |
| Solar Charging Mode | Max. PV Array Power | 4000W |
| Nominal PV Voltage | 240V | |
| PV Array MPPT Voltage Range | 55V-500V | |
| Max. PV Array Open Circuit Voltage | 500V | |
| Max Charging Current (MPPT) | 100A | |
| Environmental & Physical | Operating Temperature Range | -20°C to 55°C |
| Storage Temperature | -20°C ~ 60°C | |
| Dimension (D*W*H) | 405*305*108mm | |
| Net Weight | 6.7KG |
7. Warranty and Support
Your PowMr Hybrid Solar Inverter is designed for reliable performance. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or contact PowMr customer support. The inverter includes an RS485 port for communication with Battery Management Systems (BMS), which can be utilized for advanced monitoring and diagnostics.
8. User Tips
- Off-Grid Capability: This inverter is designed to operate solely with solar energy and batteries, even without a connection to the utility grid. This makes it ideal for remote installations or as a backup power system.
- Lithium Battery Activation: When using lithium batteries, ensure the battery type is set to 'LI' in the inverter's settings. The inverter will automatically activate the lithium battery after 3 seconds when solar energy is present.
- Load Management: To maximize efficiency and prevent overloads, monitor your connected loads and ensure they do not exceed the inverter's rated output power for your chosen battery voltage mode (2300W for 12V, 4200W for 24V).